Page 1 :
(Class – XI), Question 9.1:, A steel wire of length 4.7 m and cross-sectional area 3.0 × 10–5 m2 stretches by the same, amount as a copper wire of length 3.5 m and cross-sectional area of 4.0 × 10–5 m2 under, a given load. What is the ratio of the Young’s modulus of steel to that of copper?, Answer 9.1:, Length of the steel wire, L1 = 4.7 m, Area of cross-section of the steel wire, A1 = 3.0 × 10–5 m2, Length of the copper wire, L2 = 3.5 m, Area of cross-section of the copper wire, A2 = 4.0 × 10–5 m2, Change in length = ΔL1 = ΔL2 = ΔL, Force applied in both the cases = F, Young’s modulus of the steel wire:, , … (i), Young’s modulus of the copper wire:, , Dividing (i) by (ii), we get:, , The ratio of Young’s modulus of steel to that of copper is 1.79: 1., , 1

Page 2 :
Question 9.2:, Figure 9.11 shows the strain-stress curve for a given material. What are (a) Young’s, modulus and (b) approximate yield strength for this material?, , Fig. 9.11, Answer 10.2:, It is clear from the given graph that for stress 150 × 106 N/m2, strain is 0.002., , a), , Young’s modulus, Y =, , 𝑆𝑡𝑟𝑒𝑠𝑠, 𝑆𝑡𝑟𝑎𝑖𝑛, , Hence, Young’s modulus for the given material is 7.5 ×1010 N/m2., b) The yield strength of a material is the maximum stress that the material can sustain, without crossing the elastic limit., It is clear from the given graph that the approximate yield strength of this material is 300, × 106 Nm/2 or 3 × 108 N/m2., , 2

Page 3 :
Question 9.3:, The stress-strain graphs for materials A and B are shown in Fig. 9.12., , Fig. 9.13, The graphs are drawn to the same scale., a) Which of the materials has the greater Young’s modulus?, b) Which of the two is the stronger material?, , Answer 9.3:, (a) A, (b) A, For a given strain, the stress for material A is more than it is for material B, as shown in, the two graphs., 𝑆𝑡𝑟𝑒𝑠𝑠, , Young’s modulus = 𝑆𝑡𝑟𝑎𝑖𝑛, For a given strain, if the stress for a material is more, then Young’s modulus is also, greater for that material. Therefore, Young’s modulus for material A is greater than it, is for material B., The amount of stress required for fracturing a material, corresponding to its fracture point,, gives the strength of that material. Fracture point is the extreme point in a stress-strain, curve. It can be observed that material A can withstand more strain than material B., Hence, material A is stronger than material B., , 3

Page 4 :
Question 9.4:, Read the following two statements below carefully and state, with reasons, if it is true, or false., a) The Young’s modulus of rubber is greater than that of steel;, b) The stretching of a coil is determined by its shear modulus., Answer 9.4:, (a) False, (b) True, For a given stress, the strain in rubber is more than it is in steel., Young’s modulus, Y =, , 𝑆𝑡𝑟𝑒𝑠𝑠, 𝑆𝑡𝑟𝑎𝑖𝑛, , For a constant stress: 𝑌 ∝, , 1, 𝑆𝑡𝑟𝑎𝑖𝑛, , Hence, Young’s modulus for rubber is less than it is for steel., Shear modulus is the ratio of the applied stress to the change in the shape of a body. The, stretching of a coil changes its shape. Hence, shear modulus of elasticity is involved in, this process., , Question 9.5:, Two wires of diameter 0.25 cm, one made of steel and the other made of brass are, loaded as shown in Fig. 9.13. The unloaded length of steel wire is 1.5 m and that of, brass wire is 1.0 m. Compute the elongations of the steel and the brass wires., , Fig. 9.13, Answer 9.5:, Elongation of the steel wire = 1.49 × 10–4 m, , 4

Page 5 :
Elongation of the brass wire = 1.3 × 10–4 m, Diameter of the wires, d = 0.25 m, Hence, the radius of the wires, r = d/2= 0.125 cm, Length of the steel wire, L1 = 1.5 m, Length of the brass wire, L2 = 1.0 m, Total force exerted on the steel wire:, F1 = (4 + 6) g = 10 × 9.8 = 98 N, Young’s modulus for steel:, , Where,, , 5

Page 6 :
Elongation of the steel wire = 1.49 × 10–4 m, Elongation of the brass wire = 1.3 × 10–4 m, , Question 9.6:, The edge of an aluminium cube is 10 cm long. One face of the cube is firmly fixed to a, vertical wall. A mass of 100 kg is then attached to the opposite face of the cube. The, shear modulus of aluminium is 25 GPa. What is the vertical deflection of this face?, Answer 9.6:, Edge of the aluminium cube, L = 10 cm = 0.1 m, The mass attached to the cube, m = 100 kg, Shear modulus (η) of aluminium = 25 GPa = 25 × 109 Pa, , 6

Page 7 :
Shear modulus, η, , Where,, F = Applied force = mg = 100 × 9.8 = 980 N, A = Area of one of the faces of the cube = 0.1 × 0.1 = 0.01 m2, ΔL = Vertical deflection of the cube, , = 3.92 × 10–7 m, The vertical deflection of this face of the cube is 3.92 ×10–7 m., , Question 9.7:, Four identical hollow cylindrical columns of mild steel support a big structure of mass, 50,000 kg. The inner and outer radii of each column are 30 cm and 60 cm respectively., Assuming the load distribution to be uniform, calculate the compressional strain of each, column., Answer 9.7:, Mass of the big structure, M = 50,000 kg, Inner radius of the column, r = 30 cm = 0.3 m, Outer radius of the column, R = 60 cm = 0.6 m, , 7

Page 8 :
Young’s modulus of steel, Y = 2 × 1011 Pa, Total force exerted, F = Mg = 50000 × 9.8 N, Stress = Force exerted on a single column, Young’s modulus, Y =, , = 122500 N, , 𝑆𝑡𝑟𝑒𝑠𝑠, 𝑆𝑡𝑟𝑎𝑖𝑛, , Where,, Area, A = π (R2 – r2) = π ((0.6)2 – (0.3)2), = 7.22 × 10–7, , Hence, the compressional strain of each column is 7.22 × 10–7., , Question 9.8:, A piece of copper having a rectangular cross-section of 15.2 mm × 19.1 mm is pulled in, tension with 44,500 N force, producing only elastic deformation. Calculate the resulting, strain?, Answer 9.8:, Length of the piece of copper, l = 19.1 mm = 19.1 × 10–3 m, Breadth of the piece of copper, b = 15.2 mm = 15.2 × 10–3 m, Area of the copper piece:, A = l × b = 19.1 × 10–3 × 15.2 × 10–3 = 2.9 × 10–4 m2, Tension force applied on the piece of copper, F = 44500 N, , 8

Page 9 :
Modulus of elasticity of copper, η = 42 × 109 N/m2, , Modulus of elasticity, η, , = 3.65 × 10–3, , Question 9.9:, A steel cable with a radius of 1.5 cm supports a chairlift at a ski area. If the maximum, stress is not to exceed 108 N m–2, what is the maximum load the cable can support?, , 9

Page 10 :
Question 9.10:, A rigid bar of mass 15 kg is supported symmetrically by three wires each 2.0 m long., Those at each end are of copper and the middle one is of iron. Determine the ratio of their, diameters if each is to have the same tension., Answer 9.10:, The tension force acting on each wire is the same. Thus, the extension in each case is, the same. Since the wires are of the same length, the strain will also be the same., The relation for Young’s modulus is given as:, , Where,, F = Tension force, A = Area of cross-section, , 10

Page 11 :
Question 9.11:, A 14.5 kg mass, fastened to the end of a steel wire of unstretched length 1.0 m, is whirled, in a vertical circle with an angular velocity of 2 rev/s at the bottom of the circle. The, cross-sectional area of the wire is 0.065 cm2. Calculate the elongation of the wire when, the mass is at the lowest point of its path., Answer 9.11:, Mass, m = 14.5 kg, Length of the steel wire, l = 1.0 m, Angular velocity, ω = 2 rev/s, Cross-sectional area of the wire, a = 0.065 cm2, Let δl be the elongation of the wire when the mass is at the lowest point of its path., When the mass is placed at the position of the vertical circle, the total force on the mass, is:, F = mg + mlω2, = 14.5 × 9.8 + 14.5 × 1 × (2)2 = 200.1 N, , Young’s modulus for steel = 2 × 1011 Pa, , Hence, the elongation of the wire is 1.539 × 10–4 m., , 11

Page 12 :
Question 9.12:, Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre,, Pressure increase = 100.0 atm (1 atm = 1.013 × 105 Pa), Final volume = 100.5 litre., Compare the bulk modulus of water with that of air (at constant temperature). Explain in, simple terms why the ratio is so large., , Answer 9.12:, Initial volume, V1 = 100.0l = 100.0 × 10 –3 m3, Final volume, V2 = 100.5 l = 100.5 ×10 –3 m3, Increase in volume, ΔV = V2 – V1 = 0.5 × 10–3 m3, Increase in pressure, Δp = 100.0 atm = 100 × 1.013 × 105 Pa, , 12

Page 13 :
Question 9.13:, What is the density of water at a depth where pressure is 80.0 atm, given that its density, at the surface is 1.03 × 103 kg m–3?, Answer 9.13:, Let the given depth be h., Pressure at the given depth, p = 80.0 atm = 80 × 1.01 × 105 Pa, Density of water at the surface, ρ1 = 1.03 × 103 kg m–3, Let ρ2 be the density of water at the depth h., Let V1 be the volume of water of mass m at the surface., Let V2 be the volume of water of mass m at the depth h., Let ΔV be the change in volume., , 13

Page 14 :
For equations (i) and (ii), we get:, , Therefore, the density of water at the given depth (h) is 1.034 × 103 kg m–3., , Question 9.14:, Compute the fractional change in volume of a glass slab, when subjected to a hydraulic, pressure of 10 atm., Answer 9.14:, Hydraulic pressure exerted on the glass slab, p = 10 atm = 10 × 1.013 × 105 Pa, Bulk modulus of glass, B = 37 × 109 Nm–2, , 14

Page 15 :
Where,, = Fractional change in volume, , Hence, the fractional change in the volume of the glass slab is 2.73 × 10–5., , Question 9.15:, Determine the volume contraction of a solid copper cube, 10 cm on an edge, when, subjected to a hydraulic pressure of 7.0 ×106 Pa., , 15

Page 16 :
Original volume of the cube, V = l3, , Therefore, the volume contraction of the solid copper cube is 5 × 10–2 cm–3., Question 9.16:, How much should the pressure on a litre of water be changed to compress it by 0.10%?, Answer 9.16:, Volume of water, V = 1 L, It is given that water is to be compressed by 0.10%., , Therefore, the pressure on water should be 2.2 ×106 Nm–2., , 16

Page 17 :
(www.tiwariacademy.com), (Class – XI), , Question 9.17:, Anvils made of single crystals of diamond, with the shape as shown in Fig. 9.14, are used, to investigate behaviour of materials under very high pressures. Flat faces at the narrow, end of the anvil have a diameter of 0.50 mm, and the wide ends are subjected to a, compressional force of 50,000 N. What is the pressure at the tip of the anvil?, , Fig. 9.14, Answer 9.17:, Diameter of the cones at the narrow ends, d = 0.50 mm = 0.5 × 10–3 m, , Compressional force, F = 50000 N, Pressure at the tip of the anvil:, , Therefore, the pressure at the tip of the anvil is 2.55 × 1011 Pa., , 17

Page 18 :
Question 9.18:, A rod of length 1.05 m having negligible mass is supported at its ends by two wires of, steel (wire A) and aluminium (wire B) of equal lengths as shown in Fig. 9.15. The, crosssectional areas of wires A and B are 1.0 mm2 and 2.0 mm2, respectively. At what, point along the rod should a mass m be suspended in order to produce (a) equal stresses, and (b) equal strains in both steel and aluminium wires., , Fig. 9.15, Answer 9.18:, (a) 0.7 m from the steel-wire end 0.432 m from the steel-wire end, Cross-sectional area of wire A, a1 = 1.0 mm2 = 1.0 × 10–6 m2, Cross-sectional area of wire B, a2 = 2.0 mm2 = 2.0 × 10–6 m2, Young’s modulus for steel, Y1 = 2 × 1011 Nm–2, Young’s modulus for aluminium, Y2 = 7.0 ×1010 Nm–2, Let a small mass m be suspended to the rod at a distance y from the end where wire A is, attached., , If the two wires have equal stresses, then:, , Where,, , 18

Page 19 :
F1 = Force exerted on the steel wire, F2 = Force exerted on the aluminum wire, , The situation is shown in the following figure., , Taking torque about the point of suspension, we have:, , Using equations (i) and (ii), we can write:, , In order to produce an equal stress in the two wires, the mass should be suspended at a, distance of 0.7 m from the end where wire A is attached., , 19

Page 20 :
If the strain in the two wires is equal, then:, , Taking torque about the point where mass m, is suspended at a distance y1 from the side, where wire A attached, we get:, F1y1 = F2 (1.05 – y1), , … (iii), Using equations (iii) and (iv), we get:, , In order to produce an equal strain in the two wires, the mass should be suspended at a, distance of 0.432 m from the end where wire A is attached., , 20

Page 21 :
Question 9.19:, A mild steel wire of length 1.0 m and cross-sectional area 0.50 × 10–2 cm2 is stretched,, well within its elastic limit, horizontally between two pillars. A mass of 100 g is, suspended from the mid-point of the wire. Calculate the depression at the midpoint., Answer 9.19:, , Original length = XZ, Depression = l, The length after mass m, is attached to the wire = XO + OZ, Increase in the length of the wire:, Δl = (XO + OZ) – XZ, Where,, , 21

Page 22 :
XO = OZ =, , Let T be the tension in the wire., mg = 2T cosθ, Using the figure, it can be written as:, , Expanding the expression and eliminating the higher terms:, , 22

Page 23 :
Young’s modulus of steel, Y =, , Hence, the depression at the midpoint is 0.0106 m., , 23

Page 24 :
Question 9.20:, Two strips of metal are riveted together at their ends by four rivets, each of diameter 6.0, mm. What is the maximum tension that can be exerted by the riveted strip if the shearing, stress on the rivet is not to exceed 6.9 × 107 Pa? Assume that each rivet is to carry one, quarter of the load., , Answer 9.20:, Diameter of the metal strip, d = 6.0 mm = 6.0 × 10–3 m, , 24

Page 25 :
Question 9.21:, The Marina trench is located in the Pacific Ocean, and at one place it is nearly eleven km, beneath the surface of water. The water pressure at the bottom of the trench is about 1.1, × 108 Pa. A steel ball of initial volume 0.32 m3 is dropped into the ocean and falls to the, bottom of the trench. What is the change in the volume of the ball when it reaches to the, bottom?, Answer 9.21:, , Therefore, the change in volume of the ball on reaching the bottom of the trench is, 2.2 × 10-4 m3., , 25