Page 3 :
This page, intentionally left, blank
Page 5 : Copyright © 2009, New Age International (P) Ltd., Publishers, Published by New Age International (P) Ltd., Publishers, All rights reserved., No part of this ebook may be reproduced in any form, by photostat, microfilm,, xerography, or any other means, or incorporated into any information retrieval, system, electronic or mechanical, without the written permission of the publisher., All inquiries should be emailed to
[email protected], , ISBN (13) : 978-81-224-2707-3, , PUBLISHING FOR ONE WORLD, , NEW AGE INTERNATIONAL (P) LIMITED, PUBLISHERS, 4835/24, Ansari Road, Daryaganj, New Delhi - 110002, Visit us at www.newagepublishers.com
Page 6 :
Preface, This book is based on the experience and the lecture notes of the authors while teaching, Numerical Analysis for almost four decades at the Indian Institute of Technology, New Delhi., This comprehensive textbook covers material for one semester course on Numerical, Methods of Anna University. The emphasis in the book is on the presentation of fundamentals, and theoretical concepts in an intelligible and easy to understand manner. The book is written, as a textbook rather than as a problem/guide book. The textbook offers a logical presentation, of both the theory and techniques for problem solving to motivate the students for the study, and application of Numerical Methods. Examples and Problems in Exercises are used to explain, each theoretical concept and application of these concepts in problem solving. Answers for, every problem and hints for difficult problems are provided to encourage the students for selflearning., The authors are highly grateful to Prof. M.K. Jain, who was their teacher, colleague, and co-author of their earlier books on Numerical Analysis. With his approval, we have freely, used the material from our book, Numerical Methods for Scientific and Engineering, Computation, published by the same publishers., This book is the outcome of the request of Mr. Saumya Gupta, Managing Director,, New Age International Publishers, for writing a good book on Numerical Methods for Anna, University. The authors are thankful to him for following it up until the book is complete., The first author is thankful to Dr. Gokaraju Gangaraju, President of the college,, Prof. P.S. Raju, Director and Prof. Jandhyala N. Murthy, Principal, Gokaraju Rangaraju, Institute of Engineering and Technology, Hyderabad for their encouragement during the, preparation of the manuscript., The second author is thankful to the entire management of Manav Rachna Educational, Institutions, Faridabad and the Director-Principal of Manav Rachna College of Engineering,, Faridabad for providing a congenial environment during the writing of this book., S.R.K. Iyengar, R.K. Jain
Page 7 :
This page, intentionally left, blank
Page 8 :
Contents, Preface, , (v), , 1. SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , 1–62, , 1.1 Solution of Algebraic and Transcendental Equations, 1, 1.1.1, , Introduction, 1, , 1.1.2, , Initial Approximation for an Iterative Procedure, 4, , 1.1.3, , Method of False Position, 6, , 1.1.4, , Newton-Raphson Method, 11, , 1.1.5, , General Iteration Method, 15, , 1.1.6, , Convergence of Iteration Methods, 19, , 1.2 Linear System of Algebraic Equations, 25, 1.2.1, , Introduction, 25, , 1.2.2, , Direct Methods, 26, 1.2.2.1 Gauss Elimination Method, 28, 1.2.2.2 Gauss-Jordan Method, 33, 1.2.2.3 Inverse of a Matrix by Gauss-Jordan Method, 35, , 1.2.3, , Iterative Methods, 41, 1.2.3.1 Gauss-Jacobi Iteration Method, 41, 1.2.3.2 Gauss-Seidel Iteration Method, 46, , 1.3 Eigen Value Problems, 52, 1.3.1, , Introduction, 52, , 1.3.2, , Power Method, 53, , 1.4 Answers and Hints, 59, 2. INTERPOLATION AND APPROXIMATION, 2.1 Introduction, 63, 2.2 Interpolation with Unevenly Spaced Points, 64, 2.2.1 Lagrange Interpolation, 64, 2.2.2 Newton’s Divided Difference Interpolation, 72, 2.3 Interpolation with Evenly Spaced Points, 80, 2.3.1 Newton’s Forward Difference Interpolation Formula, 89, 2.3.2 Newton’s Backward Difference Interpolation Formula, 92, 2.4 Spline Interpolation and Cubic Splines, 99, 2.5 Answers and Hints, 108, , 63–108
Page 9 :
3. NUMERICAL DIFFERENTIATION AND INTEGRATION, , 109–179, , 3.1 Introduction, 109, 3.2 Numerical Differentiation, 109, 3.2.1, , Methods Based on Finite Differences, 109, 3.2.1.1 Derivatives Using Newton’s Forward Difference Formula, 109, 3.2.1.2 Derivatives Using Newton’s Backward Difference Formula, 117, 3.2.1.3 Derivatives Using Newton’s Divided Difference Formula, 122, , 3.3 Numerical Integration, 128, 3.3.1, , Introduction, 128, , 3.3.2, , Integration Rules Based on Uniform Mesh Spacing, 129, 3.3.2.1 Trapezium Rule, 129, 3.3.2.2 Simpson’s 1/3 Rule, 136, 3.3.2.3 Simpson’s 3/8 Rule, 144, 3.3.2.4 Romberg Method, 147, , 3.3.3, , Integration Rules Based on Non-uniform Mesh Spacing, 159, 3.3.3.1 Gauss-Legendre Integration Rules, 160, , 3.3.4, , Evaluation of Double Integrals, 169, 3.3.4.1 Evaluation of Double Integrals Using Trapezium Rule, 169, 3.3.4.2 Evaluation of Double Integrals by Simpson’s Rule, 173, , 3.4 Answers and Hints, 177, 4. INITIAL VALUE PROBLEMS FOR ORDINARY, DIFFERENTIAL EQUATIONS, 4.1 Introduction, 180, 4.2 Single Step and Multi Step Methods, 182, 4.3 Taylor Series Method, 184, 4.3.1 Modified Euler and Heun’s Methods, 192, 4.4 Runge-Kutta Methods, 200, 4.5 System of First Order Initial Value Problems, 207, 4.5.1 Taylor Series Method, 208, 4.5.2 Runge-Kutta Fourth Order Method, 208, 4.6 Multi Step Methods and Predictor-Corrector Methods, 216, 4.6.1 Predictor Methods (Adams-Bashforth Methods), 217, 4.6.2 Corrector Methods, 221, 4.6.2.1 Adams-Moulton Methods, 221, 4.6.2.2 Milne-Simpson Methods, 224, 4.6.2.3 Predictor-Corrector Methods, 225, 4.7 Stability of Numerical Methods, 237, 4.8 Answers and Hints, 238, , 180–240
Page 10 :
5. BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL, EQUATIONS AND INITIAL & BOUNDARY VALUE PROBLEMS IN, PARTIAL DIFFERENTIAL EQUATIONS, , 241–309, , 5.1 Introduction, 241, 5.2 Boundary Value Problems Governed by Second Order Ordinary Differential Equations,, 241, 5.3 Classification of Linear Second Order Partial Differential Equations, 250, 5.4 Finite Difference Methods for Laplace and Poisson Equations, 252, 5.5 Finite Difference Method for Heat Conduction Equation, 274, 5.6 Finite Difference Method for Wave Equation, 291, 5.7 Answers and Hints, 308, Bibliography, , 311–312, , Index, , 313–315
Page 11 :
This page, intentionally left, blank
Page 12 :
Solution of Equations and, Eigen Value Problems, , 1.1, , SOLUTION OF ALGEBRAIC AND TRANSCENDENTAL EQUATIONS, , 1.1.1 Introduction, A problem of great importance in science and engineering is that of determining the roots/, zeros of an equation of the form, f(x) = 0,, , (1.1), , A polynomial equation of the form, f(x) = Pn(x) = a0xn + a1xn–1 + a2xn–2 + ... + an –1x + an = 0, , (1.2), , is called an algebraic equation. An equation which contains polynomials, exponential functions,, logarithmic functions, trigonometric functions etc. is called a transcendental equation., For example,, 3x3 – 2x2 – x – 5 = 0,, , x4 – 3x2 + 1 = 0,, , x2 – 3x + 1 = 0,, , are algebraic (polynomial) equations, and, xe2x – 1 = 0,, , cos x – xex = 0,, , tan x = x, , are transcendental equations., We assume that the function f(x) is continuous in the required, interval., , f(x), , We define the following., Root/zero A number α, for which f(α) ≡ 0 is called a root of the, equation f(x) = 0, or a zero of f(x). Geometrically, a root of an equation f(x) = 0 is the value of x at which the graph of the equation y =, f(x) intersects the x-axis (see Fig. 1.1)., , 1, , O, , , , Fig. 1.1 ‘Root of f(x) = 0’, , x
Page 13 :
2, , NUMERICAL METHODS, , Simple root A number α is a simple root of f(x) = 0, if f(α) = 0 and f ′(α) ≠ 0. Then, we can, write f(x) as, f(x) = (x – α) g(x), g(α) ≠ 0., For example, since (x – 1) is a factor of f(x) =, , x3, , (1.3), + x – 2 = 0, we can write, , f(x) = (x – 1)(x2 + x + 2) = (x – 1) g(x), g(1) ≠ 0., Alternately, we find f(1) = 0, f ′(x) = 3x2 + 1, f ′(1) = 4 ≠ 0. Hence, x = 1 is a simple root of, f(x) = x3 + x – 2 = 0., Multiple root A number α is a multiple root, of multiplicity m, of f(x) = 0, if, f(α) = 0, f ′(α) = 0, ..., f (m –1) (α) = 0, and f (m) (α) ≠ 0., , (1.4), , Then, we can write f(x) as, f(x) = (x – α)m g(x), g(α) ≠ 0., For example, consider the equation f(x) = x3 – 3x2 + 4 = 0. We find, f(2) = 8 – 12 + 4 = 0, f ′(x) = 3x2 – 6x, f ′(2) = 12 – 12 = 0,, f ″(x) = 6x – 6, f ″(2) = 6 ≠ 0., Hence, x = 2 is a multiple root of multiplicity 2 (double root) of f(x) = x3 – 3x2 + 4 = 0., We can write, , f(x) = (x – 2)2 (x + 1) = (x – 2)2 g(x), g(2) = 3 ≠ 0., , In this chapter, we shall be considering the case of simple roots only., Remark 1 A polynomial equation of degree n has exactly n roots, real or complex, simple or, multiple, where as a transcendental equation may have one root, infinite number of roots or, no root., We shall derive methods for finding only the real roots., The methods for finding the roots are classified as (i) direct methods, and (ii) iterative, methods., Direct methods These methods give the exact values of all the roots in a finite number of, steps (disregarding the round-off errors). Therefore, for any direct method, we can give the, total number of operations (additions, subtractions, divisions and multiplications). This number, is called the operational count of the method., For example, the roots of the quadratic equation ax2 + bx + c = 0, a ≠ 0, can be obtained, using the method, , LM, N, , OP, Q, , 1, − b ± b2 − 4 ac ., 2a, For this method, we can give the count of the total number of operations., x=, , There are direct methods for finding all the roots of cubic and fourth degree polynomials. However, these methods are difficult to use., Direct methods for finding the roots of polynomial equations of degree greater than 4 or, transcendental equations are not available in literature.
Page 14 :
3, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , Iterative methods These methods are based on the idea of successive approximations. We, start with one or two initial approximations to the root and obtain a sequence of approximations x0, x1, ..., xk, ..., which in the limit as k → ∞, converge to the exact root α. An iterative, method for finding a root of the equation f(x) = 0 can be obtained as, xk + 1 = φ(xk),, , k = 0, 1, 2, ....., , (1.5), , This method uses one initial approximation to the root x0 . The sequence of approximations is given by, x1 = φ(x0),, , x2 = φ(x1),, , x3 = φ (x2), ....., , The function φ is called an iteration function and x0 is called an initial approximation., If a method uses two initial approximations x0, x1, to the root, then we can write the, method as, xk + 1 = φ(xk – 1, xk),, , k = 1, 2, ....., , (1.6), , Convergence of iterative methods The sequence of iterates, {xk}, is said to converge to the, exact root α, if, lim xk = α,, , k→∞, , or, , lim | xk – α | = 0., , (1.7), , k→∞, , The error of approximation at the kth iterate is defined as εk = xk – α. Then, we can, write (1.7) as, , lim | error of approximation | = lim | xk – α | = lim | εk | = 0., , k→∞, , k→∞, , k→∞, , Remark 2 Given one or two initial approximations to the root, we require a suitable iteration, function φ for a given function f(x), such that the sequence of iterates, {xk}, converge to the, exact root α. Further, we also require a suitable criterion to terminate the iteration., Criterion to terminate iteration procedure Since, we cannot perform infinite number of, iterations, we need a criterion to stop the iterations. We use one or both of the following, criterion:, (i) The equation f(x) = 0 is satisfied to a given accuracy or f(xk) is bounded by an error, tolerance ε., | f (xk) | ≤ ε., , (1.8), , (ii) The magnitude of the difference between two successive iterates is smaller than a given, accuracy or an error bound ε., | xk + 1 – xk | ≤ ε., , (1.9), , Generally, we use the second criterion. In some very special problems, we require to use, both the criteria., For example, if we require two decimal place accuracy, then we iterate until | xk+1 – xk |, < 0.005. If we require three decimal place accuracy, then we iterate until | xk+1 – xk | < 0.0005., As we have seen earlier, we require a suitable iteration function and suitable initial, approximation(s) to start the iteration procedure. In the next section, we give a method to find, initial approximation(s).
Page 15 :
4, , NUMERICAL METHODS, , 1.1.2 Initial Approximation for an Iterative Procedure, For polynomial equations, Descartes’ rule of signs gives the bound for the number of positive, and negative real roots., (i) We count the number of changes of signs in the coefficients of Pn(x) for the equation f(x) =, Pn(x) = 0. The number of positive roots cannot exceed the number of changes of signs. For, example, if there are four changes in signs, then the equation may have four positive roots or, two positive roots or no positive root. If there are three changes in signs, then the equation, may have three positive roots or definitely one positive root. (For polynomial equations with, real coefficients, complex roots occur in conjugate pairs.), (ii) We write the equation f(– x) = Pn(– x) = 0, and count the number of changes of signs in the, coefficients of Pn(– x). The number of negative roots cannot exceed the number of changes of, signs. Again, if there are four changes in signs, then the equation may have four negative, roots or two negative roots or no negative root. If there are three changes in signs, then the, equation may have three negative roots or definitely one negative root., We use the following theorem of calculus to determine an initial approximation. It is, also called the intermediate value theorem., Theorem 1.1 If f(x) is continuous on some interval [a, b] and f(a)f(b) < 0, then the equation, f(x) = 0 has at least one real root or an odd number of real roots in the interval (a, b)., This result is very simple to use. We set up a table of values of f (x) for various values, of x. Studying the changes in signs in the values of f (x), we determine the intervals in which, the roots lie. For example, if f (1) and f (2) are of opposite signs, then there is a root in the, interval (1, 2)., Let us illustrate through the following examples., Example 1.1 Determine the maximum number of positive and negative roots and intervals of, length one unit in which the real roots lie for the following equations., (i) 8x3 – 12x2 – 2x + 3 = 0, , (ii) 3x3 – 2x2 – x – 5 = 0., , Solution, f(x) = 8x3 – 12x2 – 2x + 3 = 0., , (i) Let, , The number of changes in the signs of the coefficients (8, – 12, – 2, 3) is 2. Therefore, the, equation has 2 or no positive roots. Now, f(– x) = – 8x3 – 12x2 + 2x + 3. The number of changes, in signs in the coefficients (– 8, – 12, 2, 3) is 1. Therefore, the equation has one negative root., We have the following table of values for f(x), (Table 1.1)., Table 1.1. Values of f (x), Example 1.1(i )., x, f(x), , –2, , –1, , 0, , 1, , 2, , 3, , – 105, , – 15, , 3, , –3, , 15, , 105, , Since, f(– 1) f(0) < 0, there is a root in the interval (– 1, 0),, f(0) f(1) < 0, there is a root in the interval (0, 1),, f(1) f(2) < 0, there is a root in the interval (1, 2).
Page 16 :
5, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , Therefore, there are three real roots and the roots lie in the intervals (– 1, 0), (0, 1), (1, 2)., f(x) = 3x2 – 2x2 – x – 5 = 0., , (ii) Let, , The number of changes in the signs of the coefficients (3, – 2, – 1, – 5) is 1. Therefore,, the equation has one positive root. Now, f(– x) = – 3x2 – 2x2 + x – 5. The number of changes in, signs in the coefficients (– 3, – 2, 1, – 5) is 2. Therefore, the equation has two negative or no, negative roots., We have the table of values for f (x), (Table 1.2)., Table 1.2. Values of f (x ), Example 1.1(ii )., x, f(x), , –3, , –2, , –1, , 0, , 1, , 2, , 3, , – 101, , – 35, , –9, , –5, , –5, , 9, , 55, , From the table, we find that there is one real positive root in the interval (1, 2). The, equation has no negative real root., Example 1.2 Determine an interval of length one unit in which the negative real root, which is, smallest in magnitude lies for the equation 9x3 + 18x2 – 37x – 70 = 0., Solution Let f(x) = 9x3 + 18x2 – 37x – 70 = 0. Since, the smallest negative real root in magnitude is required, we form a table of values for x < 0, (Table 1.3)., Table 1.3. Values of f (x ), Example 1.2., x, f(x), , –5, , –4, , –3, , –2, , –1, , 0, , – 560, , – 210, , – 40, , 4, , – 24, , – 70, , Since, f(– 2)f(– 1) < 0, the negative root of smallest magnitude lies in the interval, (– 2, –1)., Example 1.3 Locate the smallest positive root of the equations, (i) xex = cos x., (ii) tan x = 2x., Solution, (i) Let f(x) = xex – cos x = 0. We have f(0) = – 1, f(1) = e – cos 1 = 2.718 – 0.540 = 2.178. Since,, f(0) f(1) < 0, there is a root in the interval (0, 1)., (ii) Let f(x) = tan x – 2x = 0. We have the following function values., f(0) = 0, f(0.1) = – 0.0997, f(0.5) = – 0.4537,, f(1) = – 0.4426, f(1, 1) = – 0.2352, f(1.2) = 0.1722., Since, f(1.1) f(1.2) < 0, the root lies in the interval (1.1, 1.2)., Now, we present some iterative methods for finding a root of the given algebraic or, transcendental equation., We know from calculus, that in the neighborhood of a point on a curve, the curve can be, approximated by a straight line. For deriving numerical methods to find a root of an equation
Page 17 :
6, , NUMERICAL METHODS, , f(x) = 0, we approximate the curve in a sufficiently small interval which contains the root, by, a straight line. That is, in the neighborhood of a root, we approximate, f(x) ≈ ax + b, a ≠ 0, where a and b are arbitrary parameters to be determined by prescribing two appropriate, conditions on f(x) and/or its derivatives. Setting ax + b = 0, we get the next approximation to, the root as x = – b/a. Different ways of approximating the curve by a straight line give different, methods. These methods are also called chord methods. Method of false position (also called, regula-falsi method) and Newton-Raphson method fall in this category of chord methods., 1.1.3 Method of False Position, The method is also called linear interpolation method or chord method or regula-falsi method., At the start of all iterations of the method, we require the interval in which the root, lies. Let the root of the equation f(x) = 0, lie in the interval (xk–1, xk), that is, fk–1 fk < 0, where, f(xk–1) = fk–1, and f(xk) = fk. Then, P(xk–1, fk–1), Q(xk, fk) are points on the curve f(x) = 0. Draw a, straight line joining the points P and Q (Figs. 1.2a, b). The line PQ is taken as an approximation of the curve in the interval [xk–1, xk]. The equation of the line PQ is given by, , y − fk, x − xk ., =, fk −1 − fk x k −1 − x k, The point of intersection of this line PQ with the x-axis is taken as the next approximation to the root. Setting y = 0, and solving for x, we get, x = xk –, , FG x, Hf, , k −1, k −1, , − xk, − fk, , IJ, K, , fk = x k –, , FG x, Hf, , k, k, , IJ, K, , − x k −1, f., − fk −1 k, , The next approximation to the root is taken as, xk+1 = xk –, , FG x, Hf, , k, k, , IJ, K, , − x k −1, fk., − fk −1, , (1.10), , Simplifying, we can also write the approximation as, xk+1 =, , x k ( fk − fk −1 ) − ( x k − x k −1 )fk, x f − x k fk −1, = k −1 k, , k = 1, 2, ... (1.11), fk − fk −1, fk − fk −1, , Therefore, starting with the initial interval (x0, x1), in which the root lies, we compute, x2 =, , x 0 f1 − x1 f0, ., f1 − f0, , Now, if f(x0) f(x2) < 0, then the root lies in the interval (x0, x2). Otherwise, the root lies in, the interval (x2, x1). The iteration is continued using the interval in which the root lies, until, the required accuracy criterion given in Eq.(1.8) or Eq.(1.9) is satisfied., Alternate derivation of the method, Let the root of the equation f(x) = 0, lie in the interval (xk–1, xk). Then, P(xk–1, fk–1), Q(xk, fk), are points on the curve f(x) = 0. Draw the chord joining the points P and Q (Figs. 1.2a, b). We
Page 18 :
7, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , approximate the curve in this interval by the chord, that is, f(x) ≈ ax + b. The next approximation, to the root is given by x = – b/a. Since the chord passes through the points P and Q, we get, fk–1 = axk–1 + b,, , and, , fk = axk + b., , Subtracting the two equations, we get, fk – fk–1 = a(xk – xk – 1), or, , a=, , fk − fk −1, ., x k − x k −1, , The second equation gives b = fk – axk., Hence, the next approximation is given by, xk+1 = –, , b, f − ax k, f, =− k, = xk – k = xk –, a, a, a, , FG x, Hf, , k, k, , IJ, K, , − x k −1, f, − fk −1 k, , which is same as the method given in Eq.(1.10)., y, , y, P, , x3, x2, , O, , x3, x1, , x0, , x0, , Q, , Fig. 1.2a ‘Method of false position’, , x1, , O, , x, , P, , x2, x, , Q, , Fig. 1.2b ‘Method of false position’, , Remark 3 At the start of each iteration, the required root lies in an interval, whose length is, decreasing. Hence, the method always converges., Remark 4 The method of false position has a disadvantage. If the root lies initially in the, interval (x0, x1), then one of the end points is fixed for all iterations. For example, in Fig.1.2a,, the left end point x0 is fixed and the right end point moves towards the required root. Therefore, in actual computations, the method behaves like, xk+1 =, , x0 fk − xk f0, , k = 1, 2, …, f k − f0, , (1.12), , In Fig.1.2b, the right end point x1 is fixed and the left end point moves towards the, required root. Therefore, in this case, in actual computations, the method behaves like, xk+1 =, , x k f1 − x 1 f k, , k = 1, 2, …, f1 − f k, , (1.13), , Remark 5 The computational cost of the method is one evaluation of the function f(x), for, each iteration., Remark 6 We would like to know why the method is also called a linear interpolation method., Graphically, a linear interpolation polynomial describes a straight line or a chord. The linear, interpolation polynomial that fits the data (xk–1, fk–1), (xk, fk) is given by
Page 19 :
8, , NUMERICAL METHODS, , f(x) =, , x − xk, x − x k− 1, f +, f., xk −1 − x k k–1 xk − x k− 1 k, , (We shall be discussing the concept of interpolation polynomials in Chapter 2)., Setting f(x) = 0, we get, ( x − x k− 1 ) f k − ( x − x k ) f k− 1, = 0,, xk − x k − 1, , or, , or, , x(fk – fk–1) = xk–1 fk – xk fk – 1, , x = xk+1 =, , xk − 1 f k − xk f k − 1, ., f k − f k−1, , This gives the next approximation as given in Eq. (1.11)., Example 1.4 Locate the intervals which contain the positive real roots of the equation x3 – 3x, + 1 = 0. Obtain these roots correct to three decimal places, using the method of false position., Solution We form the following table of values for the function f(x)., x, , 0, , 1, , 2, , 3, , f (x), , 1, , –1, , 3, , 19, , There is one positive real root in the interval (0, 1) and another in the interval (1, 2)., There is no real root for x > 2 as f(x) > 0, for all x > 2., First, we find the root in (0, 1). We have, x0 = 0, x1 = 1, f0 = f(x0) = f(0) = 1, f1 = f(x1) = f(1) = – 1., x2 =, , x 0 f1 − x1 f0, 0 −1, =, = 0.5, f(x2) = f(0.5) = – 0.375., f1 − f0, −1−1, , Since, f(0) f(0.5) < 0, the root lies in the interval (0, 0.5)., x3 =, , x0 f2 − x2 f0, 0 − 0.5(1), =, = 0.36364,, − 0.375 − 1, f2 − f0, , f(x3) = f(0.36364) = – 0.04283., , Since, f(0) f(0.36364) < 0, the root lies in the interval (0, 0.36364)., x4 =, , x 0 f3 − x 3 f0 0 − 0.36364(1), = 0.34870, f(x4) = f(0.34870) = – 0.00370., =, f 3 − f0, − 0.04283 − 1, , Since, f(0) f(0.3487) < 0, the root lies in the interval (0, 0.34870)., x5 =, , x 0 f4 − x 4 f0 0 − 0.3487(1), =, = 0.34741, f(x5) = f(0.34741) = – 0.00030., f4 − f0, − 0.00370 − 1, , Since, f(0) f(0.34741) < 0, the root lies in the interval (0, 0.34741)., x6 =, , x 0 f5 − x 5 f0 0 − 0.34741(1), = 0.347306., =, f5 − f0, − 0.0003 − 1
Page 20 :
SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , Now,, , 9, , | x6 – x5 | = | 0.347306 – 0.34741 | ≈ 0.0001 < 0.0005., , The root has been computed correct to three decimal places. The required root can be, taken as x ≈ x6 = 0.347306. We may also give the result as 0.347, even though x6 is more, accurate. Note that the left end point x = 0 is fixed for all iterations., Now, we compute the root in (1, 2). We have, x0 = 1, x1 = 2, f0 = f(x0) = f(1) = – 1, f1 = f(x1) = f(2) = 3., x2 =, , x 0 f1 − x1 f0 3 − 2( − 1), = 1.25, f(x2) = f(1.25) = – 0.796875., =, 3 − ( − 1), f1 − f0, , Since, f(1.25) f(2) < 0, the root lies in the interval (1.25, 2). We use the formula given in Eq.(1.13)., x3 =, , x 2 f1 − x1 f2 1.25(3) − 2( − 0.796875), = 1.407407,, =, 3 − ( − 0.796875), f1 − f2, , f(x3) = f(1.407407) = – 0.434437., Since, f(1.407407) f(2) < 0, the root lies in the interval (1.407407, 2)., x4 =, , x3 f1 − x1 f3 1.407407(3) − 2(− 0.434437), = 1.482367,, =, f1 − f3, 3 − ( − 0.434437), , f(x4) = f(1.482367) = – 0.189730., Since f(1.482367) f(2) < 0, the root lies in the interval (1.482367, 2)., x5 =, , x4 f1 − x1 f4 1.482367(3) − 2( − 0.18973), =, = 1.513156,, f1 − f 4, 3 − ( − 0.18973), , f(x5) = f(1.513156) = – 0.074884., Since, f(1.513156) f(2) < 0, the root lies in the interval (1.513156, 2)., x6 =, , x 5 f1 − x1 f5 1.513156(3) − 2( − 0.074884), = 1.525012,, =, 3 − ( − 0.74884), f1 − f5, , f(x6) = f(1.525012) = – 0.028374., Since, f(1.525012) f(2) < 0, the root lies in the interval (1.525012, 2)., x7 =, , x 6 f1 − x1 f6 1.525012(3) − 2( − 0.028374), =, = 1.529462., f1 − f 6, 3 − ( − 0.028374), , f(x7) = f(1.529462) = – 0.010586., Since, f(1.529462) f(2) < 0, the root lies in the interval (1.529462, 2)., x8 =, , x 7 f1 − x1 f7 1.529462(3) − 2( − 0.010586), = 1.531116,, =, 3 − ( − 0.010586), f1 − f7, , f(x8) = f(1.531116) = – 0.003928., Since, f(1.531116) f(2) < 0, the root lies in the interval (1.531116, 2).
Page 21 :
10, , NUMERICAL METHODS, , x9 =, , x 8 f1 − x1 f8 1.531116(3) − 2( − 0.003928), = 1.531729,, =, 3 − ( − 0.003928), f1 − f8, , f(x9) = f(1.531729) = – 0.001454., Since, f(1.531729) f(2) < 0, the root lies in the interval (1.531729, 2)., x10 =, , x 9 f1 − x1 f9 1.531729(3) − 2( − 0.001454), = 1.531956., =, 3 − ( − 0.001454), f1 − f9, , Now, |x10 – x9 | = | 1.531956 – 1.53179 | ≈ 0.000227 < 0.0005., The root has been computed correct to three decimal places. The required root can be, taken as x ≈ x10 = 1.531956. Note that the right end point x = 2 is fixed for all iterations., Example 1.5 Find the root correct to two decimal places of the equation xex = cos x, using the, method of false position., Solution Define f(x) = cos x – xex = 0. There is no negative root for the equation. We have, f(0) = 1, f(1) = cos 1 – e = – 2.17798., A root of the equation lies in the interval (0, 1). Let x0 = 0, x1 = 1. Using the method of, false position, we obtain the following results., x2 =, , x 0 f1 − x1 f0, 0 − 1(1), = 0.31467, f(x2) = f(0.31467) = 0.51986., =, f1 − f0, − 2.17798 − 1, , Since, f(0.31467) f(1) < 0, the root lies in the interval (0.31467, 1). We use the formula given in, Eq.(1.13)., x3 =, , x 2 f1 − x1 f2 0.31467( − 2.17798) − 1(0.51986), = 0.44673,, =, f1 − f2, − 2.17798 − 0.51986, , f(x3) = f(0.44673) = 0.20354., Since, f (0.44673) f(1) < 0, the root lies in the interval (0.44673, 1)., x4 =, , x3 f1 − x1 f3 0.44673(− 2.17798) − 1(0.20354), =, = 0.49402,, − 2.17798 − 0.20354, f1 − f3, , f(x4) = f(0.49402) = 0.07079., Since, f (0.49402) f(1) < 0, the root lies in the interval (0.49402, 1)., x5 =, , x4 f1 − x1 f4 0 . 49402(− 2.17798) − 1(0.07079), =, = 0.50995,, f1 − f4, − 2.17798 − 0.07079, , f(x5) = f(0.50995) = 0.02360., Since, f(0.50995) f(1) < 0, the root lies in the interval (0.50995, 1)., x6 =, , x5 f1 − x1 f5 0.50995(− 2.17798) − 1(0.0236), =, = 0.51520,, − 2.17798 − 0.0236, f1 − f5, , f(x6) = f(0.51520) = 0.00776.
Page 22 :
11, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , Since, f(0.51520) f(1) < 0, the root lies in the interval (0.51520, 1)., x7 =, , x6 f1 − x1 f6 0.5152(− 2.17798) − 1(0.00776), = 0.51692., =, − 2.17798 − 0.00776, f1 − f6, , Now, | x7 – x6 | = | 0.51692 – 0.51520 | ≈ 0.00172 < 0.005., The root has been computed correct to two decimal places. The required root can be, taken as x ≈ x7 = 0.51692., Note that the right end point x = 2 is fixed for all iterations., 1.1.4 Newton-Raphson Method, This method is also called Newton’s method. This method is also a chord method in which we, approximate the curve near a root, by a straight line., Let x0 be an initial approximation to the root, of f(x) = 0. Then, P(x0, f0), where f0 = f(x0), is a point on, the curve. Draw the tangent to the curve at P, (Fig., 1.3). We approximate the curve in the neighborhood of, the root by the tangent to the curve at the point P. The, point of intersection of the tangent with the x-axis is, taken as the next approximation to the root. The, process is repeated until the required accuracy is, obtained. The equation of the tangent to the curve, y = f(x) at the point P(x0, f0) is given by, , y, , P, , O, , x1 x0, , x, , Fig. 1.3 ‘Newton-Raphson method’, , y – f(x0) = (x – x0) f ′(x0), where f ′(x0) is the slope of the tangent to the curve at P. Setting y = 0 and solving for x, we get, x = x0 –, , f ( x0 ), ,, f ′( x 0 ), , f ′(x0) ≠ 0., , The next approximation to the root is given by, x1 = x0 –, , f ( x0 ), , f ′(x0) ≠ 0., f ′( x 0 ), , We repeat the procedure. The iteration method is defined as, xk+1 = xk –, , f ( xk ), , f ′(xk) ≠ 0., f ′( x k ), , (1.14), , This method is called the Newton-Raphson method or simply the Newton’s method., The method is also called the tangent method., Alternate derivation of the method, Let xk be an approximation to the root of the equation f(x) = 0. Let ∆x be an increment in, x such that xk + ∆x is the exact root, that is f(xk + ∆x) ≡ 0.
Page 23 :
12, , NUMERICAL METHODS, , Expanding in Taylor’s series about the point xk, we get, f(xk) + ∆x f ′(xk) +, , ( ∆x ) 2, f ″ (xk) + ... = 0., 2!, , (1.15), , Neglecting the second and higher powers of ∆x, we obtain, f(xk) + ∆x f ′(xk) ≈ 0, or, , ∆x = –, , f ( xk ), ., f ′( x k ), , Hence, we obtain the iteration method, xk+1 = xk + ∆x = xk –, , f ( xk ), , f ′(xk) ≠ 0, k = 0, 1, 2, ..., f ′( x k ), , which is same as the method derived earlier., Remark 7 Convergence of the Newton’s method depends on the initial approximation to the, root. If the approximation is far away from the exact root, the method diverges (see Example, 1.6). However, if a root lies in a small interval (a, b) and x0 ∈ (a, b), then the method converges., Remark 8 From Eq.(1.14), we observe that the method may fail when f ′(x) is close to zero in, the neighborhood of the root. Later, in this section, we shall give the condition for convergence, of the method., Remark 9 The computational cost of the method is one evaluation of the function f(x) and one, evaluation of the derivative f ′(x), for each iteration., Example 1.6 Derive the Newton’s method for finding 1/N, where N > 0. Hence, find 1/17,, using the initial approximation as (i) 0.05, (ii) 0.15. Do the iterations converge ?, Solution Let x =, , 1, , or, N, , 1, 1, 1, = N. Define f(x) =, – N. Then, f ′(x) = – 2 ., x, x, x, , Newton’s method gives, xk+1 = xk –, , f ( xk ), [(1/ x k ) − N ], = xk –, = xk + [xk – Nx k2 ] = 2xk – Nx k2 ., f ′( x k ), [ − 1/ x k2 ], , (i) With N = 17, and x0 = 0.05, we obtain the sequence of approximations, x1 = 2x0 – Nx 02 = 2(0.05) – 17(0.05)2 = 0.0575., x2 = 2x1 – Nx12 = 2(0.0575) – 17(0.0575)2 = 0.058794., x3 = 2x2 – Nx 22 = 2(0.058794) – 17(0.058794)2 = 0.058823., x4 = 2x3 – Nx32 = 2(0.058823) – 17(0.058823)2 = 0.058823., Since, | x4 – x3 | = 0, the iterations converge to the root. The required root is 0.058823., (ii) With N = 17, and x0 = 0.15, we obtain the sequence of approximations, x1 = 2x0 – Nx 02 = 2(0.15) – 17(0.15)2 = – 0.0825.
Page 24 :
13, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , x2 = 2x1 – Nx12 = 2(– 0.0825) – 17(– 0.8025)2 = – 0.280706., x3 = 2x2 – Nx 22 = 2(– 0.280706) – 17(– 0.280706)2 = – 1.900942., x4 = 2x3 – Nx32 = 2(– 1.900942) – 17(– 1.900942)2 = – 65.23275., We find that xk → – ∞ as k increases. Therefore, the iterations diverge very fast. This, shows the importance of choosing a proper initial approximation., Example 1.7 Derive the Newton’s method for finding the qth root of a positive number N, N1/q,, where N > 0, q > 0. Hence, compute 171/3 correct to four decimal places, assuming the initial, approximation as x0 = 2., Solution Let, , x = N1/q, or xq = N. Define f(x) = x q – N. Then, f ′(x) = qx q – 1., , Newton’s method gives the iteration, xk+1 = xk –, , xkq − N, qx kq− 1, , =, , qx kq − x kq + N, qx kq− 1, , =, , ( q − 1) x kq + N, qxkq− 1, , ., , For computing 171/3, we have q = 3 and N = 17. Hence, the method becomes, xk+1 =, , 2x k3 + 17, 3x k2, , , k = 0, 1, 2, ..., , With x0 = 2, we obtain the following results., x1 =, , x2 =, , x3 =, , x4 =, Now,, , 2x 03 + 17, 3x 02, , =, , 2( 8) + 17, = 2.75,, 3( 4 ), , 2 x13 + 17 2(2.75) 3 + 17, =, = 2.582645,, 3 x12, 3(2.75) 2, 2x 23 + 17, 3x 22, , 2x 33 + 17, 3x 32, , =, , =, , 2(2.582645)3 + 17, 3(2.582645) 2, 2(2.571332)3 + 17, 3(2.571332) 2, , = 2.571332,, , = 2.571282., , | x4 – x3 | = | 2.571282 – 2.571332 | = 0.00005., , We may take x ≈ 2.571282 as the required root correct to four decimal places., Example 1.8 Perform four iterations of the Newton’s method to find the smallest positive root, of the equation f(x) = x3 – 5x + 1 = 0., Solution We have f(0) = 1, f(1) = – 3. Since, f(0) f(1) < 0, the smallest positive root lies in the, interval (0, 1). Applying the Newton’s method, we obtain, xk+1 = xk –, , xk3 − 5 x k + 1, 3 x k2 − 5, , =, , 2 x k3 − 1, , 3 x k2 − 5, , , k = 0, 1, 2, ...
Page 25 :
14, , NUMERICAL METHODS, , Let x0 = 0.5. We have the following results., x1 =, x2 =, x3 =, x4 =, , 2 x03 − 1, , 3 x02 − 5, , 2 x13 − 1, , 3 x12 − 5, , 2 x23 − 1, , 3 x22 − 5, , 2 x33 − 1, , 3 x32, , −5, , =, , =, , =, , =, , 2(0.5) 3 − 1, , 3(0.5) 2 − 5, , = 0.176471,, , 2(0.176471) 3 − 1, , 3(0.176471) 2 − 5, , 2(0.201568) 3 − 1, , 3(0.201568) 2 − 5, , 2(0.201640) 3 − 1, , 3(0.201640) 2 − 5, , = 0.201568,, , = 0.201640,, , = 0.201640., , Therefore, the root correct to six decimal places is x ≈ 0.201640., Example 1.9 Using Newton-Raphson method solve x log10 x = 12.34 with x0 = 10., (A.U. Apr/May 2004), Solution Define f(x) = x log10 x – 12.34., Then, , f ′(x) = log10 x +, , 1, = log10 x + 0.434294., log e 10, , Using the Newton-Raphson method, we obtain, xk+1 = xk –, , x k log10 x k − 12.34, , k = 0, 1, 2, ..., log10 x k + 0.434294, , With x0 = 10, we obtain the following results., x1 = x0 –, , 10 log 10 10 − 12.34, x0 log 10 x0 − 12.34, = 10 –, = 11.631465., +, log, x, log 10 0 0.434294, 10 10 + 0.434294, , x2 = x1 –, , x1 log 10 x1 − 12.34, log 10 x1 + 0.434294, , = 11.631465 –, x3 = x2 –, , 11.631465 log 10 11.631465 − 12.34, = 11.594870., log 10 11.631465 + 0.434294, , x2 log 10 x2 − 12.34, log 10 x2 + 0.434294, , = 11.59487 –, , 11.59487 log 10 11.59487 − 12.34, = 11.594854., log 10 11.59487 + 0.434294, , We have | x3 – x2 | = | 11.594854 – 11.594870 | = 0.000016., We may take x ≈ 11.594854 as the root correct to four decimal places.
Page 26 :
15, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , 1.1.5 General Iteration Method, The method is also called iteration method or method of successive approximations or fixed, point iteration method., The first step in this method is to rewrite the given equation f(x) = 0 in an equivalent, form as, x = φ(x)., , (1.16), , There are many ways of rewriting f(x) = 0 in this form., For example, f(x) = x3 – 5x + 1 = 0, can be rewritten in the following forms., x=, , x3 + 1, , x = (5x – 1)1/3, x =, 5, , 5x − 1, , etc., x, , (1.17), , Now, finding a root of f(x) = 0 is same as finding a number α such that α = φ(α), that is,, a fixed point of φ(x). A fixed point of a function φ is a point α such that α = φ(α). This result is, also called the fixed point theorem., Using Eq.(1.16), the iteration method is written as, xk+1 = φ(xk), k = 0, 1, 2, ..., , (1.18), , The function φ(x) is called the iteration function. Starting with the initial approximation x0, we compute the next approximations as, x1 = φ(x0), x2 = φ(x1), x3 = φ(x2),..., The stopping criterion is same as used earlier. Since, there are many ways of writing, f(x) = 0 as x = φ(x), it is important to know whether all or at least one of these iteration, methods converges., Remark 10 Convergence of an iteration method xk+1 = φ(xk), k = 0, 1, 2,..., depends on the, choice of the iteration function φ(x), and a suitable initial approximation x0, to the root., Consider again, the iteration methods given in Eq.(1.17), for finding a root of the equation, f(x) = x3 – 5x + 1 = 0. The positive root lies in the interval (0, 1)., x k3 + 1, , k = 0, 1, 2, ..., 5, With x0 = 1, we get the sequence of approximations as, , (i), , xk+1 =, , (1.19), , x1 = 0.4, x2 = 0.2128, x3 = 0.20193, x4 = 0.20165, x5 = 0.20164., The method converges and x ≈ x5 = 0.20164 is taken as the required approximation to, the root., (ii), , xk+1 = (5xk – 1)1/3, k = 0, 1, 2, ..., , (1.20), , With x0 = 1, we get the sequence of approximations as, x1 = 1.5874, x2 = 1.9072, x3 = 2.0437, x4 = 2.0968,..., which does not converge to the root in (0, 1)., (iii), , xk+1 =, , 5x k − 1, , k = 0, 1, 2, ..., xk, , (1.21)
Page 28 :
17, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , (ii) We have φ(x) = (5x – 1)1/3, φ′(x) =, , 5, , . Now | φ′(x) | < 1, when x is close to 1 and, 3(5x − 1)2/ 3, | φ′(x) | > 1 in the other part of the interval. Convergence is not guaranteed., 5x − 1, 1, , φ′(x) =, . Again, | φ′(x) | < 1, when x is close to, 3/ 2, x, 2x (5x − 1)1/ 2, 1 and | φ′(x) | > 1 in the other part of the interval. Convergence is not guaranteed., , (iii) We have φ(x) =, , Remark 11 Sometimes, it may not be possible to find a suitable iteration function φ(x) by, manipulating the given function f(x). Then, we may use the following procedure. Write, f(x) = 0 as x = x + α f(x) = φ(x), where α is a constant to be determined. Let x0 be an initial, approximation contained in the interval in which the root lies. For convergence, we require, | φ′(x0) | = | 1 + α f′(x0) | < 1., , (1.27), , Simplifying, we find the interval in which α lies. We choose a value for α from this, interval and compute the approximations. A judicious choice of a value in this interval may, give faster convergence., Example 1.10 Find the smallest positive root of the equation x3 – x – 10 = 0, using the general, iteration method., Solution We have, f(x) = x3 – x – 10, f(0) = – 10, f(1) = – 10,, f(2) = 8 – 2 – 10 = – 4, f(3) = 27 – 3 – 10 = 14., Since, f(2) f(3) < 0, the smallest positive root lies in the interval (2, 3)., Write x3 = x + 10, and x = (x + 10)1/3 = φ(x). We define the iteration method as, xk+1 = (xk + 10)1/3., We obtain, , φ′(x) =, , 1, 3( x + 10)2/ 3, , ., , We find | φ′(x) | < 1 for all x in the interval (2, 3). Hence, the iteration converges., Let x0 = 2.5. We obtain the following results., x1 = (12.5)1/3 = 2.3208, x2 = (12.3208)1/3 = 2.3097,, x3 = (12.3097)1/3 = 2.3090, x4 = (12.3090)1/3 = 2.3089., Since,, , | x4 – x3 | = 2.3089 – 2.3090 | = 0.0001, we take the required root as x ≈ 2.3089., , Example 1.11 Find the smallest negative root in magnitude of the equation, 3x4 + x3 + 12x + 4 = 0, using the method of successive approximations., Solution We have, f(x) = 3x4 + x3 + 12x + 4 = 0, f(0) = 4, f(– 1) = 3 – 1 – 12 + 4 = – 6., Since, f(– 1) f(0) < 0, the smallest negative root in magnitude lies in the interval (– 1, 0).
Page 29 :
18, , NUMERICAL METHODS, , Write the given equation as, x(3x3 + x2 + 12) + 4 = 0, and x = –, , 4, = φ(x)., 3 x + x 2 + 12, 3, , The iteration method is written as, xk+1 = –, We obtain, , φ′(x) =, , 4, 3 x k3, , + x k2 + 12, , 4( 9x 2 + 2x ), (3x 3 + x 2 + 12)2, , ., , ., , We find | φ′(x) | < 1 for all x in the interval (– 1, 0). Hence, the iteration converges., Let x0 = – 0.25. We obtain the following results., x1 = –, x2 = –, x3 = –, , 4, 3, , 3(− 0.25) + (− 0.25) 2 + 12, , = – 0.33290,, , 4, 3, , 3( − 0.3329) + ( − 0.3329) 2 + 12, , = – 0.33333,, , 4, = – 0.33333., 3(− 0.33333) + (− 0.33333) 2 + 12, 3, , The required approximation to the root is x ≈ – 0.33333., Example 1.12 The equation f(x) = 3x3 + 4x2 + 4x + 1 = 0 has a root in the interval (– 1, 0)., Determine an iteration function φ(x), such that the sequence of iterations obtained from, xk+1 = φ(xk), x0 = – 0.5, k = 0, 1,..., converges to the root., Solution We illustrate the method given in Remark 10. We write the given equation as, x = x + α (3x3 + 4x2 + 4x + 1) = φ(x), where α is a constant to be determined such that, | φ′(x) | = | 1 + α f ′(x) |, = | 1 + α (9x2 + 8x + 4) | < 1, for all x ∈ (– 1, 0). This condition is also to be satisfied at the initial approximation. Setting x0, = – 0.5, we get, | φ′(x0) | = | 1 + α f ′(x0) | = 1 +, or, , –1<1+, , 9α, < 1 or, 4, , –, , 9α, <1, 4, , 8, < α < 0., 9, , Hence, α takes negative values. The interval for α depends on the initial approximation, x0. Let us choose the value α = – 0.5. We obtain the iteration method as, xk+1 = xk – 0.5 (3xk3 + 4xk2 + 4xk + 1)
Page 30 :
19, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , = – 0.5 (3xk3 + 4xk2 + 2xk + 1) = φ(xk)., Starting with x0 = – 0.5, we obtain the following results., x1 = φ(x0) = – 0.5 (3x03 + 4x02 + 2x0 + 1), = – 0.5 [3(– 0.5)3 + 4(– 0.5)2 + 2(– 0.5) + 1] = – 0.3125., x2 = φ(x1) = – 0.5(3x13 + 4x12 + 2x1 + 1), = – 0.5[3(– 0.3125)3 + 4(– 0.3125)2 + 2(– 0.3125) + 1] = – 0.337036., x3 = φ(x2) = – 0.5(3x23 + 4x22 + 2x2 + 1), = – 0.5[3 (– 0.337036)3 + 4(– 0.337036)2 + 2(– 0.337036) + 1] = – 0.332723., x4 = φ(x3) = – 0.5(3x33 + 4x32 + 2x3 + 1), = – 0.5[3(– 0.332723)3 + 4(– 0.332723)2 + 2(– 0.332723) + 1] = – 0.333435., x5 = φ(x4) = – 0.5(3x43 + 4x42 + 2x4 + 1), = – 0.5[3(– 0.333435)3 + 4(– 0.333435)2 + 2(– 0.333435) + 1] = – 0.333316., Since | x5 – x4 | = | – 0.333316 + 0.333435 | = 0.000119 < 0.0005, the result is correct to, three decimal places., We can take the approximation as x ≈ x5 = – 0.333316. The exact root is x = – 1/3., We can verify that | φ′(xj) | < 1 for all j., 1.1.6 Convergence of the Iteration Methods, We now study the rate at which the iteration methods converge to the exact root, if the initial, approximation is sufficiently close to the desired root., Define the error of approximation at the kth iterate as εk = xk – α, k = 0, 1, 2,..., Definition An iterative method is said to be of order p or has the rate of convergence p, if p is, the largest positive real number for which there exists a finite constant C ≠ 0 , such that, | εk+1 | ≤ C | εk | p., , (1.28), , The constant C, which is independent of k, is called the asymptotic error constant and it, depends on the derivatives of f(x) at x = α., Let us now obtain the orders of the methods that were derived earlier., Method of false position We have noted earlier (see Remark 4) that if the root lies initially, in the interval (x0, x1), then one of the end points is fixed for all iterations. If the left end point, x0 is fixed and the right end point moves towards the required root, the method behaves like, (see Fig.1.2a), xk+1 =, , x0 f k − x k f0, ., f k − f0, , Substituting xk = εk + α, xk+1 = εk+1 + α, x0 = ε0 + α, we expand each term in Taylor’s, series and simplify using the fact that f(α) = 0. We obtain the error equation as, εk+1 = Cε0εk, where C =, , f ′′(α), ., 2 f ′(α)
Page 32 :
21, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , and, , | εk+1 | = | C | | εk |2., , (1.31), , Therefore, Newton’s method is of order 2 or has quadratic rate of convergence., Remark 12 What is the importance of defining the order or rate of convergence of a method?, Suppose that we are using Newton’s method for computing a root of f(x) = 0. Let us assume, that at a particular stage of iteration, the error in magnitude in computing the root is 10–1 =, 0.1. We observe from (1.31), that in the next iteration, the error behaves like C(0.1)2 = C(10–2)., That is, we may possibly get an accuracy of two decimal places. Because of the quadratic, convergence of the method, we may possibly get an accuracy of four decimal places in the next, iteration. However, it also depends on the value of C. From this discussion, we conclude that, both fixed point iteration and regula-falsi methods converge slowly as they have only linear, rate of convergence. Further, Newton’s method converges at least twice as fast as the fixed, point iteration and regula-falsi methods., Remark 13 When does the Newton-Raphson method fail?, (i) The method may fail when the initial approximation x0 is far away from the exact root α, (see Example 1.6). However, if the root lies in a small interval (a, b) and x0 ∈ (a, b), then the, method converges., (ii) From Eq.(1.31), we note that if f ′(α) ≈ 0, and f ″ (x) is finite then C → ∞ and the method, may fail. That is, in this case, the graph of y = f(x) is almost parallel to x-axis at the root α., Remark 14 Let us have a re-look at the error equation. We have defined the error of approximation at the kth iterate as εk = xk – α, k = 0, 1, 2,... From xk+1 = φ(xk), k = 0, 1, 2,... and α = φ(α),, we obtain (see Eq.(1.24)), xk+1 – α = φ(xk) – φ(α) = φ(α + εk) – φ(α), , LM, N, , = φ(α) + φ ′ (α) ε k +, or, where, , OP, Q, , 1, φ ′′(α) ε 2k + ... – φ(α), 2, , εk+1 = a1εk + a2εk2 + ..., , (1.32), , a1 = φ′(α), a2 = (1/2)φ″(α), etc., , The exact root satisfies the equation α = φ(α)., If a1 ≠ 0 that is, φ′(α) ≠ 0, then the method is of order 1 or has linear convergence. For the, general iteration method, which is of first order, we have derived that the condition of convergence is | φ′(x) | < 1 for all x in the interval (a, b) in which the root lies. Note that in this method,, | φ′(x) | ≠ 0 for all x in the neighborhood of the root α., If a1 = φ′(α) = 0, and a2 = (1/2)φ″(α) ≠ 0, then from Eq. (1.32), the method is of order 2 or, has quadratic convergence., Let us verify this result for the Newton-Raphson method. For the Newton-Raphson, method, , Then,, , xk+1 = xk –, , f ( xk ), , we have, f ′ ( xk ), , φ′(x) = 1 –, , [ f ′( x)]2 − f ( x) f ′′( x) f ( x) f ′′( x), =, [ f ′( x)]2, [ f ′ ( x)]2, , φ(x) = x –, , f ( x), ., f ′( x)
Page 33 :
22, , NUMERICAL METHODS, , and, , φ′(α) =, , f (α) f ′′(α), [ f ′(α)] 2, , =0, , since f(α) = 0 and f ′(α) ≠ 0 (α is a simple root)., When, xk → α, f (xk) → 0, we have | φ′(xk) | < 1, k = 1, 2,... and → 0 as n → ∞., Now,, , φ″(x) =, , 1, [f ′(x) {f ′(x) f ″(x) + f(x) f ′″(x)} – 2 f(x) {f ″(x)}2], [ f ′( x)]3, , and, , φ″(α) =, , f ′′(α), ≠ 0., f ′(α), , Therefore, a2 ≠ 0 and the second order convergence of the Newton’s method is verified., , REVIEW QUESTIONS, 1. Define a (i) root, (ii) simple root and (iii) multiple root of an algebraic equation f(x) = 0., Solution, (i) A number α, such that f(α) ≡ 0 is called a root of f(x) = 0., (ii) Let α be a root of f(x) = 0. If f(α) ≡ 0 and f ′(α) ≠ 0, then α is said to be a simple root., Then, we can write f(x) as, f (x) = (x – α) g(x), g(α) ≠ 0., (iii) Let α be a root of f(x) = 0. If, f(α) = 0, f ′(α) = 0,..., f (m–1) (α) = 0, and f (m) (α) ≠ 0,, then, α is said to be a multiple root of multiplicity m. Then, we can write f (x) as, f(x) = (x – α)m g(x), g(α) ≠ 0., 2. State the intermediate value theorem., Solution If f(x) is continuous on some interval [a, b] and f (a)f (b) < 0, then the equation, f(x) = 0 has at least one real root or an odd number of real roots in the interval (a, b)., 3. How can we find an initial approximation to the root of f (x) = 0 ?, Solution Using intermediate value theorem, we find an interval (a, b) which contains, the root of the equation f (x) = 0. This implies that f (a)f(b) < 0. Any point in this interval, (including the end points) can be taken as an initial approximation to the root of f(x) = 0., 4. What is the Descartes’ rule of signs?, Solution Let f (x) = 0 be a polynomial equation Pn(x) = 0. We count the number of, changes of signs in the coefficients of f (x) = Pn(x) = 0. The number of positive roots, cannot exceed the number of changes of signs in the coefficients of Pn(x). Now, we write, the equation f(– x) = Pn(– x) = 0, and count the number of changes of signs in the coefficients of Pn(– x). The number of negative roots cannot exceed the number of changes of, signs in the coefficients of this equation., 5. Define convergence of an iterative method., Solution Using any iteration method, we obtain a sequence of iterates (approximations to the root of f(x) = 0), x1, x2,..., xk,... If
Page 34 :
SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , 23, , lim xk = α, or lim | xk – α | = 0, , k→∞, , k→∞, , where α is the exact root, then the method is said to be convergent., 6. What are the criteria used to terminate an iterative procedure?, Solution Let ε be the prescribed error tolerance. We terminate the iterations when, either of the following criteria is satisfied., (i) | f(xk) | ≤ ε., , (ii) | xk+1 – xk | ≤ ε., , Sometimes, we may use both the criteria., 7. Define the fixed point iteration method to obtain a root of f(x) = 0. When does the method, converge?, Solution Let a root of f(x) = 0 lie in the interval (a, b). Let x0 be an initial approximation, to the root. We write f(x) = 0 in an equivalent form as x = φ(x), and define the fixed point, iteration method as xk+1 = φ(xk), k = 0, 1, 2, … Starting with x0, we obtain a sequence of, approximations x1, x2,..., xk,... such that in the limit as k → ∞, xk → α. The method, converges when | φ′(x) | < 1, for all x in the interval (a, b). We normally check this, condition at x0., 8. Write the method of false position to obtain a root of f(x) = 0. What is the computational, cost of the method?, Solution Let a root of f(x) = 0 lie in the interval (a, b). Let x0, x1 be two initial approximations to the root in this interval. The method of false position is defined by, xk+1 =, , xk − 1 f k − x k f k − 1, , k = 1, 2,..., fk − f k − 1, , The computational cost of the method is one evaluation of f(x) per iteration., 9. What is the disadvantage of the method of false position?, Solution If the root lies initially in the interval (x0, x1), then one of the end points is, fixed for all iterations. For example, in Fig.1.2a, the left end point x0 is fixed and the, right end point moves towards the required root. Therefore, in actual computations, the, method behaves like, xk+1 =, , x0 f k − x k f0, ., f k − f0, , In Fig.1.2b, the right end point x1 is fixed and the left end point moves towards the, required root. Therefore, in this case, in actual computations, the method behaves like, xk+1 =, , x k f1 − x 1 f k, ., f1 − f k, , 10. Write the Newton-Raphson method to obtain a root of f(x) = 0. What is the computational cost of the method?, Solution Let a root of f(x) = 0 lie in the interval (a, b). Let x0 be an initial approximation, to the root in this interval. The Newton-Raphson method to find this root is defined by
Page 35 :
24, , NUMERICAL METHODS, , xk+1 = xk –, , f ( xk ), ,, f ′ ( xk ), , f ′(xk) ≠ 0, k = 0, 1, 2,...,, , The computational cost of the method is one evaluation of f(x) and one evaluation of the, derivative f ′(x) per iteration., 11. Define the order (rate) of convergence of an iterative method for finding the root of an, equation f(x) = 0., Solution Let α be the exact root of f (x) = 0. Define the error of approximation at the kth, iterate as εk = xk – α, k = 0, 1, 2,... An iterative method is said to be of order p or has the, rate of convergence p, if p is the largest positive real number for which there exists a, finite constant C ≠ 0, such that, | εk+1 | ≤ C | εk | p., The constant C, which is independent of k, is called the asymptotic error constant and it, depends on the derivatives of f(x) at x = α., 12. What is the rate of convergence of the following methods: (i) Method of false position,, (ii) Newton-Raphson method, (iii) Fixed point iteration method?, Solution (i) One. (ii) Two. (iii) One., , EXERCISE 1.1, In the following problems, find the root as specified using the regula-falsi method (method of, false position)., 1. Find the positive root of x3 = 2x + 5. (Do only four iterations)., , (A.U. Nov./Dec. 2006), , 2. Find an approximate root of x log10 x – 1.2 = 0., 3. Solve the equation x tan x = – 1, starting with a = 2.5 and b = 3, correct to three decimal, places., 4. Find the root of xex = 3, correct to two decimal places., 5. Find the smallest positive root of x – e– x = 0, correct to three decimal places., 6. Find the smallest positive root of x4 – x – 10 = 0, correct to three decimal places., In the following problems, find the root as specified using the Newton-Raphson method., 7. Find the smallest positive root of x4 – x = 10, correct to three decimal places., 8. Find the root between 0 and 1 of x3 = 6x – 4, correct to two decimal places., 9. Find the real root of the equation 3x = cos x + 1., 10., , (A.U. Nov./Dec. 2006), , Find a root of x log10 x – 1.2 = 0, correct to three decimal places., (A.U. Nov./Dec. 2004), , 11., , Find the root of x = 2 sin x, near 1.9, correct to three decimal places., , 12., , (i) Write an iteration formula for finding, , N where N is a real number., (A.U. Nov./Dec. 2006, A.U. Nov./Dec. 2003), , (ii) Hence, evaluate, , 142 , correct to three decimal places.
Page 36 :
25, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , 13., , (i) Write an iteration formula for finding the value of 1/N, where N is a real number., (ii) Hence, evaluate 1/26, correct to four decimal places., , 14. Find the root of the equation sin x = 1 + x3, which lies in the interval (– 2, – 1), correct to, three decimal places., 15. Find the approximate root of xex = 3, correct to three decimal places., In the following problems, find the root as specified using the iteration method/method of, successive approximations/fixed point iteration method., 16. Find the smallest positive root of x2 – 5x + 1 = 0, correct to four decimal places., 17. Find the smallest positive root of x5 – 64x + 30 = 0, correct to four decimal places., 18. Find the smallest negative root in magnitude of 3x3 – x + 1 = 0, correct to four decimal, places., 19. Find the smallest positive root of x = e–x, correct to two decimal places., 20. Find the real root of the equation cos x = 3x – 1., 21. The equation, , x2, , (A.U. Nov./Dec. 2006), , + ax + b = 0, has two real roots α and β. Show that the iteration method, , (i) xk+1 = – (axk + b)/xk, is convergent near x = α, if | α | > | β |,, (ii) xk+1 = – b/(xk + a), is convergent near x = α, if | α | < | β |., , 1.2, , LINEAR SYSTEM OF ALGEBRAIC EQUATIONS, , 1.2.1 Introduction, Consider a system of n linear algebraic equations in n unknowns, a11x1 + a12x2 + ... + a1nxn = b1, a21x1 + a22x2 + ... + a2nxn = b2, ..., , ..., , ..., , ..., , an1x1 + an2x2 + ... + annxn = bn, where aij, i = 1, 2, ..., n, j = 1, 2, …, n, are the known coefficients, bi , i = 1, 2, …, n, are the known, right hand side values and xi , i = 1, 2, …, n are the unknowns to be determined., In matrix notation we write the system as, Ax = b, , LMa, a, A= M, MMNa…, , 11, , where, , 21, , n1, , (1.33), , a12, a22, …, an 2, , OP, PP, PQ, , … a1n, … a2n, ,x=, … …, … ann, , LM x OP, LMb OP, x, MM … PP , and b = MMb…PP ., MNx PQ, MNb PQ, 1, , 1, , 2, , 2, , n, , n, , The matrix [A | b], obtained by appending the column b to the matrix A is called the, augmented matrix. That is
Page 37 :
26, , NUMERICAL METHODS, , LMa, a, [A|b] = M, MMNa…, , 11, 21, , n1, , a12, a22, …, an 2, , … a1n, … a2n, … …, … ann, , b1, b2, …, bn, , OP, PP, PQ, , We define the following., (i) The system of equations (1.33) is consistent (has at least one solution), if, rank (A) = rank [A | b] = r., If r = n, then the system has unique solution., If r < n, then the system has (n – r) parameter family of infinite number of solutions., (ii) The system of equations (1.33) is inconsistent (has no solution) if, rank (A) ≠ rank [A | b]., We assume that the given system is consistent., The methods of solution of the linear algebraic system of equations (1.33) may be, classified as direct and iterative methods., (a) Direct methods produce the exact solution after a finite number of steps (disregarding the, round-off errors). In these methods, we can determine the total number of operations (additions, subtractions, divisions and multiplications). This number is called the operational count, of the method., (b) Iterative methods are based on the idea of successive approximations. We start with an, initial approximation to the solution vector x = x0, and obtain a sequence of approximate, vectors x0, x1, ..., xk, ..., which in the limit as k → ∞, converge to the exact solution vector x., Now, we derive some direct methods., 1.2.2 Direct Methods, If the system of equations has some special forms, then the solution is obtained directly., We consider two such special forms., (a) Let A be a diagonal matrix, A = D. That is, we consider the system of equations, Dx = b as, a11x1, , = b1, a22x2, , = b2, ..., , ..., , ..., , an–1, n – 1 xn– 1, , ..., , (1.34), , = bn–1, , annxn = bn, This system is called a diagonal system of equations. Solving directly, we obtain, xi =, , bi, , aii ≠ 0, i = 1, 2, ..., n., aii, , (1.35), , (b) Let A be an upper triangular matrix, A = U. That is, we consider the system of, equations Ux = b as
Page 38 :
27, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , a11x1 + a12x2 + ... ..., , + a1n xn = b1, , a22x2 + ... ..., , + a2n xn = b2, , ..., , ..., , ..., , ..., , (1.36), , an–1, n–1 xn–1 + an–1, n xn = bn–1, annxn = bn, This system is called an upper triangular system of equations. Solving for the unknowns, in the order xn, xn–1, ..., x1, we get, xn = bn/ann,, xn–1 = (bn–1 – an–1, nxn)/an–1, n–1,, ..., , ..., , ..., , F, GGb − ∑ a, H, =, n, , 1, j x j, , 1, , x1, , j=2, , a11, , ..., , I, JJ F, K = GGb − ∑ a, H, n, , 1, , 1, j, , j=2, , xj, , I, JJ, K, , a11, , (1.37), , The unknowns are obtained by back substitution and this procedure is called the back, substitution method., Therefore, when the given system of equations is one of the above two forms, the solution, is obtained directly., Before we derive some direct methods, we define elementary row operations that can be, performed on the rows of a matrix., Elementary row transformations (operations) The following operations on the rows of a, matrix A are called the elementary row transformations (operations)., (i) Interchange of any two rows. If we interchange the ith row with the jth row, then we, usually denote the operation as Ri ↔ Rj., (ii) Division/multiplication of any row by a non-zero number p. If the ith row is multiplied by, p, then we usually denote this operation as pRi., (iii) Adding/subtracting a scalar multiple of any row to any other row. If all the elements of, the jth row are multiplied by a scalar p and added to the corresponding elements of the ith, row, then, we usually denote this operation as Ri ← Ri + pRj. Note the order in which the, operation Ri + pRj is written. The elements of the jth row remain unchanged and the elements, of the ith row get changed., These row operations change the form of A, but do not change the row-rank of A. The, matrix B obtained after the elementary row operations is said to be row equivalent with A. In, the context of the solution of the system of algebraic equations, the solution of the new system, is identical with the solution of the original system., The above elementary operations performed on the columns of A (column C in place of, row R) are called elementary column transformations (operations). However, we shall be using, only the elementary row operations.
Page 39 :
28, , NUMERICAL METHODS, , In this section, we derive two direct methods for the solution of the given system of, equations, namely, Gauss elimination method and Gauss-Jordan method., 1.2.2.1 Gauss Elimination Method, The method is based on the idea of reducing the given system of equations Ax = b, to an, upper triangular system of equations Ux = z, using elementary row operations. We know that, these two systems are equivalent. That is, the solutions of both the systems are identical. This, reduced system Ux = z, is then solved by the back substitution method to obtain the solution, vector x., We illustrate the method using the 3 × 3 system, a11x1 + a12x2 + a13 x3 = b1, a21x1 + a22 x2 + a23 x3 = b2, , (1.38), , a31x1 + a32 x2 + a33 x3 = b3, We write the augmented matrix [A | b] and reduce it to the following form, Gauss elimination, , [A|b] → [U|z], The augmented matrix of the system (1.38) is, , LMa, MNaa, , 11, 21, , 31, , a12, a22, a32, , a13 b1, a 23 b2, a33 b3, , OP, PQ, , (1.39), , First stage of elimination, We assume a11 ≠ 0. This element a11 in the 1 × 1 position is called the first pivot. We use, this pivot to reduce all the elements below this pivot in the first column as zeros. Multiply the, first row in (1.39) by a21/a11 and a31/a11 respectively and subtract from the second and third, rows. That is, we are performing the elementary row operations R2 – (a 21/a11)R1 and, R3 –(a31/a11)R1 respectively. We obtain the new augmented matrix as, , LMa, MM 00, N, , 11, , where, , a12, (1), a22, (1), a32, , a13, (1), a23, (1), a33, , b1, b2(1), b3(1), , FG a, Ha, Fa, – G, Ha, , IJ a, K, IJ a, K, , (1), = a22 –, a22, , (1), = a32, a32, , 21, , 11, , 31, , 11, , OP, PP, Q, , (1.40), , FG a, Ha, Fa, – G, Ha, , 12 ,, , (1), = a23 –, a23, , 12 ,, , (1), = a33, a33, , 21, , 11, , 31, , 11, , IJ a , b, K, IJ a , b, K, 13, , 13, , (1), 2, , (1), 3, , FG a, Ha, Fa, – G, Ha, , = b2 –, , = b3, , IJ b ,, K, IJ b ., K, , 21, , 11, , 31, , 11, , 1, , 1, , Second stage of elimination, (1), (1), We assume a22, ≠ 0 . This element a22, in the 2 × 2 position is called the second pivot., , We use this pivot to reduce the element below this pivot in the second column as zero. Multi-
Page 40 :
29, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , (1), (1), ply the second row in (1.40) by a32, / a22, and subtract from the third row. That is, we are, (1), (1), performing the elementary row operation R3 – ( a32, / a22, )R2. We obtain the new augmented, , matrix as, , LMa, MM 00, N, , 11, , where, , a12, (1), a22, 0, , ( 2), (1), a33, = a33, −, , a13, (1), a23, (2), a33, , Fa I a, GH a JK, (1), 32, (1), 22, , b1, b2(1), b3( 2), , (1), 23 ,, , OP, PP, Q, , b3( 2 ) = b3(1) −, , (1.41), , Fa I b, GH a JK, (1), 32, (1), 22, , (1), 2 ., , ( 2), The element a33, ≠ 0 is called the third pivot. This system is in the required upper, , triangular form [U|z]. The solution vector x is now obtained by back substitution., From the third row, we get, , ( 2), ., x3 = b3( 2) / a33, , From the second row, we get, , (1), (1) ., x2 = (b2(1) − a 23, x 3 )/ a 22, , From the first row, we get, , x1 = (b1 – a12x2 – a13 x3)/a11., , In general, using a pivot, all the elements below that pivot in that column are made zeros., Alternately, at each stage of elimination, we may also make the pivot as 1, by dividing, that particular row by the pivot., Remark 15 When does the Gauss elimination method as described above fail? It fails when, any one of the pivots is zero or it is a very small number, as the elimination progresses. If a, pivot is zero, then division by it gives over flow error, since division by zero is not defined. If a, pivot is a very small number, then division by it introduces large round-off errors and the, solution may contain large errors., For example, we may have the system, 2x2 + 5x3 = 7, 7x1 + x2 – 2x3 = 6, 2x1 + 3x2 + 8x3 = 13, in which the first pivot is zero., Pivoting Procedures How do we avoid computational errors in Gauss elimination? To avoid, computational errors, we follow the procedure of partial pivoting. In the first stage of, elimination, the first column of the augmented matrix is searched for the largest element in, magnitude and brought as the first pivot by interchanging the first row of the augmented, matrix (first equation) with the row (equation) having the largest element in magnitude. In, the second stage of elimination, the second column is searched for the largest element in, magnitude among the n – 1 elements leaving the first element, and this element is brought as, the second pivot by interchanging the second row of the augmented matrix with the later row, having the largest element in magnitude. This procedure is continued until the upper triangular, system is obtained. Therefore, partial pivoting is done after every stage of elimination. There, is another procedure called complete pivoting. In this procedure, we search the entire matrix, A in the augmented matrix for the largest element in magnitude and bring it as the first pivot.
Page 41 :
30, , NUMERICAL METHODS, , This requires not only an interchange of the rows, but also an interchange of the positions of, the variables. It is possible that the position of a variable is changed a number of times during, this pivoting. We need to keep track of the positions of all the variables. Hence, the procedure, is computationally expensive and is not used in any software., Remark 16 Gauss elimination method is a direct method. Therefore, it is possible to count, the total number of operations, that is, additions, subtractions, divisions and multiplications., Without going into details, we mention that the total number of divisions and multiplications, (division and multiplication take the same amount of computer time) is n (n2 + 3n – 1)/3. The, total number of additions and subtractions (addition and subtraction take the same amount of, computer time) is n (n – 1)(2n + 5)/6., Remark 17 When the system of algebraic equations is large, how do we conclude that it is, consistent or not, using the Gauss elimination method? A way of determining the consistency, is from the form of the reduced system (1.41). We know that if the system is inconsistent then, rank (A) ≠ rank [A|b]. By checking the elements of the last rows, conclusion can be drawn, about the consistency or inconsistency., (2), ≠ 0 and b3( 2 ) ≠ 0. Then, rank (A) = rank [A|b] = 3. The, Suppose that in (1.41), a33, , system is consistent and has a unique solution., Suppose that we obtain the reduced system as, , LMa, MM 00, N, , 11, , a12, ( 1), a22, 0, , OP, PP, Q, , a13, (1), a23, 0, , b1, b2( 1) ., b3( 2), , Then, rank (A) = 2, rank [A|b] = 3 and rank (A) ≠ rank [A|b]. Therefore, the system is, inconsistent and has no solution., Suppose that we obtain the reduced system as, , LMa, MMN 00, , 11, , a12, (1), a22, 0, , OP, PPQ, , a13, ( 1), a23, 0, , b1, b2( 1) ., 0, , Then, rank (A) = rank [A|b] = 2 < 3. Therefore, the system has 3 – 2 = 1 parameter, family of infinite number of solutions., Example 1.13 Solve the system of equations, x1 + 10x2 – x3 = 3, 2x1 + 3x2 + 20x3 = 7, 10x1 – x2 + 2x3 = 4, using the Gauss elimination with partial pivoting., Solution We have the augmented matrix as, , LM 1, MN102, , 10 − 1 3, 3 20 7, −1 2 4, , OP, PQ
Page 42 :
31, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , We perform the following elementary row transformations and do the eliminations., R1 ↔ R3 :, , LM10, MN 00, , LM10, MN 21, , −1, 3.2, 101, ., , OP, PQ, , −1, 2 4, 3 20 7 . R2 – (R1/5), R3 – (R1/10) :, 10 − 1 3, 2, 19.6, − 1.2, , R3 – (3.2/10.1)R2 :, , OP, PQ, , LM, MN, , 4, 10, 6.2 . R2 ↔ R3 :, 0, 2.6, 0, , LM10, MN 00, , −1, ., 101, 0, , 2, − 1.2, 19.98020, , −1, 101, ., 3.2, , 2, − 1.2, 19.6, , OP, PQ, , OP, PQ, , 4, 2.6 ., 6.2, , 4, ., 2.6, 5.37624, , Back substitution gives the solution., Third equation gives, , x3 =, , 5.37624, = 0.26908., 19.98020, , Second equation gives, , x2 =, , 1, 1, (2.6 + 1.2x3) =, (2.6 + 1.2(0.26908)) = 0.28940., 10.1, 10.1, , First equation gives, , x1 =, , 1, 1, (4 + x2 – 2x3) =, (4 + 0.2894 – 2(0.26908)) = 0.37512., 10, 10, , Example 1.14 Solve the system of equations, 2x1 + x2 + x3 – 2x4 = – 10, 4x1 + 2x3 + x4 = 8, 3x1 + 2x2 + 2x3 = 7, x1 + 3x2 + 2x3 – x4 = – 5, using the Gauss elimination with partial pivoting., Solution The augmented matrix is given by, , LM2, MM43, N1, , 1, 0, 2, 3, , OP, PP, Q, , 1 − 2 − 10, 2 1, 8, ., 2 0, 7, 2 −1 −5, , We perform the following elementary row transformations and do the eliminations., , R1, , LM4, 2, ↔R : M, MN13, 2, , 0, 1, 2, 3, , OP, PP, Q, , 2 1, 8, 1 − 2 − 10, . R2 – (1/2) R1, R3 – (3/4) R1, R4 – (1/4) R1:, 2 0, 7, 2 −1 − 5
Page 43 :
32, , NUMERICAL METHODS, , LM4, MM00, N0, , OP, PP, Q, , LM4, MM00, N0, , 0 2, 1, 8, 1 0 − 5 / 2 − 14 . R ↔ R :, 2, 4, 2 1/ 2 − 3 / 4 1, 3 3/ 2 − 5 / 4 − 7, , R3 – (2/3) R2, R4 – (1/3)R2:, , LM4, MM00, N0, , LM4, MM00, N0, , OP, PP, Q, , 0 2, 1, 8, 3 3/ 2 − 5/ 4 − 7 ., 2 1/ 2 − 3/ 4, 1, 1 0 − 5/ 2 − 14, , OP, PP, Q, , 0, 2, 1, 8, 3 3/2, − 5/ 4, −7 . R – R :, 4, 3, 0 − 1/ 2 1/ 12, 17 / 3, 0 −1/ 2 − 25 / 12 − 35 / 3, , OP, PP, Q, , 0, 2, 1, 8, − 5/ 4, −7, 3 3/2, ., 0 − 1/ 2 1/ 12, 17 / 3, − 13 / 6 − 52 / 3, 0, 0, , Using back substitution, we obtain, , IJ FG − 6 IJ = 8, x = – 2 FG 17 − 1 x IJ = – 2 FG 17 − 1 ( 8)IJ, H 3 12 K, K H 13 K, H 3 12 K, 1L, F 3I F 5 I O 1 L F 3 I, F 5I O, = M− 7 − G J x + G J x P = M− 7 − G J ( − 10) + G J ( 8)P = 6,, H, K, H, K, H, K, H 4K Q, 3N, 2, 4, Q 3N 2, FG, H, , x4 = −, x2, , 52, 3, , 3, , x1 =, , 3, , 3, , = – 10,, , 4, , 1, 1, [8 – 2x3 – x4] = [8 – 2(– 10) – 8] = 5., 4, 4, , Example 1.15 Solve the system of equations, 3x1 + 3x2 + 4x3 = 20, 2x1 + x2 + 3x3 = 13, x1 + x2 + 3x3 = 6, using the Gauss elimination method., Solution Let us solve this problem by making the pivots as 1. The augmented matrix is given, by, , LM3, MN12, , OP, PQ, , 3 4 20, 1 3 13 ., 1 3 6, , We perform the following elementary row transformations and do the eliminations., , LM, MN, , OP, PQ, , LM, MN, , OP, PQ, , 1 1 4 / 3 20/ 3, 1 1 4 / 3 20/ 3, R1/3: 2 1 3, 13 . R2 – 2R1, R3 – R1: 0 − 1 1/ 3 − 1/ 3 ., 1 1 3, 6, 0 0 5/ 3 − 2/3
Page 44 :
33, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , Back substitution gives the solution as, x3 = –, x1 =, , FG 2 IJ FG 3IJ = – 2 , x, H 3 K H 5K 5, , 2, , =, , FG IJ, H K, , 1 x3 1 1, 2, 1, +, = +, −, = ,, 3, 3, 3 3, 5, 5, , FG IJ, H K, , 20 1 4, 2, 35, 20, 4, =, − −, −, – x2 – x3 =, = 7., 3, 5 3, 5, 5, 3, 3, , Example 1.16 Test the consistency of the following system of equations, x1 + 10x2 – x3 = 3, 2x1 + 3x2 + 20x3 = 7, 9x1 + 22x2 + 79x3 = 45, using the Gauss elimination method., Solution We have the augmented matrix as, , LM 1, MN29, , OP, PQ, , 10 − 1 3, 3 20 7 ., 22 79 45, , We perform the following elementary row transformations and do the eliminations., , LM, MN, , OP, PQ, , LM, MN, , OP, PQ, , 1 10 − 1 3, 1 10 − 1 3, R2 – 2R1, R3 – 9R1 : 0 − 17 22 1 . R3 – 4R2 : 0 − 17 22 1 ., 0 − 68 88 18, 0, 0, 0 14, Now, rank [A] = 2, and rank [A|b] = 3. Therefore, the system is inconsistent and has no, solution., 1.2.2.2 Gauss-Jordan Method, The method is based on the idea of reducing the given system of equations Ax = b, to a, diagonal system of equations Ix = d, where I is the identity matrix, using elementary row, operations. We know that the solutions of both the systems are identical. This reduced system, gives the solution vector x. This reduction is equivalent to finding the solution as x = A–1b., Gauss - Jordan method, , [A|b] → [I | X], In this case, after the eliminations are completed, we obtain the augmented matrix for, a 3 × 3 system as, , and the solution is, , LM1, MN00, , 0, 1, 0, , 0, 0, 1, , d1, d2, d3, , OP, PQ, , xi = di, i = 1, 2, 3., , (1.42)
Page 45 :
34, , NUMERICAL METHODS, , Elimination procedure The first step is same as in Gauss elimination method, that is, we, make the elements below the first pivot as zeros, using the elementary row transformations., From the second step onwards, we make the elements below and above the pivots as zeros, using the elementary row transformations. Lastly, we divide each row by its pivot so that the, final augmented matrix is of the form (1.42). Partial pivoting can also be used in the solution., We may also make the pivots as 1 before performing the elimination., Let us illustrate the method., Example 1.17 Solve the following system of equations, x1 + x2 + x3 = 1, 4x1 + 3x2 – x3 = 6, 3x1 + 5x2 + 3x3 = 4, using the Gauss-Jordan method (i) without partial pivoting, (ii) with partial pivoting., Solution We have the augmented matrix as, , LM1, MN43, , OP, PQ, , 1, 1 1, 3 −1 6, 5, 3 4, , (i) We perform the following elementary row transformations and do the eliminations., R2 – 4R1, R3 – 3R1 :, , LM, MN, , LM 1, MN00, , 1, R1 + R2, R3 + 2R2 : 0, 0, , 1, −1, 2, 0, −1, 0, , 1, −5, 0, −4, −5, − 10, , LM, MN, , 1, R1 – (4/10)R3, R2 – (5/10) R3 : 0, 0, , OP, PQ, 3O, 2P ., P, 5Q, , 1, 2 ., 1, , 0, −1, 0, , 0, 0, − 10, , OP, PQ, , 1, − 1/2 ., 5, , Now, making the pivots as 1, ((– R2), (R3/(– 10))) we get, , LM1, MN00, , 0, 1, 0, , 0, 0, 1, , OP, PQ, , 1, 1/2 ., − 1/2, , Therefore, the solution of the system is x1 = 1, x2 = 1/2, x3 = – 1/2., (ii) We perform the following elementary row transformations and do the elimination., , LM, MN, , 4, R1 ↔ R 2 : 1, 3, , 3, 1, 5, , −1, 1, 3, , OP, PQ, , 6, 1 ., 4, , LM, MN, , OP, PQ, , 1 3/4 − 1/4 3/2, R1/4 : 1 1, 1, 1 ., 3 5, 3, 4
Page 46 :
35, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , LM1, MN00, , R2 – R1, R3 – 3R1 :, , R2 ↔ R3, , LM1, : 0, MN0, , 3/4, 11/4, 1/4, , 3/4, 1/4, 11/4, , − 1/4, 15/4, 5/4, , R1 – (3/4) R2, R3 – (1/4)R2 :, , R3 /(10/11) :, , LM1, MN00, , 0, 1, 0, , OP, PQ, , − 1/4, 5/4, 15/4, , 3/2, − 1/2 ., − 1/2, , OP, PQ, , LM, MN, , 3/2, 1, − 1/2 . R2 /(11/4) : 0, 0, − 1/2, , LM 1, MN00, , − 14/11, 15/11, 1, , 3/4, 1, 1/4, , − 1/4, 15/11, 5/4, , OP, PQ, , OP, PQ, , 3/2, − 2/11 ., − 1/2, , 0 − 14/11 18/11, 1 15/11 − 2/11 ., 0, 10/11 − 5/11, , OP, PQ, , 18/11, − 2/11 ., − 1/2, , LM, MN, , 1, R1 + (14/11) R3, R2 – (15/11)R3 : 0, 0, , 0, 1, 0, , 0, 0, 1, , OP, PQ, , 1, 1/2 ., − 1/2, , Therefore, the solution of the system is x1 = 1, x2 = 1/2, x3 = – 1/2., Remark 18 The Gauss-Jordan method looks very elegant as the solution is obtained directly., However, it is computationally more expensive than Gauss elimination. For large n, the total, number of divisions and multiplications for Gauss-Jordan method is almost 1.5 times the, total number of divisions and multiplications required for Gauss elimination. Hence, we do, not normally use this method for the solution of the system of equations. The most important, application of this method is to find the inverse of a non-singular matrix. We present this, method in the following section., 1.2.2.3 Inverse of a Matrix by Gauss-Jordan Method, As given in Remark 18, the important application of the Gauss-Jordan method is to, find the inverse of a non-singular matrix A. We start with the augmented matrix of A with the, identity matrix I of the same order. When the Gauss-Jordan procedure is completed, we obtain, Gauss - Jordan method, , [A | I] → [I | A–1], since, AA–1 = I., Remark 19 Partial pivoting can also be done using the augmented matrix [A|I]. However,, we cannot first interchange the rows of A and then find the inverse. Then, we would be finding, the inverse of a different matrix., Example 1.18 Find the inverse of the matrix, , LM 1, MN43, , OP, PQ, , 1, 1, 3 −1, 5, 3
Page 47 :
36, , NUMERICAL METHODS, , using the Gauss-Jordan method (i) without partial pivoting, and (ii) with partial pivoting., Solution Consider the augmented matrix, , LM1, MN43, , 1, 3, 5, , 1, −1, 3, , 1, 0, 0, , OP, PQ, , 0, 1, 0, , 0, 0 ., 1, , (i) We perform the following elementary row transformations and do the eliminations., R2 – 4R1, R3 – 3R1:, , LM, MN, , 1, – R2 : 0, 0, , 1, 1, 2, , 1, 5, 0, , 1, 4, −3, , R1 – R2, R3 – 2R2 :, , LM1, R /(– 10) : 0, MN0, 3, , LM1, MN00, , 0, 1, 0, , R1 + 4R3, R2 – 5R3, , LM1, MN00, , OP, PQ, , 0, −1, 0, , 0, 0, 1, , OP, PQ, , −4 −3, 0, 1 0, 1, 5, 4 −1 0 ., 0 − 10 − 11 2 1, , −4, 5, 1, , LM1, : 0, MN0, , OP, PQ, , 1, 1, 1 0 0, −1 −5 − 4 1 0 ., 2, 0 −3 0 1, , −3, 4, 11/10, 0, 1, 0, , 0, 0, 1, , OP, PQ, , 1, −1, − 2/10, , 0, ., 0, − 1/10, , 14/10, − 15/10, 11/10, , 2/10, 0, − 2/10, , OP, PQ, , − 4/10, 5/10 ., − 1/10, , Therefore, the inverse of the given matrix is given by, , LM 7/5, MN11− 3/10/2, , 1/5, 0, − 1/5, , OP, PQ, , − 2/5, 1/2 ., − 1/10, , (ii) We perform the following elementary row transformations and do the eliminations., R1, , R2, , R2, , LM4, : 1, MN3, , OP, PQ, , LM1, ↔R, R /4 : 1, MN3, L1 3/4 − 1/4 0 1/4 0O, – R , R – 3R : M0 1/4 5/4 1 − 1/4 0P ., MN0 11/4 15/4 0 − 3/4 1PQ, L1 3/4 − 1/4 0 1/4 0O, ↔ R : M0 11/4 15/4 0 − 3/4 1 P ., MN0 1/4 5/4 1 − 1/4 0PQ, 2, , 1, , 3, , 3, , 3, 1, 5, , 1, , −1, 1, 3, , 0, 1, 0, , 1, 0, 0, , 0, 0 ., 1, , 1, , 3/4, 1, 5, , − 1/4, 1, 3, , 0, 1, 0, , 1/4, 0, 0, , OP, PQ, , 0, 0 ., 1
Page 48 :
37, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , LM, MN, , 1, R2 /(11/4) : 0, 0, , 3/4, 1, 1/4, , − 1/4, /, 1511, 5/4, , LM, MN, , 1, R1 – (3/4) R2, R3 – (1/4)R2 : 0, 0, , LM, MN, , 1, R3 /(10/11) : 0, 0, , 0, 1, 0, , OP, PQ, , 1/4, − 311, /, − 1/4, , 0, 0, 1, 0, 1, 0, , 0, / ., 411, 0, , − 1411, /, 1511, /, 1011, /, , − 14/11, 0, 1511, /, 0, 1, 1110, /, , 0, 0, 1, , LM, MN, , 0, 1, 0, , OP, PQ, , − 311, /, 4/11 ., − 111, /, , OP, PQ, , 511, /, − 311, /, − 15, /, , 1, R 1 + (14/11) R3, R2 – (15/11)R3 : 0, 0, , 511, /, − 311, /, − 211, /, , − 311, /, 411, /, ., − 110, /, , 0, 0, 1, , 7/5, − 3/2, 1110, /, , 1/5, 0, − 1/5, , OP, PQ, , − 2/5, 1/2 ., − 110, /, , Therefore, the inverse of the matrix is given by, , LM 7/5, 3/2, MN− 1110, /, , OP, PQ, , /, 15, 0, − 15, /, , − 2/5, 1/2, − 110, /, , Example 1.19 Using the Gauss-Jordan method, find the inverse of, , LM2, MN21, , OP, PQ, , 2 3, 1 1 ., 3 5, , (A.U. Apr./May 2004), , Solution We have the following augmented matrix., , LM2, MN21, , 2, 1, 3, , 3, 1, 5, , 1, 0, 0, , 0, 1, 0, , OP, PQ, , 0, 0 ., 1, , We perform the following elementary row transformations and do the eliminations., , LM, MN, , LM, MN, , OP, PQ, , 1 1 3/2 1/2 0 0, 1, R1 / 2 : 2 1 1, 0 1 0 . R2 – 2R1, R3 – R1 : 0, 0, 1 3 5, 0 0 1, , LM, MN, , 1, R2 ↔ R3. Then, R2/2 : 0, 0, , LM, MN, , 1, R1 – R2, R3 + R2 : 0, 0, , 0, 1, 0, , 1, 1, −1, − 1/4, 7/4, − 1/4, , 3/2, 7/4, −2, 3/4, − 1/4, − 5/4, , 1/2, − 1/4, −1, 0, 0, 1, , 1, −1, 2, , OP, PQ, , 0 0, 0 1/2 ., 1 0, , OP, PQ, , − 1/2, 1/2 ., 1/2, , 3/2, −2, 7/2, , 1/2, −1, − 1/2, , 0, 1, 0, , OP, PQ, , 0, 0 ., 1
Page 49 :
38, , NUMERICAL METHODS, , R3 /(– 1/4) :, , LM1, MN00, , 0, 1, 0, , − 1/4, 7/4, 1, , 3/4, − 1/4, 5, , LM, MN, , 1, R1 + (1/4)R3, R2 – (7/4)R3 : 0, 0, , 0, 0, −4, 0, 1, 0, , 0, 0, 1, , OP, PQ, , − 1/2, 1/2 ., −2, 2, −9, 5, , −1, 7, −4, , Therefore, the inverse of the given matrix is given by, , LM 2, MN− 95, , −1, 7, −4, , OP, PQ, , −1, 4 ., −2, , OP, PQ, , −1, 4 ., −2, , REVIEW QUESTIONS, 1. What is a direct method for solving a linear system of algebraic equations Ax = b ?, Solution Direct methods produce the solutions in a finite number of steps. The number, of operations, called the operational count, can be calculated., 2. What is an augmented matrix of the system of algebraic equations Ax = b ?, Solution The augmented matrix is denoted by [A | b], where A and b are the coefficient matrix and right hand side vector respectively. If A is an n × n matrix and b is an, n × 1 vector, then the augmented matrix is of order n × (n + 1)., 3. Define the rank of a matrix., Solution The number of linearly independent rows/columns of a matrix define the rowrank/column-rank of that matrix. We note that row-rank = column-rank = rank., 4. Define consistency and inconsistency of a system of linear system of algebraic equations Ax = b., Solution Let the augmented matrix of the system be [A | b]., (i) The system of equations Ax = b is consistent (has at least one solution), if, rank (A) = rank [A | b] = r., If r = n, then the system has unique solution., If r < n, then the system has (n – r) parameter family of infinite number of solutions., (ii) The system of equations Ax = b is inconsistent (has no solution) if, rank (A) ≠ rank [A | b]., 5. Define elementary row transformations., Solution We define the following operations as elementary row transformations., (i) Interchange of any two rows. If we interchange the ith row with the jth row, then we, usually denote the operation as Ri ↔ Rj., (ii) Division/multiplication of any row by a non-zero number p. If the ith row is multiplied by p, then we usually denote this operation as pRi.
Page 50 :
SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , 39, , (iii) Adding/subtracting a scalar multiple of any row to any other row. If all the elements, of the jth row are multiplied by a scalar p and added to the corresponding elements, of the ith row, then, we usually denote this operation as Ri ← Ri + pRj. Note the, order in which the operation Ri + pRj is written. The elements of the jth row remain, unchanged and the elements of the ith row get changed., 6. Which direct methods do we use for (i) solving the system of equations Ax = b, and (ii), finding the inverse of a square matrix A?, Solution (i) Gauss elimination method and Gauss-Jordan method. (ii) Gauss-Jordan, method., 7. Describe the principle involved in the Gauss elimination method., Solution The method is based on the idea of reducing the given system of equations Ax, = b, to an upper triangular system of equations Ux = z, using elementary row operations. We know that these two systems are equivalent. That is, the solutions of both the, systems are identical. This reduced system Ux = z, is then solved by the back substitution method to obtain the solution vector x., 8. When does the Gauss elimination method fail?, Solution Gauss elimination method fails when any one of the pivots is zero or it is a, very small number, as the elimination progresses. If a pivot is zero, then division by it, gives over flow error, since division by zero is not defined. If a pivot is a very small, number, then division by it introduces large round off errors and the solution may contain large errors., 9. How do we avoid computational errors in Gauss elimination?, Solution To avoid computational errors, we follow the procedure of partial pivoting. In, the first stage of elimination, the first column of the augmented matrix is searched for, the largest element in magnitude and brought as the first pivot by interchanging the, first row of the augmented matrix (first equation) with the row (equation) having the, largest element in magnitude. In the second stage of elimination, the second column is, searched for the largest element in magnitude among the n – 1 elements leaving the, first element, and this element is brought as the second pivot by interchanging the, second row of the augmented matrix with the later row having the largest element in, magnitude. This procedure is continued until the upper triangular system is obtained., Therefore, partial pivoting is done after every stage of elimination., 10. Define complete pivoting in Gauss elimination., Solution In this procedure, we search the entire matrix A in the augmented matrix for, the largest element in magnitude and bring it as the first pivot. This requires not only, an interchange of the equations, but also an interchange of the positions of the variables. It is possible that the position of a variable is changed a number of times during, this pivoting. We need to keep track of the positions of all the variables. Hence, the, procedure is computationally expensive and is not used in any software., 11. Describe the principle involved in the Gauss-Jordan method for finding the inverse of a, square matrix A.
Page 52 :
41, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , Show that the following systems of equations are inconsistent using the Gauss elimination, method., 13. 2x1 + x2 – 3x3 = 0, , 14. x1 – 3x2 + 4x3 = 2, , 5x1 + 8x2 + x3 = 14,, , x1 + x2 – x3 = 0, , 4x1 + 13x2 + 11x3 = 25., , 3x1 – x2 + 2x3 = 4., , Show that the following systems of equations have infinite number of solutions using the Gauss, elimination., 15. 2x1 + x2 – 3x3 = 0,, , 16. x1 + 5x2 – x3 = 0,, , 5x1 + 8x2 + x3 = 14,, , 2x1 + 3x2 + x3 = 11,, , 4x1 + 13x2 + 11x3 = 28., , 5x1 + 11x2 + x3 = 22., , 1.2.3 Iterative Methods, As discussed earlier, iterative methods are based on the idea of successive approximations., We start with an initial approximation to the solution vector x = x0, to solve the system of, equations Ax = b, and obtain a sequence of approximate vectors x0, x1, ..., xk, ..., which in the, limit as k → ∞, converges to the exact solution vector x = A–1b. A general linear iterative, method for the solution of the system of equations Ax = b, can be written in matrix form as, x(k+1) = Hx(k) + c, k = 0, 1, 2, …, , (1.43), , where x(k+1) and x(k) are the approximations for x at the (k + 1)th and kth iterations respectively. H is called the iteration matrix, which depends on A and c is a column vector, which, depends on A and b., When to stop the iteration We stop the iteration procedure when the magnitudes of the, differences between the two successive iterates of all the variables are smaller than a given, accuracy or error tolerance or an error bound ε, that is,, xi( k + 1) − xi( k) ≤ ε, for all i., , (1.44), , For example, if we require two decimal places of accuracy, then we iterate until, xi( k + 1) − xi( k) < 0.005, for all i. If we require three decimal places of accuracy, then we iterate, ( + 1), − xi( k) < 0.0005, for all i., until xi k, , Convergence property of an iterative method depends on the iteration matrix H., Now, we derive two iterative methods for the solution of the system of algebraic equations, a11x1 + a12x2 + a13x3 = b1, a21x1 + a22x2 + a23x3 = b2, , (1.45), , a31x1 + a32x2 + a33x3 = b3, 1.2.3.1 Gauss-Jacobi Iteration Method, Sometimes, the method is called Jacobi method. We assume that the pivots aii ≠ 0, for, all i. Write the equations as
Page 53 :
42, , NUMERICAL METHODS, , a11x1 = b1 – (a12x2 + a13x3), a22x2 = b2 – (a21x1 + a23x3), a33x3 = b3 – (a31x1 + a32x2), The Jacobi iteration method is defined as, x1( k + 1) =, , 1, [b1 − ( a12 x2( k) + a13 x3( k) )], a11, , x2( k + 1) =, , 1, [b2 − (a21 x1( k) + a23 x3( k) )], a22, , x3( k + 1) =, , 1, [b3 − ( a31 x1( k) + a32 x2( k) )] ,, a33, , k = 0, 1, 2, ..., , (1.46), , Since, we replace the complete vector x(k) in the right hand side of (1.46) at the end of, each iteration, this method is also called the method of simultaneous displacement., Remark 20 A sufficient condition for convergence of the Jacobi method is that the system of, equations is diagonally dominant, that is, the coefficient matrix A is diagonally dominant. We, n, , can verify that | aii | ≥, , ∑ |a, , ij |., , This implies that convergence may be obtained even if the, , j =1, i ≠ j, , system is not diagonally dominant. If the system is not diagonally dominant, we may exchange, the equations, if possible, such that the new system is diagonally dominant and convergence, is guaranteed. However, such manual verification or exchange of equations may not be possible, for large systems that we obtain in application problems. The necessary and sufficient condition, for convergence is that the spectral radius of the iteration matrix H is less than one unit, that, is, ρ(H) < 1, where ρ(H) is the largest eigen value in magnitude of H. Testing of this condition, is beyond the scope of the syllabus., Remark 21 How do we find the initial approximations to start the iteration? If the system is, diagonally dominant, then the iteration converges for any initial solution vector. If no suitable, approximation is available, we can choose x = 0, that is xi = 0 for all i. Then, the initial, approximation becomes xi = bi /aii, for all i., Example 1.20 Solve the system of equations, 4x1 + x2 + x3 = 2, x1 + 5x2 + 2x3 = – 6, x1 + 2x2 + 3x3 = – 4, using the Jacobi iteration method. Use the initial approximations as, (i) xi = 0, i = 1, 2, 3,, , (ii) x1 = 0.5, x2 = – 0.5, x3 = – 0.5., , Perform five iterations in each case., Solution Note that the given system is diagonally dominant. Jacobi method gives the iterations, as, x1(k+1) = 0.25 [2 – (x2(k) + x3(k))]
Page 54 :
43, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , x2(k+1) = 0.2 [– 6 – (x1(k) + 2x3(k))], x3(k+1) = 0.33333 [– 4 – (x1(k) + 2x2(k))],, , k = 0, 1, ..., , We have the following results., (i) x1(0) = 0, x2(0) = 0, x3(0) = 0., First iteration, x1(1) = 0.25 [2 – (x2(0) + x3(0))] = 0.5,, x2(1) = 0.2 [– 6 – (x1(0) + 2x3(0))] = – 1.2,, x3(1) = 0.33333 [– 4 – (x1(0) + 2x2(0))] = – 1.33333., Second iteration, x1(2) = 0.25 [2 – (x2(1) + x3(1))] = 0.25 [2 – (– 1.2 – 1.33333)] = 1.13333,, x2(2) = 0.2 [– 6 – (x1(1) + 2x3(1))] = 0.2 [– 6 – (0.5 + 2(– 1.33333))] = – 0.76668,, x3(2) = 0.33333 [– 4 – (x1(1) + 2x2(1))] = 0.33333 [– 4 – (0.5 + 2(– 1.2))] = – 0.7., Third iteration, x1(3) = 0.25 [2 – (x2(2) + x3(2))] = 0.25 [2 – (– 0.76668 – 0.7)] = 0.86667,, x2(3) = 0.2 [– 6 – (x1(2) + 2x3(2))] = 0.2 [– 6 – (1.13333 + 2(– 0.7))] = – 1.14667,, x3(3) = 0.33333 [– 4 – (x1(2) + 2x2(2))], = 0.33333 [– 4 – (1.13333 + 2(– 0.76668))] = – 1.19998., Fourth iteration, x1(4) = 0.25 [2 – (x2(3) + x3(3))] = 0.25 [2 – (– 1.14667 – 1.19999)] = 1.08666,, x2(4) = 0.2 [– 6 – (x1(3) + 2x3(3))] = 0.2 [– 6 – (0.86667 + 2(– 1.19998))] = – 0.89334,, x3(4) = 0.33333 [– 4 – (x1(3) + 2x2(3))], = 0.33333 [– 4 – (0.86667 + 2(– 1.14667))] = – 0.85777., Fifth iteration, x1(5) = 0.25 [2 – (x2(4) + x3(4))] = 0.25 [2 – (– 0.89334 – 0.85777)] = 0.93778,, x2(5) = 0.2 [– 6 – (x1(4) + 2x3(4))] = 0.2 [– 6 – (1.08666 + 2(– 0.85777))] = – 1.07422,, x3(5) = 0.33333 [– 4 – (x1(4) + 2x2(4))], = 0.33333 [– 4 – (1.08666 + 2(– 0.89334))] = – 1.09998., It is interesting to note that the iterations oscillate and converge to the exact solution, x1 = 1.0, x2 = – 1, x3 = – 1.0., (ii) x1(0) = 0.5, x2(0) = – 0.5, x3(0) = – 0.5., First iteration, x1(1) = 0.25 [2 – (x2(0) + x3(0))] = 0.25 [2 – (– 0.5 – 0.5)] = 0.75,, x2(1) = 0.2 [– 6 – (x1(0) + 2x3(0))] = 0.2 [– 6 – (0.5 + 2(– 0.5))] = – 1.1,, x3(1) = 0.33333 [– 4 – (x1(0) + 2x2(0))] = 0.33333 [– 4 – (0.5 + 2(– 0.5))] = – 1.16667.
Page 55 :
44, , NUMERICAL METHODS, , Second iteration, x1(2) = 0.25 [2 – (x2(1) + x3(1))] = 0.25 [2 – (– 1.1 – 1.16667)] = 1.06667,, x2(2) = 0.2 [– 6 – (x1(1) + 2x3(1))] = 0.2 [– 6 – (0.75 + 2(– 1.16667))] = – 0.88333,, x3(2) = 0.33333 [– 4 – (x1(1) + 2x2(1))] = 0.33333 [– 4 – (0.75 + 2(– 1.1))] = – 0.84999., Third iteration, x1(3) = 0.25 [2 – (x2(2) + x3(2))] = 0.25 [2 – (– 0.88333 – 0.84999)] = 0.93333,, x2(3) = 0.2 [– 6 – (x1(2) + 2x3(2))] = 0.2 [– 6 – (1.06667 + 2(– 0.84999))] = – 1.07334,, x3(3) = 0.33333 [– 4 – (x1(2) + 2x2(2))], = 0.33333 [– 4 – (1.06667 + 2(– 0.88333))] = – 1.09999., Fourth iteration, x1(4) = 0.25 [2 – (x2(3) + x3(3))] = 0.25 [2 – (– 1.07334 – 1.09999)] = 1.04333,, x2(4) = 0.2 [– 6 – (x1(3) + 2x3(3))] = 0.2 [– 6 – (0.93333 + 2(– 1.09999))] = – 0.94667,, x3(4) = 0.33333 [– 4 – (x1(3) + 2x2(3))], = 0.33333 [– 4 – (0.93333 + 2(– 1.07334))] = – 0.92887., Fifth iteration, x1(5) = 0.25 [2 – (x2(4) + x3(4))] = 0.25 [2 – (– 0.94667 – 0.92887)] = 0.96889,, x2(5) = 0.2 [– 6 – (x1(4) + 2x3(4))] = 0.2 [– 6 – (1.04333 + 2(– 0.92887))] = – 1.03712,, x3(5) = 0.33333 [– 4 – (x1(4) + 2x2(4))], = 0.33333 [– 4 – (1.04333 + 2(– 0.94667))] = – 1.04999., Example 1.21 Solve the system of equations, 26x1 + 2x2 + 2x3 = 12.6, 3x1 + 27x2 + x3 = – 14.3, 2x1 + 3x2 + 17x3 = 6.0, using the Jacobi iteration method. Obtain the result correct to three decimal places., Solution The given system of equations is strongly diagonally dominant. Hence, we can expect faster convergence. Jacobi method gives the iterations as, x1(k+1) = [12.6 – (2x2(k) + 2x3(k))]/26, x2(k+1) = [– 14.3 – (3x1(k) + x3(k))]/27, x3(k+1) = [6.0 – (2x1(k) + 3x2(k))]/17, Choose the initial approximation as, results., , x1(0), , k = 0, 1, ..., = 0, x2(0) = 0, x3(0) = 0. We obtain the following, , First iteration, x1(1) =, , 1, 1, [12.6 – (2x2(0) + 2x3(0))] =, [12.6] = 0.48462,, 26, 26
Page 56 :
SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , x2(1) =, , 1, 1, [– 14.3 – (3x1(0) + x3(0))] =, [– 14.3] = – 0.52963,, 27, 27, , x3(1) =, , 1, 1, [6.0 – (2x1(0) + 3x2(0))] =, [6.0] = 0.35294., 17, 17, , 45, , Second iteration, x1(2) =, , 1, 1, [12.6 – (2x2(1) + 2x3(1))] =, [12.6 – 2 (– 0.52963 + 0.35294)] = 0.49821,, 26, 26, , x2(2) =, , 1, 1, [– 14.3 – (3x1(1) + x3(1))] =, [– 14.3 – (3(0.48462) + 0.35294)] = – 0.59655,, 27, 27, , x3(2) =, , 1, 1, [– 6.0 – (2x1(1) + 3x2(1))] =, [6.0 – (2(0.48462) + 3(– 0.52963))] = 0.38939., 17, 17, , Third iteration, x1(3) =, , 1, 1, [12.6 – (2x2(2) + 2x3(2))] =, [12.6 – 2(– 0.59655 + 0.38939)] = 0.50006,, 26, 26, , x2(3) =, , 1, 1, [– 14.3 – (3x1(2) + x3(2))] =, [– 14.3 – (3(0.49821) + 0.38939)] = – 0.59941,, 27, 27, , x3(3) =, , 1, 1, [– 6.0 – (2x1(2) + 3x2(2))] =, [6.0 – (2(0.49821) + 3(– 0.59655))] = 0.39960., 17, 17, , Fourth iteration, x1(4) =, , 1, 1, [12.6 – (2x2(3) + 2x3(3))] =, [12.6 – 2(– 0.59941 + 0.39960)] = 0.50000,, 26, 26, , x2(4) =, , 1, 1, [– 14.3 – (3x1(3) + x3(3))] =, [– 14.3 – (3(0.50006) + 0.39960)] = – 0.59999,, 27, 27, , x3(4) =, , 1, 1, [– 6.0 – (2x1(3) + 3x2(3))] =, [6.0 – (2(0.50006) + 3(– 0.59941))] = 0.39989., 17, 17, , We find, , x1( 4 ) − x1( 3 ) = | 0.5 – 0.50006 | = 0.00006,, x 2( 4 ) − x 2( 3 ) = | – 0.59999 + 0.59941 | = 0.00058,, x 3( 4 ) − x 3( 3 ) = | 0.39989 – 0.39960 | = 0.00029., , Three decimal places of accuracy have not been obtained at this iteration., Fifth iteration, x1(5) =, , 1, 1, [12.6 – (2x2(4) + 2x3(4))] =, [12.6 – 2(– 0.59999 + 0.39989)] = 0.50001,, 26, 26, , x2(5) =, , 1, 1, [– 14.3 – (3x1(4) + x3(4))] =, [– 14.3 – (3(0.50000) + 0.39989)] = – 0.60000,, 27, 27
Page 57 :
46, , NUMERICAL METHODS, , x3(5) =, , 1, 1, [– 6.0 – (2x1(4) + 3x2(4))] =, [6.0 – (2(0.50000) + 3(– 0.59999))] = 0.40000., 17, 17, , (4), (3 ), We find x1 − x1, = | 0.50001 – 0.5 | = 0.00001,, , x 2( 4 ) − x 2( 3 ) = | – 0.6 + 0.59999 | = 0.00001,, x 3( 4 ) − x 3( 3 ) = | 0.4 – 0.39989 | = 0.00011., , Since, all the errors in magnitude are less than 0.0005, the required solution is, x1 = 0.5, x2 = – 0.6, x3 = 0.4., Remark 22 What is the disadvantage of the Gauss-Jacobi method? At any iteration step, the, value of the first variable x1 is obtained using the values of the previous iteration. The value of, the second variable x2 is also obtained using the values of the previous iteration, even though, the updated value of x1 is available. In general, at every stage in the iteration, values of the, previous iteration are used even though the updated values of the previous variables are, available. If we use the updated values of x1, x2,..., xi–1 in computing the value of the variable, xi, then we obtain a new method called Gauss-Seidel iteration method., 1.2.3.2 Gauss-Seidel Iteration Method, As pointed out in Remark 22, we use the updated values of x1, x2,..., xi–1 in computing, the value of the variable xi. We assume that the pivots aii ≠ 0, for all i. We write the equations, as, a11x1 = b1 – (a12x2 + a13x3), a22x2 = b2 – (a21x1 + a23x3), a33x3 = b3 – (a31x1 + a32x2), The Gauss-Seidel iteration method is defined as, x1(k+1) =, , 1, [b – (a12x2(k) + a13x3(k))], a11 1, , x2(k+1) =, , 1, [b – (a21x1(k+1) + a23x3(k))], a 22 2, , x3(k+1) =, , 1, [b – (a31x1(k+1) + a32x2(k+1))], a33 3, , (1.47), , k = 0, 1, 2,..., This method is also called the method of successive displacement., We observe that (1.47) is same as writing the given system as, a11x1(k+1), , = b1 – (a12 x2(k) + a13 x3(k)), , a21x1(k+1) + a22 x2(k+1), , = b2 – a23 x3(k), , a31x1(k+1), , + a32 x2, , (k+1), , +, , a33x3(k+1), , = b3, , (1.48)
Page 58 :
SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , 47, , Remark 23 A sufficient condition for convergence of the Gauss-Seidel method is that the system of equations is diagonally dominant, that is, the coefficient matrix A is diagonally dominant. This implies that convergence may be obtained even if the system is not diagonally, dominant. If the system is not diagonally dominant, we may exchange the equations, if possible, such that the new system is diagonally dominant and convergence is guaranteed. The, necessary and sufficient condition for convergence is that the spectral radius of the iteration, matrix H is less than one unit, that is, ρ(H) < 1, where ρ(H) is the largest eigen value in, magnitude of H. Testing of this condition is beyond the scope of the syllabus., If both the Gauss-Jacobi and Gauss-Seidel methods converge, then Gauss-Seidel method, converges at least two times faster than the Gauss-Jacobi method., Example 1.22 Find the solution of the system of equations, 45x1 + 2x2 + 3x3 = 58, – 3x1 + 22x2 + 2x3 = 47, 5x1 + x2 + 20x3 = 67, correct to three decimal places, using the Gauss-Seidel iteration method., Solution The given system of equations is strongly diagonally dominant. Hence, we can expect, fast convergence. Gauss-Seidel method gives the iteration, x1(k+1) =, , 1, (58 – 2x2(k) – 3x3(k)),, 45, , x2(k+1) =, , 1, (47 + 3x1(k+1) – 2x3(k)),, 22, , x3(k+1) =, , 1, (67 – 5x1(k+1) – x2(k+1))., 20, , Starting with x1(0) = 0, x2(0) = 0, x3(0) = 0, we get the following results., First iteration, x1(1) =, , 1, 1, (58 – 2x2(0) – 3x3(0)) =, (58) = 1.28889,, 45, 45, , x2(1) =, , 1, 1, (47 + 3x1(1) – 2x3(0)) =, (47 + 3(1.28889) – 2(0)) = 2.31212,, 22, 22, , x3(1) =, , 1, 1, (67 – 5x1(1) – x2(1)) =, (67 – 5(1.28889) – (2.31212)) = 2.91217., 20, 20, , Second iteration, x1(2) =, , 1, 1, (58 – 2x2(1) – 3x3(1)) =, (58 – 2(2.31212) – 3(2.91217)) = 0.99198,, 45, 45, , x2(2) =, , 1, 1, (47 + 3x1(2) – 2x3(1)) =, (47 + 3(0.99198) – 2(2.91217)) = 2.00689,, 22, 22
Page 59 :
48, , NUMERICAL METHODS, , x3(2) =, , 1, 1, (67 – 5x1(2) – x2(2)) =, (67 – 5(0.99198) – (2.00689)) = 3.00166., 20, 20, , Third iteration, x1(3) =, , 1, 1, (58 – 2x2(2) – 3x3(2)) =, (58 – 2(2.00689) – 3(3.00166) = 0.99958,, 45, 45, , x2(3) =, , 1, 1, (47 + 3x1(3) – 2x3(2)) =, (47 + 3(0.99958) – 2(3.00166)) = 1.99979,, 22, 22, , x3(3) =, , 1, 1, (67 – 5x1(3) – x2(3)) =, (67 – 5(0.99958) – (1.99979)) = 3.00012., 20, 20, , Fourth iteration, x1(4) =, , 1, 1, (58 – 2x2(3) – 3x3(3)) =, (58 – 2(1.99979) – 3(3.00012)) = 1.00000,, 45, 45, , x2(4) =, , 1, 1, (47 + 3x1(4) – 2x3(3)) =, (47 + 3(1.00000) – 2(3.00012)) = 1.99999,, 22, 22, , x3(4) =, , 1, 1, (67 – 5x1(4) – x2(4)) =, (67 – 5(1.00000) – (1.99999)) = 3.00000., 20, 20, , We find, , x1( 4 ) − x1( 3 ) = 1.00000 – 0.99958 = 0.00042,, x 2( 4 ) − x 2( 3 ) = 1.99999 – 1.99979 = 0.00020,, , x 3( 4 ) − x 3( 3 ) = 3.00000 – 3.00012 = 0.00012., Since, all the errors in magnitude are less than 0.0005, the required solution is, x1 = 1.0, x2 = 1.99999, x3 = 3.0., Rounding to three decimal places, we get x1 = 1.0, x2 = 2.0, x3 = 3.0., Example 1.23 Computationally show that Gauss-Seidel method applied to the system of, equations, 3x1 – 6x2 + 2x3 = 23, – 4x1 + x2 – x3 = – 8, x1 – 3x2 + 7x3 = 17, diverges. Take the initial approximations as x1 = 0.9, x2 = – 3.1, x3 = 0.9. Interchange the first, and second equations and solve the resulting system by the Gauss-Seidel method. Again take, the initial approximations as x1 = 0.9, x2 = – 3.1, x3 = 0.9, and obtain the result correct to two, decimal places. The exact solution is x1 = 1.0, x2 = – 3.0, x3 = 1.0., Solution Note that the system of equations is not diagonally dominant. Gauss-Seidel method, gives the iteration, x1(k+1) = [23 + 6x2(k) – 2x3(k))]/3, x2(k+1) = [– 8 + 4x1(k+1) + x3(k)]
Page 60 :
SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , 49, , x3(k+1) = [17 – x1(k+1) + 3x2(k+1)]/7., Starting with the initial approximations x1 = 0.9, x2 = – 3.1, x3 = 0.9, we obtain the, following results., First iteration, x1(1) =, , 1, 1, [23 + 6x2(0) – 2x3(0)] = [23 + 6(– 3.1) – 2(0.9)] = 0.8667,, 3, 3, , x2(1) = [– 8 + 4x1(1) + x3(0)] = [– 8 + 4(0.8667) + 0.9] = – 3.6332,, x3(1) =, , 1, 1, [17 – x1(1) + 3x2(1)] = [17 – (0.8667) + 3(– 3.6332)] = 0.7477., 7, 7, , Second iteration, x1(2) =, , 1, 1, [23 + 6x2(1) – 2x3(1)] = [23 + 6 (– 3.6332) – 2(0.7477)] = – 0.0982,, 3, 3, , x2(2) = [– 8 + 4x1(2) + x3(1)] = [– 8 + 4(– 0.0982) + 0.7477] = – 7.6451,, x3(2) =, , 1, 1, [17 – x1(2) + 3x2(2)] = [17 + 0.0982 + 3(– 7.6451)] = – 0.8339., 7, 7, , Third iteration, x1(3) =, , 1, 1, [23 + 6x2(2) – 2x3(2)] = [23 + 6 (– 7.6451) – 2(– 0.8339)] = – 7.0676,, 3, 3, , x2(3) = [– 8 + 4x1(3) + x3(2)] = [– 8 + 4(– 7.0676) – 0.8339] = – 37.1043,, x3(3) =, , 1, 1, [17 – x1(3) + 3x2(3)] = [17 + 7.0676 + 3(– 37.1043)] = – 12.4636., 7, 7, , It can be observed that the iterations are diverging very fast., Now, we exchange the first and second equations to obtain the system, – 4x1 + x2 – x3 = – 8, 3x1 – 6x2 + 2x3 = 23, x1 – 3x2 + 7x3 = 17., The system of equations is now diagonally dominant. Gauss-Seidel method gives iteration, x1(k+1) = [8 + x2(k) – x3(k)]/4, x2(k+1) = – [23 – 3x1(k+1) – 2x3(k)]/6, x3(k+1) = [17 – x1(k+1) + 3x2(k+1)]/7., Starting with the initial approximations x1 = 0.9, x2 = – 3.1, x3 = 0.9, we obtain the, following results., First iteration, x1(1) =, , 1, 1, [8 + x2(0) – x3(0)] = [8 – 3.1 – 0.9] = 1.0,, 4, 4
Page 61 :
50, , NUMERICAL METHODS, , x2(1) = –, x3(1) =, , 1, 1, [23 – 3x1(1) – 2x3(0)] = –, [23 – 3(1.0) – 2(0.9)] = – 3.0333,, 6, 6, , 1, 1, [17 – x1(1) + 3x2(1)] =, [17 – 1.0 + 3(– 3.0333)] = 0.9857., 7, 7, , Second iteration, x1(2) =, , 1, 1, [8 + x2(1) – x3(1)] =, [8 – 3.0333 – 0.9857] = 0.9953,, 4, 4, , x2(2) = –, x3(2) =, , 1, 1, [23 – 3x1(2) – 2x3(1)] = –, [23 – 3(0.9953) – 2(0.9857)] = – 3.0071,, 6, 6, , 1, 1, [17 – x1(2) + 3x2(2)] =, [17 – 0.9953 + 3(– 3.0071)] = 0.9976., 7, 7, , Third iteration, x1(3) =, , 1, 1, [8 + x2(2) – x3(2)] =, [8 – 3.0071 – 0.9976] = 0.9988,, 4, 4, , x2(3) = –, x3(3) =, , 1, 1, [23 – 3x1(3) – 2x3(2)] = –, [23 – 3(0.9988) – 2(0.9976)] = – 3.0014,, 6, 6, , 1, 1, [17 – x1(3) + 3x2(3)] =, [17 – 0.9988 + 3(– 3.0014)] = 0.9996., 7, 7, , Fourth iteration, x1(4) =, , 1, 1, [8 + x2(3) – x3(3)] =, [8 – 3.0014 – 0.9996] = 0.9998,, 4, 4, , x2(4) = –, x3(4) =, We find, , 1, 1, [23 – 3x1(4) – 2x3(3)] = –, [23 – 3(0.9998) – 2(0.9996)] = – 3.0002,, 6, 6, , 1, 1, [17 – x1(4) + 3x2(4)] =, [17 – 0.9998 + 3(– 3.0002)] = 0.9999., 7, 7, , x1( 4 ) − x1( 3 ) = 0.9998 – 0.9988 = 0.0010,, x 2( 4 ) − x 2( 3 ) = – 3.0002 + 3.0014 = 0.0012,, x 3( 4 ) − x 3( 3 ) = 0.9999 – 0.9996 = 0.0003., , Since, all the errors in magnitude are less than 0.005, the required solution is, x1 = 0.9998, x2 = – 3.0002, x3 = 0.9999., Rounding to two decimal places, we get x1 = 1.0, x2 = – 3.0, x3 = 1.0.
Page 62 :
51, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , REVIEW QUESTIONS, 1. Define an iterative procedure for solving a system of algebraic equations Ax = b. What, do we mean by convergence of an iterative procedure?, Solution A general linear iterative method for the solution of the system of equations, Ax = b can be written in matrix form as, x(k+1) = Hx(k) + c, k = 0, 1, 2, ..., where x(k+1) and x(k) are the approximations for x at the (k + 1)th and kth iterations, respectively. H is called the iteration matrix depending on A and c, which is a column, vector depends on A and b. We start with an initial approximation to the solution vector x = x0, and obtain a sequence of approximate vectors x0, x1 ,..., xk, ... We say that the, iteration converges if in the limit as k → ∞, the sequence of approximate vectors x0,, x1,..., xk,... converge to the exact solution vector x = A–1 b., 2. How do we terminate an iterative procedure for the solution of a system of algebraic, equations Ax = b ?, Solution We terminate an iteration procedure when the magnitudes of the differences, between the two successive iterates of all the variables are smaller than a given accuracy or an error bound ε, that is,, , x i( k + 1) − x i( k ) ≤ ε, for all i., For example, if we require two decimal places of accuracy, then we iterate until, , x i( k + 1) − x i( k ) < 0.005, for all i. If we require three decimal places of accuracy, then we, ( k + 1), − x i( k ), iterate until x i, , < 0.0005, for all i., , 3. What is the condition of convergence of an iterative procedure for the solution of a, system of linear algebraic equations Ax = b ?, Solution A sufficient condition for convergence of an iterative method is that the system of equations is diagonally dominant, that is, the coefficient matrix A is diagonally, n, , dominant. We can verify that | aii | ≥, , ∑ |a, , ij |., , This implies that convergence may be, , j =1, i ≠ j, , obtained even if the system is not diagonally dominant. If the system is not diagonally, dominant, we may exchange the equations, if possible, such that the new system is, diagonally dominant and convergence is guaranteed. The necessary and sufficient condition for convergence is that the spectral radius of the iteration matrix H is less than, one unit, that is, ρ(H) < 1, where ρ(H) is the largest eigen value in magnitude of H., 4. Which method, Gauss-Jacobi method or Gauss-Seidel method converges faster, for the, solution of a system of algebraic equations Ax = b ?, Solution If both the Gauss-Jacobi and Gauss-Seidel methods converge, then GaussSeidel method converges at least two times faster than the Gauss-Jacobi method.
Page 65 :
54, , NUMERICAL METHODS, , LM, MN, , Ak+1v = λk1+1 c1 v1 + c2, , Fλ I, GH λ JK, 2, , 1, , k +1, , v 2 + ... + cn, , Fλ I, GH λ JK, , k +1, , n, , 1, , OP, PQ, , vn ., , (1.55), , 1, As k → ∞, the right hand sides of (1.54) and (1.55) tend to λk1 c1v1 and λk+, 1 c1v1, since, λi / λ1 < 1, i = 2, 3, …, n. Both the right hand side vectors in (1.54), (1.55), , [c1v1 + c2(λ2 / λ1)k v2 + ... + cn (λn / λ1)k vn],, and, , [c1v1 + c2(λ2 / λ1)k+1 v2 + ... + cn (λn / λ1)k+1 vn], , tend to c1v1, which is the eigen vector corresponding to λ1. The eigen value λ1 is obtained as, the ratio of the corresponding components of Ak+1v and Akv. That is,, λ1 = lim, , k→∞, , ( A k +1v )r, ( A k v )r, , , r = 1, 2, 3, ..., n, , (1.56), , where the suffix r denotes the rth component of the vector. Therefore, we obtain n ratios, all of, them tending to the same value, which is the largest eigen value in magnitude, λ1 ., When do we stop the iteration The iterations are stopped when all the magnitudes of the, differences of the ratios are less than the given error tolerance., Remark 24 The choice of the initial approximation vector v0 is important. If no suitable, approximation is available, we can choose v0 with all its components as one unit, that is,, v0 = [1, 1, 1,..., 1]T. However, this initial approximation to the vector should be non-orthogonal, to v1., Remark 25 Faster convergence is obtained when λ2 << λ1 ., As k → ∞ , premultiplication each time by A, may introduce round-off errors. In order to, keep the round-off errors under control, we normalize the vector before premultiplying by A., The normalization that we use is to make the largest element in magnitude as unity. If we use, this normalization, a simple algorithm for the power method can be written as follows., yk+1 = Avk,, , (1.57), , vk+1 = yk+1 /mk+1, , (1.58), , where mk+1 is the largest element in magnitude of yk+1. Now, the largest element in magnitude of vk+1 is one unit. Then (1.56) can be written as, λ1 = lim, , k→∞, , (y k + 1 ) r, , r = 1, 2, 3, ...., n, (v k ) r, , (1.59), , and vk+1 is the required eigen vector., Remark 26 It may be noted that as k → ∞ , mk+1 also gives λ1 ., Remark 27 Power method gives the largest eigen value in magnitude. If the sign of the eigen, value is required, then we substitute this value in the determinant A – λ1I and find its, value. If this value is approximately zero, then the eigen value is of positive sign. Otherwise,, it is of negative sign., Example 1.24 Determine the dominant eigen value of A =, , LM1 2OP by power method., N3 4Q, , (A.U. Nov/Dec 2004)
Page 67 :
56, , NUMERICAL METHODS, , We obtain the ratios as, , 2.45743, = 5.37225, 5.37229., 0.45743, The magnitude of the error between the ratios is | 5.37225 – 5.37229 | = 0.00004, < 0.00005. Hence, the dominant eigen value, correct to four decimal places is 5.3722., Example 1.25 Determine the numerically largest eigen value and the corresponding eigen, vector of the following matrix, using the power method., , LM25, MN 12, , 1, 3, 0, , 2, 0, −4, , OP, PQ, , (A.U. May/June 2006), , Solution Let the initial approximation to the eigen vector be v0. Then, the power method is, given by, yk+1 = Avk,, vk+1 = yk+1 / mk+1, where mk+1 is the largest element in magnitude of yk+1. The dominant eigen value in magnitude is given by, λ1 = lim, , ( y k + 1 )r, ( v k )r, , k→∞, , ,, , r = 1, 2, 3, …, n, , and vk+1 is the required eigen vector., Let the initial approximation to the eigen vector be v0 = [1, 1, 1]T. We have the following, results., , LM25, MN 12, , OP LM OP LM OP, PQ MN PQ MN PQ, L 28 O L 1 OP, 1 M P M, 1, 4 = 0.14286 ., v =, y =, 28 M− 2P M− 0.07143P, m, N Q N, Q, L25 1 2 O L 1 O L25.0000O, y = Av = M 1 3 0 P M 0.14286 P = M1.42858P , m, MN 2 0 − 4PQ MN− 0.07143PQ MN2.28572PQ, L25.00000OP LM 1 OP, 1 M, 1, 1.14286 = 0.05714 ,, v =, y =, 25.0 M, m, N 2.28572 PQ MN0.09143PQ, L25 1 2 O L 1 O L25.24000O, y = Av = M 1 3 0 P M0.05714P = M 1.17142 P , m, MN 2 0 − 4PQ MN0.09143PQ MN 1.63428 PQ, y1 = Av0 =, , 1, , 2, , 2, , 3, , 28, 1 2 1, 3 0 1 = 4 , m1 = 28,, 0 −4 1, −2, , 1, , 1, , 1, , 2, , 2, , 2, , = 25.0,, , 3, , = 25.24,, , 2
Page 69 :
58, , NUMERICAL METHODS, , We obtain the ratios as, 25.18214,, , 1.72588, 1.13524, = 25.18279,, = 25.18430., 0.06853, 0.04508, , The magnitudes of the errors of the differences of these ratios are 0.00065, 0.00216,, 0.00151, which are less than 0.005. Hence, the results are correct to two decimal places. Therefore, the largest eigen value in magnitude is | λ1 | = 25.18., The corresponding eigen vector is v8,, v8 =, , LM, MN, , OP, PQ, , LM, MN, , OP, PQ, , 25.18214, 1, 1, 1, 1.13524 = 0.04508 ., y8 =, 25.18214, m8, 1.72588, 0.06854, , In Remark 26, we have noted that as k → ∞, mk+1 also gives | λ1 |. We find that this, statement is true since | m8 – m7 | = | 25.18214 – 25.18220 | = 0.00006., If we require the sign of the eigen value, we substitute λ1 in the characteristic equation., In the present problem, we find that | A – 25.18 I | = 1.4018, while | A + 25.18 I | is very, large. Therefore, the required eigen value is 25.18., , REVIEW QUESTIONS, 1. When do we use the power method?, Solution We use the power method to find the largest eigen value in magnitude and, the corresponding eigen vector of a matrix A., 2. Describe the power method., Solution Power method can be written as follows., yk+1 = Avk,, vk+1 = yk+1/mk+1, where mk+1 is the largest element in magnitude of yk+1. Now, the largest element in, magnitude of vk+1 is one unit. The largest eigen value in magnitude is given by, λ1 = lim, , k→∞, , ( y k +1 )r, ,, ( v k )r, , r = 1, 2, 3, …, n, , and vk+1 is the required eigen vector. All the ratios in the above equation tend to the, same number., 3. When do we stop the iterations in power method?, Solution Power method can be written as follows., yk+1 = Avk,, vk+1 = yk+1 / mk+1, where, , mk +1 is the largest element in magnitude of yk+1. Now, the largest element in, , magnitude of vk+1 is one unit. The largest eigen value is given by
Page 70 :
59, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , λ1 = lim, , k→∞, , ( y k +1 )r, , r = 1, 2, 3, …, n, ( v k )r, , and vk+1 is the required eigen vector. All the ratios in the above equation tend to the, same number. The iterations are stopped when all the magnitudes of the differences of, the ratios are less than the given error tolerance., 4. When can we expect faster convergence in power method?, Solution To apply power method, we assume | λ1 | > | λ2 | > ... > | λn |. Faster, convergence is obtained when | λ2 | << | λ1 |. That is, the leading eigen value in, magnitude is much larger than the remaining eigen values in magnitudes., 5. Does the power method give the sign of the largest eigen value?, Solution No. Power method gives the largest eigen value in magnitude. If the sign of, the eigen value is required, then we substitute this value in the characteristic determinant | A – λ1I | and determine the sign of the eigen value. If | A – λ1I | = 0 is satisfied, approximately, then it is of positive sign. Otherwise, it is of negative sign., , EXERCISE 1.4, Determine the largest eigen value in magnitude and the corresponding eigen vector of, the following matrices by power method. Use suitable initial approximation to the eigen, vector., , 1., , 3., , 6., , LM 1 3, MN−31 42, LM35 2, MN 21 03, LM15 2, MN 00 30, , OP, PQ, 1O, 0 P., − 1PQ, 1O, 2 P., − 1PQ, , −1, 4 ., 10, , (A.U. Nov/Dec 2003), , LM1, 2. 4, MN6, , LM20 1 1OP, MN 11 03 01PQ ., L3 1 5 O, 7. M1 0 2 P ., MN5 2 − 1PQ, 4., , OP, PQ, , −3 2, 4 −1, 3, 5, , (A.U. Apr/May 2005), , LM, MN, L65, 8. M 0, MN 1, , OP, PQ, 1O, 0P ., 2PQ, , 6 1 0, 5. 1 40 1 ., 0 1 6, 0, 5, 0, , 1.4 ANSWERS AND HINTS, Exercise 1.1, 1. (2, 3); x0 = 2, x1 = 3, x2 = 2.058824, x3 = 2.081264, x4 = 2.089639, x5 = 2.092740., 2. (2, 3); x0 = 2, x1 = 3, x2 = 2.721014, x3 = 2.740205, x4 = 2.740637, | x4 – x3 | = 0.000432., Root correct up to 4 decimal places is x4., 3. x0 = 2.5, x1 = 3, x2 = 2.801252, x3 = 2.798493, x4 = 2.798390, | x4 – x3 | = 0.000103. Root, correct up to 3 decimal places is x4.
Page 72 :
61, , SOLUTION OF EQUATIONS AND EIGEN VALUE PROBLEMS, , 20. (0, 1); xk+1 = [(1 + cos xk)/3] = φ(xk), k = 0, 1, 2,... x0 = 0, x1 = 0.666667,, x2 = 0.595296, x3 = 0.609328, x4 = 0.606678, x5 = 0.607182, x6 = 0.607086,, | x6 – x5 | = 0.000096. Root correct up to 3 decimal places is x6., 21. We have α + β = – a, α β = b., (i) φ(x) = –, , ax + b, b, αβ, , φ′(x) = – 2 = − 2 . For convergence to α, we have, x, x, x, , | φ′(α) | = | – (αβ)/α2 | < 1, or, (ii) φ(x) = –, , | α | > | β |., , αβ, b, b, =, , φ′(x) =, . For convergence to α, we have, ( x + a) 2 ( x − α − β) 2, x+a, , | φ′(α) | = | (αβ)/β2 | < 1,, , or | α | < | β |., , Exercise 1.2, 1. x = 1.70869, y = – 1.80032, z = 1.04909. 2. x = – 4.5, y = 2.5, z = 5., 3. x = 1, y = – 5, z = 1., , 4. x1 = 1, x2 = – 1, x3 = – 1, x4 = 1., , 5. x = 1, y = 1, z = 1., , 6. x = 1, y = 2, z = 3., , 7. x = 1, y = – 5, z = 1., , 8. x = 1, y = 1/2, z = – 1/2., , 9., , 11., , LM, MN, , OP, PQ, , LM, MN, 5, 1L, 12. M 5, 5 M− 5, N, , −6, −1, 5, 1, 24 − 17 3 ., 2 − 10, −1, 7, 1, 56, , LM12, MN 51, , OP, PQ, , 10., , 4, 6, 5 −3 ., −3 −1, , OP, PQ, , 24, 8 12, 1, − 10 − 2 − 6 ., 8 −2 −2 −2, , OP, PQ, , −1 −2, −1 −7 ., 2, 4, , In Problems 13-16, Gauss elimination gives the following results., 13., , 14., , 15., , LM2, MN00, LM1, MN00, LM2, MN00, , OP, PQ, , −3 0, 1, 11 / 2 17 / 2 14 ; rank (A) = 2; rank (A|b) = 3. The system is inconsistent., −3, 0, 0, , OP, PQ, , −3 4 2, 4 − 5 − 2 ; rank (A) = 2; rank (A|b) = 3. The system is inconsistent., 0, 0 2, , OP, PQ, , −3 2, 1, 11 / 2 17 / 2 14 ; rank (A) = 2; rank (A|b) = 2. The system is consistent and has, 0, 0, 0, , one parameter family of solutions., 16., , LM1, MN00, , OP, PQ, , 5 −1 0, − 7 3 11 ; rank (A) = 2; rank (A|b) = 2. The system is consistent and has one, 0, 0 0, , parameter family of solutions.
Page 73 :
62, , NUMERICAL METHODS, , Exercise 1.3, In all the Problems, values for four iterations have been given. Solutions are the transposes of, the given vectors., 1., , [0, 0, 0], [0.85, – 0.9, 1.25], [1.02, – 0.965, 1.03], [1.00125, – 1.0015, 1.00325],, [1.00040, – 0.99990, 0.99965]. Exact: [1, – 1, 1]., , 2., , [0, 0, 0], [3.14815, 4.8, 2.03704], [2.15693, 3.26913, 1.88985], [2.49167, 3.68525, 1.93655],, [2.40093, 3.54513, 1.92265]., , 3., , Exchange the first and second rows. [0, 0, 0], [0.76, – 0.9, 0.875], [0.971, – 0.98175,, 1.04], [1.00727, – 1.00055, 1.00175], [1.00037, – 1.00045, 0.99755]. Exact: [1, – 1, 1]., , 4., , [0, 0, 0], [2.0, 2.33333, 0.28571], [1.12381, 1.85714, – 1.33333], [0.99048, 1.94127,, – 0.93605], [1.03628, 2.00771, – 0.96508]. Exact: [1, 2, – 1]., , 5., , [0, 0, 0], [3.14815, 3.54074, 1.91317], [2.43218, 3.57204, 1.92585], [2.42569, 3.57294,, 1.92595], [2.42549, 3.57301, 1.92595]., , 6., , [0, 0, 0], [3.5, 1.3, 1.9], [2.375, 1.905, 1.965], [2.05625, 1.98175, 1.99525], [2.01031,, 1.99700, 1.99909]. Exact: [2, 2, 2]., , 7., , Interchange first and third rows. [1, – 1, 3], [1.32829, – 2.36969, 3.44982], [1.22856,, – 2.34007, 3.45003], [1.22999, – 2.34000, 3.45000], [1.23000, – 2.34000, 3.45000]., , 8., , [0, 0, 0], [0.85, – 1.0275, 1.01088], [0.89971, – 0.98441, 1.01237], [0.90202, – 0.98468,, 1.01210], [0.90200, – 0.98469, 1.01210]., , 9., , Interchange first and second rows. [0, 0, 0], [0.76, – 0.938, 1.059], [1.00932, – 1.00342,, 0.99821], [0.99978, – 0.99990, 1.00003], [1.0, – 1.0, 1.0]., , 10., , [0, 0, 0], [2.0, 1.83333, – 1.04762], [1.05714, 1.98175, – 0.99773], [1.00775, 1.99825,, – 1.00011], [1.00068, 1.99982, – 0.99989]. Exact: [1, 2, – 1]., , Exercise 1.4, In all problems, we have taken v(0) = [1, 1, 1]. The results obtained after 8 iterations are given., Solutions are the transposes of the given vectors., 1. | λ | = 11.66, v = [0.02496, 0.42180, 1.0]. 2. | λ | = 6.98, v = [0.29737, 0.06690, 1.0]., 3. | λ | = 35.15, v = [1.0, 0.06220, 0.02766]. 4. | λ | = 20.11, v = [1.0, 0.05316, 0.04759]., 5. | λ | = 40.06, v = [0.02936, 1.0, 0.02936]. 6. | λ | = 15, v = [1.0, 0.00002, 0.0]., 7. | λ | = 6.92, v = [1.0, 0.35080, 0.72091]., , 8. | λ | = 65.02, v = [1.0, 0.0, 0.01587].
Page 74 :
Interpolation and Approximation, , 2.1, , INTRODUCTION, , In this chapter, we discuss the problem of approximating a given function by polynomials., There are two main uses of these approximating polynomials. The first use is to reconstruct, the function f(x) when it is not given explicitly and only values of f(x) and/ or its certain order, derivatives are given at a set of distinct points called nodes or tabular points. The second use, is to perform the required operations which were intended for f(x), like determination of roots,, differentiation and integration etc. can be carried out using the approximating polynomial, P(x). The approximating polynomial P(x) can be used to predict the value of f(x) at a nontabular point. The deviation of P(x) from f(x), that is f(x) – P(x), is called the error of approximation., Let f(x) be a continuous function defined on some interval [a, b], and be prescribed, at n + 1 distinct tabular points x0, x1,..., xn such that a = x0 < x1 < x2 < ... < xn = b. The distinct, tabular points x0, x1,..., xn may be non-equispaced or equispaced, that is xk+1 – xk = h, k = 0, 1,, 2,…, n –1. The problem of polynomial approximation is to find a polynomial Pn(x), of degree, ≤ n, which fits the given data exactly, that is,, Pn(xi) = f(xi),, , i = 0, 1, 2,…, n., , (2.1), , The polynomial Pn(x) is called the interpolating polynomial. The conditions given in, (2.1) are called the interpolating conditions., Remark 1 Through two distinct points, we can construct a unique polynomial of degree 1, (straight line). Through three distinct points, we can construct a unique polynomial of degree, 2 (parabola) or a unique polynomial of degree1 (straight line). That is, through three distinct, points, we can construct a unique polynomial of degree ≤ 2. In general, through n + 1 distinct, points, we can construct a unique polynomial of degree ≤ n. The interpolation polynomial, fitting a given data is unique. We may express it in various forms but are otherwise the same, polynomial. For example, f(x) = x2 – 2x – 1 can be written as, x2 – 2x – 1 = – 2 + (x – 1) + (x – 1) (x – 2)., , 63
Page 76 :
65, , INTERPOLATION AND APPROXIMATION, , Hence,, Therefore,, , C=, li(x) =, , 1, ., ( x i − x 0 ) ( x i − x1 )...( x i − x i −1 ) ( x i − x i +1 )...( x i − x n ), ( x − x 0 ) ( x − x1 )...( x − x i −1 )( x − x i +1 )...( x − x n ), ( x i − x 0 ) ( x i − x1 )...( x i − x i −1 ) ( x i − x i +1 )...( x i − x n ), , (2.4), , Note that the denominator on the right hand side of li(x) is obtained by setting x = xi in, the numerator., The polynomial given in (2.2) where li(x) are defined by (2.4) is called the Lagrange, interpolating polynomial and li(x) are called the Lagrange fundamental polynomials., We can write the Lagrange fundamental polynomials li(x) in a simple notation., Denote, , w(x) = (x – x0) (x – x1)...(x – xn), , which is the product of all factors. Differentiating w(x) with respect to x and substituting x = xi, we get, w′(xi) = (xi – x0) (xi – x1)...(xi – xi–1) (xi – xi+1)...(xi – xn), since all other terms vanish. Therefore, we can also write li(x) as, li(x) =, , w( x ), ., ( x − x i ) w′ ( x i ), , (2.5), , Let us derive the linear and quadratic interpolating polynomials., Linear interpolation, For n = 1, we have the data, x, , x0, , x1, , f(x), , f(x0), , f(x1), , The Lagrange fundamental polynomials are given by, l0(x) =, , ( x − x1 ), (x − x0 ), , l1(x) =, ., ( x 0 − x1 ), ( x1 − x 0 ), , (2.6), , The Lagrange linear interpolation polynomial is given by, P1(x) = l0(x) f(x0) + l1(x) f(x1)., , (2.7), , Quadratic interpolation, For n = 2, we have the data, x, , x0, , x1, , x2, , f(x), , f(x0), , f(x1), , f(x2), , The Lagrange fundamental polynomials are given by, l0(x) =, , ( x − x1 ) ( x − x 2 ), ( x − x 0 ) ( x − x1 ), ( x − x0 ) (x − x2 ), , l (x) =, , l (x) =, ., ( x 0 − x1 ) ( x 0 − x 2 ) 1, ( x 2 − x 0 ) ( x 2 − x1 ), ( x1 − x 0 ) ( x1 − x 2 ) 2
Page 77 :
66, , NUMERICAL METHODS, , The Lagrange quadratic interpolation polynomial is given by, P1(x) = l0(x) f(x0) + l1(x) f(x1) + l2(x) f(x2)., , (2.8), , Error of interpolation, We assume that f(x) has continuous derivatives of order up to n + 1 for all x ∈ (a, b)., Since, f(x) is approximated by Pn(x), the results contain errors. We define the error of interpolation or truncation error as, E(f, x) = f(x) – Pn(x)., , (2.9), , Without giving the derivation, we write the expression for the error of interpolation as, E(f, x) = f(x) – Pn(x), =, , ( x − x 0 ) ( x − x1 )...( x − x n ), w( x ), f (n+1) (ξ) =, f (n+1) (ξ) (2.10), (n + 1) !, ( n + 1) !, , where min(x0, x1,..., xn, x) < ξ < max(x0, x1,..., xn, x)., Since, ξ is an unknown, it is difficult to find the value of the error. However, we can find, a bound of the error. The bound of the error is obtained as, | E(f, x) | =, , ≤, , 1, | (x – x0) (x – x1)...(x – xn) | | f (n+1) (ξ) |, ( n + 1) !, , LM, N, , OP LMmax | f, QN, , 1, max | ( x − x 0 ) ( x − x1 ) ...( x − x n ) |, (n + 1) ! a ≤ x ≤b, , a ≤ x ≤b, , ( n +1 ), , OP, Q, , (x) |, , (2.11), , Note that in (2.11), we compute the maximum absolute value of, w(x) = (x – x0)(x – x1)...(x – xn), that is max | w(x) | and not the maximum of w(x)., Since the interpolating polynomial is unique, the error of interpolation is also unique,, that is, the error is same whichever form of the polynomial is used., Example 2.1 Using the data sin(0.1) = 0.09983 and sin (0.2) = 0.19867, find an approximate, value of sin (0.15) by Lagrange interpolation. Obtain a bound on the error at x = 0.15., Solution We have two data values. The Lagrange linear polynomial is given by, P1(x) =, =, , Hence,, , ( x − x1 ), (x − x0 ), f(x0) +, f(x1), ( x 0 − x1 ), ( x1 − x 0 ), , ( x − 0.2), ( x − 0.1), (0.09983) +, (0.19867)., ( 0.1 − 0.2), ( 0.2 − 0.1), , f(0.15) = P1(0.15) =, , ( 0.15 − 0.2), ( 0.15 − 0.1), (0.09983) +, (0.19867), ( 0.1 − 0.2), ( 0.2 − 0.1), , = (0.5) (0.09983) + (0.5) (0.19867) = 0.14925.
Page 78 :
67, , INTERPOLATION AND APPROXIMATION, , The truncation error is given by, T.E =, , ( x − x 0 ) ( x − x1 ), ( x − 0.1) ( x − 0.2 ), f ″(ξ) =, (– sin ξ),, 2, 2, , 0.1 < ξ < 0.2., , since f(x) = sin x. At x = 0.15, we obtain the bound as, T.E =, and, , (0.15 − 0.1) (0.15 − 0.2), (– sin ξ) = 0.00125 sin ξ, 2, , | T.E | = 0.00125 | sin ξ | ≤ 0.00125 max | sin x |, 0.1≤ x ≤ 0.2, , = 0.00125 sin (0.2) = 0.00125(0.19867) = 0.00025., Example 2.2 Use Lagrange’s formula, to find the quadratic polynomial that takes the values, x, , 0, , 1, , 3, , y, , 0, , 1, , 0, , (A.U Nov/Dec. 2005), , Solution Since f0 = 0 and f2 = 0, we need to compute l1(x) only. We have, l1(x) =, , ( x − x0 ) (x − x2 ), x ( x − 3) 1, =, = (3x – x2)., ( x 1 − x 0 ) ( x 1 − x 2 ) (1) ( − 2 ) 2, , The Lagrange quadratic polynomial is given by, f(x) = l1(x) f(x1) =, , 1, 1, (3x – x2) (1) =, (3x – x2)., 2, 2, , Example 2.3 Given that f(0) = 1, f(1) = 3, f(3) = 55, find the unique polynomial of degree 2 or, less, which fits the given data., Solution We have x0 = 0, f0 = 1, x1 = 1, f1 = 3, x2 = 3, f2 = 55. The Lagrange fundamental, polynomials are given by, l0(x) =, , ( x − x1 ) ( x − x 2 ), ( x − 1) ( x − 3 ) 1 2, =, = (x – 4x + 3)., ( x 0 − x1 ) ( x 0 − x 2 ), ( − 1) ( − 3 ), 3, , l1(x) =, , (x − x0 ) (x − x2 ), x ( x − 3) 1, =, = (3x – x2)., ( x 1 − x 0 ) ( x1 − x 2 ) (1) ( − 2) 2, , l2(x) =, , ( x − x 0 ) ( x − x1 ), x ( x − 1) 1 2, =, = (x – x)., ( x 2 − x 0 ) ( x 2 − x1 ), (3) ( 2), 6, , Hence, the Lagrange quadratic polynomial is given by, P2(x) = l0(x) f(x0) + l1(x) f(x1) + l2(x) f(x2), =, , 1 2, 1, 55 2, (x – 4x + 3) +, (3x – x2) (3) +, (x – x) = 8x2 – 6x + 1., 3, 2, 6
Page 79 :
68, , NUMERICAL METHODS, , Example 2.4 The following values of the function f(x) = sin x + cos x, are given, x, , 10°, , 20°, , 30°, , f(x), , 1.1585, , 1.2817, , 1.3660, , Construct the quadratic Lagrange interpolating polynomial that fits the data. Hence, find, f (π/12). Compare with the exact value., Solution Since the value of f at π /12 radians is required, we convert the data into radian, measure. We have, x0 = 10° =, , π, π, π, = 0.1745, x1 = 20° =, = 0.3491, x2 = 30° =, = 0.5236., 18, 9, 6, , The Lagrange fundamental polynomials are given by, l0(x) =, , ( x − x1 ) ( x − x 2 ), ( x − 0.3491) ( x − 0.5236 ), =, ( x 0 − x1 ) ( x 0 − x 2 ), ( − 01746, ., ) ( − 0.3491), , = 16.4061 (x2 – 0.8727x + 0.1828)., l1(x) =, , ( x − x0 ) (x − x2 ), ( x − 0.1745) ( x − 0.5236 ), =, ( x1 − x 0 ) ( x1 − x 2 ), ( 0.1746) ( − 0.1745), , = – 32.8216(x2 – 0.6981x + 0.0914)., l2(x) =, , ( x − x 0 ) ( x − x1 ), ( x − 0.1745) ( x − 0.3491), =, ( x 2 − x 0 ) ( x 2 − x1 ), ( 0.3491) ( − 0.1745), , = 16.4155(x2 – 0.5236x + 0.0609)., The Lagrange quadratic polynomial is given by, P2(x) = l0(x) f(x0) + l1(x) f(x1) + l2(x) f(x2), = 16.4061(x2 – 0.8727x + 0.1828) (1.1585) – 32.8616 (x2 – 0.6981x, + 0.0914) (1.2817) + 16.4155(x2 – 0.5236x + 0.0609) (1.3660), = – 0.6374x2 + 1.0394x + 0.9950., f(π/12) = f(0.2618) = 1.2234., The exact value is f(0.2618) = sin(0.2618) + cos(0.2618) = 1.2247., Example 2.5 Construct the Lagrange interpolation polynomial for the data, x, , –1, , 1, , 4, , 7, , f (x), , –2, , 0, , 63, , 342, , Hence, interpolate at x = 5., Solution The Lagrange fundamental polynomials are given by, l0(x) =, , ( x − x1 ) ( x − x 2 ) ( x − x 3 ), ( x − 1) ( x − 4 ) ( x − 7 ), =, −, −, −, −, ( x 0 x 1 ) ( x 0 x 2 ) ( x 0 x 3 ) ( 1 − 1) ( − 1 − 4 ) ( − 1 − 7 )
Page 80 :
69, , INTERPOLATION AND APPROXIMATION, , =–, l1(x) =, =, l2(x) =, , ( x − x 0 ) ( x − x 2 ) ( x − x3 ), ( x + 1) ( x − 4 ) ( x − 7), =, ( x1 − x 0 ) ( x1 − x 2 ) ( x1 − x 3 ), (1 + 1) (1 − 4 ) (1 − 7 ), 1, (x3 – 10x2 + 17x + 28)., 36, ( x − x 0 ) ( x − x1 ) ( x − x 3 ), ( x + 1) ( x − 1) ( x − 7 ), =, ( x 2 − x 0 ) ( x 2 − x1 ) ( x 2 − x 3 ) ( 4 + 1) ( 4 − 1) ( 4 − 7 ), , =–, l3(x) =, =, , 1, (x3 – 12x2 + 39x – 28)., 80, , 1, (x3 – 7x2 – x + 7)., 45, , ( x − x 0 ) ( x − x1 ) ( x − x 2 ), ( x + 1) ( x − 1) ( x − 4 ), =, ( x 3 − x 0 ) ( x 3 − x 1 ) ( x 3 − x 2 ) ( 7 + 1) ( 7 − 1) ( 7 − 4 ), 1, (x3 – 4x2 – x + 4)., 144, , Note that we need not compute l1(x) since f(x1) = 0., The Lagrange interpolation polynomial is given by, P3(x) = l0(x) f(x0) + l1(x) f(x1) + l2(x) f(x2) + l3(x) f(x3), =–, , 1, 1, (x3 – 12x2 + 39x – 28) (– 2) –, (x3 – 7x2 – x + 7) (63), 80, 45, , +, =, , 1, (x3 – 4x2 – x + 4) (342), 144, , FG 1 − 7 + 171IJ x + FG − 3 + 49 − 171IJ x + FG 39 + 7 − 171IJ x + FG − 7 − 49 + 171IJ, H 40 5 72 K H 10 5 18 K H 40 5 72 K H 10 5 8 K, 3, , 2, , = x3 – 1., Hence, f(5) = P3(5) = 53 – 1 = 124., Remark 2 For a given data, it is possible to construct the Lagrange interpolation polynomial., However, it is very difficult and time consuming to collect and simplify the coefficients of xi, i, = 0, 1, 2,…, n. Now, assume that we have determined the Lagrange interpolation polynomial, of degree n based on the data values (xi, f(xi)), i = 0, 1, 2,…, n at the (n + 1) distinct points., Suppose that to this given data, a new value (xn+1, f(xn+1)) at the distinct point xn+1 is added at, the end of the table. If we require the Lagrange interpolating polynomial for this new data,, then we need to compute all the Lagrange fundamental polynomials again. The nth degree, Lagrange polynomial obtained earlier is of no use. This is the disadvantage of the Lagrange, interpolation. However, Lagrange interpolation is a fundamental result and is used in proving many theoretical results of interpolation.
Page 81 :
70, , NUMERICAL METHODS, , Remark 3 Suppose that the data (xi, f(xi)), i = 0, 1, 2,…, n, is given. Assume that a new value, (xn+1, f(xn+1)) at the distinct point xn+1 is added at the end of the table. The data, (xi, f(xi)),, i = 0, 1, 2,…, n + 1, represents a polynomial of degree ≤ (n + 1). If this polynomial of degree, (n + 1) can be obtained by adding an extra term to the previously obtained nth degree interpolating polynomial, then the interpolating polynomial is said to have the permanence property., We observe that the Lagrange interpolating polynomial does not have the permanence property., Divided differences, Let the data, (xi, f(xi)), i = 0, 1, 2,…, n, be given. We define the divided differences as follows., First divided difference Consider any two consecutive data values (xi, f(xi)), (xi+1, f(xi+1)). Then,, we define the first divided difference as, f [xi, xi+1] =, Therefore,, Note that, , f [x0, x1] =, , f ( xi + 1 ) − f ( xi ), ,, xi + 1 − xi, f ( x1 ) − f ( x0 ), ,, x1 − x0, , f [xi, xi+1] = f [xi+1, xi] =, , i = 0, 1, 2,…, n – 1., f[x1, x2] =, , (2.12), , f ( x2 ) − f ( x1 ), etc., x2 − x1, , f ( xi ), f ( xi + 1 ), ., +, xi − xi + 1 xi + 1 − xi, , We say that the divided differences are symmetrical about their arguments., Second divided difference Consider any three consecutive data values (xi, f(xi)), (xi+1, f(xi+1)),, (xi+2, f(xi+2)). Then, we define the second divided difference as, f [xi xi+1, xi+2] =, Therefore,, , f [x0, x1, x2] =, , f [ xi + 1 , xi + 2 ] − f [ xi , xi + 1 ], xi + 2 − xi, , i = 0, 1, 2,…, n – 2, , (2.13), , f [ x1, x2 ] − f [ x0 , x1 ], etc., x2 − x0, , We can express the divided differences in terms of the ordinates. We have, f [x0, x1, x2] =, , 1, x2 − x0, , LM f, Nx, , 2, , 2, , − f1, f − f0, − 1, − x0 x1 − x0, , OP, Q, , LM, N, , OP, Q, , =, , f0, f1, f2, 1, 1, +, −, +, ( x0 − x1 )( x0 − x2 ) ( x2 − x0 ) x2 − x1 x1 − x0, ( x2 − x0 )( x2 − x1 ), , =, , f0, f1, f2, +, +, ( x0 − x1 )( x0 − x2 ) ( x1 − x0 )( x1 − x2 ) ( x2 − x0 )( x2 − x1 ), , Notice that the denominators are same as the denominators of the Lagrange fundamental polynomials. In general, we have the second divided difference as, f [xi xi+1, xi+2] =, , f [ xi + 1 , xi + 2 ] − f [ xi , xi + 1 ], xi + 2 − xi
Page 82 :
71, , INTERPOLATION AND APPROXIMATION, , fi, fi + 1, fi + 2, +, +, ( xi − xi + 1 )( xi − xi + 2 ) ( xi + 1 − xi )( xi + 1 − xi + 2 ) ( xi + 2 − xi )( xi + 2 − xi + 1 ), , =, , The nth divided difference using all the data values in the table, is defined as, , f [ x1 , x 2 ,..., x n ] − f [ x 0 , x1 ,..., x n −1], , f [x0, x1, ..., xn] =, , (2.14), , xn − x 0, , The nth divided difference can also be expressed in terms of the ordinates fi. The denominators of the terms are same as the denominators of the Lagrange fundamental polynomials., The divided differences can be written in a tabular form as in Table 2.1., Table 2.1. Divided differences (d.d)., x, , f(x), , x0, , f0, , x1, , f1, , First d.d, , Second d.d, , Third d.d, , f [x0, x1], f [x0, x1, x2], f [x1, x2], f2, , x2, , f [x0, x1, x2, x3], f [x1, x2, x3], , f [x2, x3], f3, , x3, , Example 2.6 Find the second divided difference of f(x) = 1/x, using the points a, b, c., Solution We have, , LM OP, N Q, f (c) − f (b), b− c, 1 L1 1O, 1, =−, =, − P=, f [b, c] =, ,, M, c−b, c − b N c b Q (c − b)bc, bc, f [b, c] − f [ a, b], c−a, 1 L 1, 1O, 1, =, −, +, =, =, ., f [a, b, c] =, M, P, c−a, c − a N bc ab Q ( c − a) abc abc, f[a, b] =, , f (b) − f ( a), a−b, 1, 1 1, 1, =, −, =, =−, ,, (b − a) ab, b−a, b− a b a, ab, , Example 2.7 Obtain the divided difference table for the data, x, , –1, , 0, , 2, , 3, , f (x ), , –8, , 3, , 1, , 12, , (A.U Nov/Dec 2006)
Page 85 :
74, , NUMERICAL METHODS, , = 1245 + (x + 4)(– 404) + (x + 4)(x + 1)(94) + (x + 4)(x + 1) x (– 14), + (x + 4)(x + 1) x (x – 2)(3), = 1245 – 404x – 1616 + (x2 + 5x + 4)(94) + (x3 + 5x2 + 4x)(– 14), + (x4 + 3x3 – 6x2 – 8x)(3), = 3x4 – 5x3 + 6x2 – 14x + 5., Divided difference table. Example 2.8., x, , f(x), , –4, , 1245, , First d.d, , Second d.d, , Third d.d, , Fourth d.d, , – 404, –1, , 33, , 0, , 5, , 94, – 28, , – 14, 10, , 3, , 2, 2, , 13, , 9, , 88, 442, , 5, , 1335, , Example 2.9 Find f(x) as a polynomial in x for the following data by Newton’s divided difference formula, x, f(x), , –2, , –1, , 0, , 1, , 3, , 4, , 9, , 16, , 17, , 18, , 44, , 81, , Hence, interpolate at x = 0.5 and x = 3.1., Solution We form the divided difference table for the given data., Since, the fourth order differences are zeros, the data represents a third degree polynomial. Newton’s divided difference formula gives the polynomial as, f(x) = f(x0) + (x – x0) f [x0, x1] + (x – x0)(x – x1) f [x0, x1, x2], + (x – x0)(x – x1) (x – x2) f [x0, x1, x2, x3], = 9 + (x + 2)(7) + (x + 2)(x + 1)(– 3) + (x + 2)(x + 1) x(1), = 9 + 7x + 14 – 3x2 – 9x – 6 + x3 + 3x2 + 2x = x3 + 17., Hence,, , f(0.5) = (0.5)3 + 17 = 17.125., f(3.1) = (3.1)3 + 17 = 47.791.
Page 86 :
75, , INTERPOLATION AND APPROXIMATION, , Divided difference table. Example 2.9., x, , f(x), , –2, , 9, , First d.d, , Second d.d, , Third d.d, , Fourth d.d, , 7, –1, , 16, , –3, 1, , 0, , 17, , 1, , 18, , 1, 0, , 0, , 1, , 1, 4, , 0, , 13, 3, , 1, , 44, , 8, 37, , 4, , 81, , Example 2.10 Find f(x) as a polynomial in x for the following data by Newton’s divided difference formula, x, , 1, , 3, , 4, , 5, , 7, , 10, , f(x), , 3, , 31, , 69, , 131, , 351, , 1011, , Hence, interpolate at x = 3.5 and x = 8.0. Also find, f′(3) and f″ (1.5)., Solution We form the divided difference table for the data., Divided difference table. Example 2.10., x, , f(x), , 1, , 3, , 3, , 31, , First d.d, , Second d.d, , Third d.d, , Fourth d.d, , 14, 8, 38, 4, , 69, , 1, 12, , 62, 5, , 131, , 16, 110, , 7, , 0, 1, , 351, , 0, 1, , 22, 220, , 10, , 1011, , Since, the fourth order differences are zeros, the data represents a third degree, polynomial. Newton’s divided difference formula gives the polynomial as
Page 87 :
76, , NUMERICAL METHODS, , f(x) = f(x0) + (x – x0) f [x0, x1] + (x – x0)(x – x1) f [x0, x1, x2], + (x – x0)(x – x1)(x – x2) f [x0, x1, x2, x3], = 3 + (x – 1)(14) + (x – 1)(x – 3)(8) + (x – 1)(x – 3)(x – 4)(1), = 3 + 14x – 14 + 8x2 – 32x + 24 + x3 – 8x2 + 19x – 12 = x3 + x + 1., f(3.5) ≈ P3(3.5) = (3.5)3 + 3.5 + 1 = 47.375,, , Hence, , f(8.0) ≈ P3(8.0) = (8.0)3 + 8.0 + 1 = 521.0., P′3(x) = 3x2 + 1, and P″3(x) = 6x., , Now,, Therefore,, , f ′(3) ≈ P′(3) = 3(9) + 1 = 28, f ″(1.5) ≈ P″(1.5) = 6(1.5) = 9., , Inverse interpolation, Suppose that a data (xi, f(xi)), i = 0, 1, 2,…, n, is given. In interpolation, we predict the, value of the ordinate f(x′) at a non-tabular point x = x′. In many applications, we require the, value of the abscissa x′ for a given value of the ordinate f(x′). For this problem, we consider the, given data as ( f (xi), xi), i = 0, 1, 2,…, n and construct the interpolation polynomial. That is, we, consider f(x) as the independent variable and x as the dependent variable. This procedure is, called inverse interpolation, , REVIEW QUESTIONS, 1. Give two uses of interpolating polynomials., Solution The first use is to reconstruct the function f(x) when it is not given explicitly, and only values of f(x) and/ or its certain order derivatives are given at a set of distinct, points called nodes or tabular points. The second use is to perform the required operations which were intended for f (x), like determination of roots, differentiation and integration etc. can be carried out using the approximating polynomial P(x). The approximating polynomial P(x) can be used to predict the value of f(x) at a non-tabular point., 2. Write the property satisfied by Lagrange fundamental polynomials li(x)., Solution The Lagrange fundamental polynomials li(x) satisfy the property, li(x) = 0, i ≠ j, = 1, i = j, 3. Write the expression for the bound on the error in Lagrange interpolation., Solution The bound for the error in Lagrange interpolation is given by, | E(f, x) | =, , 1, | (x – x0)(x – x1)...(x – xn) | | f (n+1) (ξ) |, (n + 1) !, , LM, N, , OP LM max |f, QN, , 1, max |( x − x 0 )( x − x1 ) ... ( x − x n )|, (n + 1) ! a ≤ x ≤ b, 4. What is the disadvantage of Lagrange interpolation?, ≤, , a≤x ≤b, , ( n +1 ), , OP, Q, , ( x )|, , Solution Assume that we have determined the Lagrange interpolation polynomial of degree, n based on the data values (xi, f(xi)), i = 0, 1, 2,…, n given at the (n + 1) distinct points.
Page 88 :
77, , INTERPOLATION AND APPROXIMATION, , Suppose that to this given data, a new value (xn+1, f(xn+1)) at the distinct point xn+1 is, added at the end of the table. If we require the Lagrange interpolating polynomial of, degree (n + 1) for this new data, then we need to compute all the Lagrange fundamental, polynomials again. The nth degree Lagrange polynomial obtained earlier is of no use., This is the disadvantage of the Lagrange interpolation., 5. Define the permanence property of interpolating polynomials., Solution Suppose that a data (xi, f(xi)), i = 0, 1, 2,…, n, is given. Assume that a new, value (xn+1, f(xn+1)) at the distinct point xn+1 is added at the end of the table. The data,, (xi, f(xi)), i = 0, 1, 2,…, n + 1, represents a polynomial of degree (n + 1). If this polynomial, of degree (n + 1) can be obtained by adding an extra term to the previously obtained nth, degree interpolating polynomial, then the interpolating polynomial is said to have the, permanence property., 6. Does the Lagrange interpolating polynomial have the permanence property?, Solution Lagrange interpolating polynomial does not have the permanence property., Suppose that to the given data (xi, f(xi)), i = 0, 1, 2,…, n, a new value (xn+1, f(xn+1)) at the, distinct point xn+1 is added at the end of the table. If we require the Lagrange interpolating polynomial for this new data, then we need to compute all the Lagrange fundamental polynomials again. The nth degree Lagrange polynomial obtained earlier is of no, use., 7. Does the Newton’s divided difference interpolating polynomial have the permanence, property?, Solution Newton’s divided difference interpolating polynomial has the permanence, property. Suppose that to the given data (xi, f(xi)), i = 0, 1, 2,…, n, a new data value (xn+1,, f(xn+1)) at the distinct point xn+1 is added at the end of the table. Then, the (n + 1) th, column of the divided difference table has the (n + 1)th divided difference. Hence, the, data represents a polynomial of degree (n + 1). We need to add only one extra term, (x – x0)(x – x1)...(x – xn) f[x0, x1, ... xn + 1] to the previously obtained nth degree divided, difference polynomial., 8. Define inverse interpolation., Solution Suppose that a data (xi, f(xi)), i = 0, 1, 2,…, n, is given. In interpolation, we, predict the value of the ordinate f(x′) at a non-tabular point x = x′. In many applications,, we require the value of the abscissa x′ for a given value of the ordinate f(x′). For this, problem, we consider the given data as ( f (xi), xi), i = 0, 1, 2,…, n and construct the, interpolation polynomial. That is, we consider f(x) as the independent variable and x as, the dependent variable. This procedure is called inverse interpolation, , EXERCISE 2.1, 1. Use the Lagrange’s formula to find the quadratic polynomial that takes these values, , Then, find f(2)., , x, , 0, , 1, , 3, , y, , 0, , 1, , 0, , (A.U Nov/Dec. 2005)
Page 89 :
78, , NUMERICAL METHODS, , 2. Using Lagrange interpolation, find the unique polynomial P(x) of degree 2 or less such, that P(1) = 1, P(3) = 27, P(4) = 64., 3. A third degree polynomial passes through the points (0, – 1), (1, 1), (2, 1), and (3, 2)., Determine this polynomial using Lagrange’s interpolation. Hence, find the value at 1.5., 4. Using Lagrange interpolation, find y(10) given that, y(5) = 12, y(6) = 13, y(9) = 14, y(11) = 16., 5. Find the polynomial f(x) by using Lagrange’s formula and hence find f(3) for, x, , 0, , 1, , 2, , 5, , f(x), , 2, , 3, , 12, , 147, , (A.U Apr/May 2005), 6. Using Lagrange’s method, fit a polynomial to the data, x, , 0, , 1, , 2, , 4, , y, , – 12, , 0, , 6, , 12, , Also find y at x = 2., , (A.U Nov/Dec. 2006), , 7. Using Lagrange interpolation, calculate the profit in the year 2000 from the following, data., Year, Profit in lakhs of Rs., , 1997, , 1999, , 2001, , 2002, , 43, , 65, , 159, , 248, , (A.U Nov/Dec. 2004), 8. Given the values, x, , 14, , 17, , 31, , 35, , f(x), , 68.7, , 64.0, , 44.0, , 39.1, , find f(27) by using Lagrange’s interpolation formula., (A.U May/Jun 2006, Nov/Dec. 2006), 9. From the given values, evaluate f(9) using Lagrange’s formula., x, f(x), , 5, , 7, , 11, , 13, , 17, , 150, , 392, , 1452, , 2366, , 5202, , (A.U Nov/Dec. 2003), 10. From the given values, evaluate f(3) using Lagrange’s formula., x, , –1, , 2, , 4, , 5, , f(x), , –5, , 13, , 255, , 625
Page 90 :
79, , INTERPOLATION AND APPROXIMATION, , 11. Find the missing term in the table using Lagrange’s interpolation, , 12., , x, , 0, , 1, , 2, , 3, , 4, , y, , 1, , 3, , 9, , –, , 81, , Obtain the root of f(x) = 0 by Lagrange’s interpolation given that, f(30) = – 30, f(34) = – 13, f(38) = 3, f(42) = 18., , (A.U Nov/Dec. 2004), , 13. Using the Lagrange interpolation with the truncation error, show that the Lagrange, interpolation polynomial for f(x) = xn+1 at the points x0, x1, …, xn is given by xn+1 – (x –, x0)(x – x1)...(x – xn)., 14. Show that, , 3, , ∆, , abcd, , FG 1 IJ = − 1, H a K abcd, , (A.U Nov/Dec. 2004), , 15. If f(x) = 1/x2, find the divided difference f [x1, x2, x3, x4]., 16. Calculate the nth divided difference of 1/x, based on the points x0, x1, x2,..., xn, 17. Using Newton’s divided difference formula, determine f(3) for the data, x, , 0, , 1, , 2, , 4, , 5, , f(x), , 1, , 14, , 15, , 5, , 6, , 18. Using Newton’s divided difference interpolation, find y(10) given that, y(5) = 12, y(6) = 13, y(9) = 14, y(11) = 16., 19. Using divided difference formula, find u(3) given, u(1) = – 26, u(2) = 12, u(4) = 256, and u(6) = 844., , (A.U Nov/Dec. 2004), , 20. Find f(8) by Newton’s divided difference formula, for the data, x, , 4, , 5, , 7, , 10, , 11, , 13, , f(x), , 48, , 100, , 294, , 900, , 1210, , 2028, , (A.U Apr/May 2005), 21. Using Newton’s divided difference method, find f(1.5) using the data, f(1.0) = 0.7651977, f(1.3) = 0.6200860, f(1.6) = 0.4554022,, f(1.9) = 0.2818186, and f(2.2) = 0.1103623., , (A.U Nov/Dec. 2005), , 22. From the given values, evaluate f(3) using Newton’s divided difference formula., x, , –1, , 2, , 4, , 5, , f(x), , –5, , 13, , 255, , 625
Page 91 :
80, 2.3, , NUMERICAL METHODS, , INTERPOLATION WITH EVENLY SPACED POINTS, , Let the data (xi, f(xi)) be given with uniform spacing, that is, the nodal points are given by, xi = x0 + ih, i = 0, 1, 2, ..., n. In this case, Lagrange and divided difference interpolation, polynomials can also be used for interpolation. However, we can derive simpler interpolation, formulas for the uniform mesh case. We define finite difference operators and finite differences, to derive these formulas., Finite difference operators and finite differences, We define the following five difference operators., Shift operator E When the operator E is applied on f(xi ), we obtain, Ef(xi) = f(xi + h) = f(xi+1)., That is,, , (2.17), , Ef(x0) = f(x0 + h) = f(x1), Ef(x1) = f(x1 + h) = f(x2), etc., , Therefore, the operator E when applied on f(x) shifts it to the value at the next nodal point. We, have, E2 f(xi) = E[Ef(xi)] = E[f(xi + h)] = f(xi + 2h) = f(xi+2)., In general, we have, Ek f(xi) = f(xi + kh) = f(xi+k), , (2.18), , where k is any real number. For example, we define, , FG, H, , E 1/ 2 f ( xi ) = f xi +, , IJ, K, , h, = f ( xi + 1/ 2 ) ., 2, , Forward difference operator ∆ When the operator ∆ is applied on f(xi), we obtain, ∆ f(xi) = f(xi + h) – f(xi) = fi+1 – fi ., That is,, , ∆ f(x0) = f(x0 + h) – f(x0) = f(x1) – f(x0),, ∆ f(x1) = f(x1 + h) – f(x1) = f(x2) – f(x1), etc., , These differences are called the first forward differences., The second forward difference is defined by, ∆2 f(xi) = ∆[∆ f(xi)] = ∆[f(xi + h) – f(xi)] = ∆ f(xi + h) – ∆ f(xi), = [f(xi + 2h) – f(xi + h)] – [f(xi + h) – f(xi)], = f(xi + 2h) – 2f(xi + h) + f(xi) = fi+2 – 2fi+1 + fi., The third forward difference is defined by, ∆3 f(xi) = ∆[∆2 f(xi)] = ∆ f(xi + 2h) – 2∆ f(xi + h) + ∆ f(xi), = fi+3 – 3fi+2 + 3fi+1 – fi., Now, from (2.18) and (2.19), we get, ∆ f(xi) = f(xi + h) – f(xi) = E fi – fi = (E – 1) fi., , (2.19)
Page 92 :
81, , INTERPOLATION AND APPROXIMATION, , Comparing, we obtain the operator relation, ∆ = E – 1, or E = 1 + ∆., , (2.20), , Using this relation, we can write the nth forward difference of f(xi) as, n, , ∆n f(xi) = (E – 1)n f(xi) =, , ∑, , ( − 1) k, , k=0, , n!, fi +n − k ., k ! (n − k ) !, , (2.21), , The forward differences can be written in a tabular form as in Table 2.2., Table 2.2. Forward differences., x, , f(x), , x0, , f(x0), , ∆2 f, , ∆f, , ∆3 f, , ∆f0 = f1 – f0, x1, , ∆2 f0 = ∆f1 – ∆f0, , f(x1), , ∆3f0 = ∆2f1 – ∆2f0, , ∆f1 = f2 – f1, x2, , ∆2f, , f(x2), , 1, , = ∆f2 – ∆f1, , ∆f2 = f3 – f2, x3, , f(x3), , Backward difference operator ∇ When the operator ∇ is applied on f(xi), we obtain, ∇ f(xi) = f(xi) – f(xi – h) = fi – fi–1., That is,, , (2.22), , ∇ f(x1) = f(x1) – f(x0),, ∇ f(x2) = f(x2) – f(x1), etc., , These differences are called the first backward differences., The second backward difference is defined by, ∇2 f(xi) = ∇[∇ f(xi)] = ∇[f(xi) – f(xi – h)] = ∇ f(xi) – ∇ f(xi – h), = f(xi) – f(xi – h)] – [f(xi – h) – f(xi – 2h)], = f(xi) – 2f(xi – h) + f(xi – 2h) = fi – 2fi–1 + fi–2, The third backward difference is defined by, ∇3 f(xi) = ∇[∇2 f(xi)] = ∇ f(xi) – 2∇ f(xi – h) + ∇ f(xi – 2h), = fi – 3fi–1 + 3fi–2 – fi–3., Now, from (2.18) and (2.22), we get, ∇ f(xi) = f(xi) – f(xi – h) = fi – E–1 fi = (1 – E–1)fi., Comparing, we obtain the operator relation, ∇ = 1 – E–1, or E–1 = 1 – ∇, or E = (1 – ∇)–1., , (2.23)
Page 93 :
82, , NUMERICAL METHODS, , Using this relation, we can write the nth backward difference of f(xi) as, n, , ∇n, , f(xi) = (1 –, , E–1)n, , f(xi) =, , ∑, , (− 1) k, , k=0, , n!, fi − k, k ! (n − k) !, , (2.24), , The backward differences can be written in a tabular form as in Table 2.3., Table 2.3. Backward differences., x, , f(x), , x0, , f(x0), , ∇2 f, , ∇f, , ∇3 f, , ∇f1 = f1 – f0, x1, , ∇2f2 = ∇ f2 – ∇ f1, , f(x1), , ∇3f3 = ∇2 f3 – ∇2 f2, , ∇f2 = f2 – f1, x2, , ∇2 f3 = ∇ f3 – ∇ f2, , f(x2), ∇f3 = f3 – f2, , x3, , f(x3), , Remark 6 From the difference tables 2.2, 2.3, we note that the numbers (values of differences) in all the columns in the two tables are same. We identify these numbers as the required forward or backward difference. For example, from the columns of the table, we have, ∆ f0 = ∇f1, ∆ f1 = ∇f2, ∆f2 = ∇f3, ..., ∆3f0 = ∇3f3., Example 2.11 Construct the forward difference table for the data, x, , –1, , 0, , 1, , 2, , f(x), , –8, , 3, , 1, , 12, , Solution We have the following difference table., Forward difference table. Example 2.11, x, , f(x), , –1, , –8, , ∆f, , ∆2 f, , ∆3 f, , 3 + 8 = 11, 0, , 3, , – 2 – 11 = –13, 1–3=–2, , 1, , 1, , 11 + 2 = 13, 12 – 1 = 11, , 2, , 12, , 13 + 13 = 26
Page 96 :
85, , INTERPOLATION AND APPROXIMATION, , Table 2.5. Central differences., x, , f(x), , x–2, , f–2, , δ2f, , δf, , δ3f, , δ4f, , δf–3/2, x–1, , δ2 f–1, , f–1, , δ3f–1/2, , δf–1/2, x0, , δ2 f0, , f0, , δ4f0, δ3f1/2, , δ f1/2, x1, , δ2 f1, , f1, δ f3/2, , x2, , f2, , Remark 9 For well behaved functions, the forward differences, backward differences and, central differences decrease in magnitude along each column. That is, the second difference is, smaller in magnitude than the first difference, the third difference is smaller in magnitude, than second difference etc., Mean operator µ When the operator µ is applied on f(xi), we obtain, µ f(xi) =, , LM FG, NH, , IJ FG, K H, , 1, h, h, + f xi −, f xi +, 2, 2, 2, , IJ OP = 1 f, KQ 2, , i +1/ 2, , + f i −1/ 2 =, , 1 1/ 2, E + E −1/ 2 fi, 2, , Comparing, we have the operator relation, , 1 1/ 2, E + E −1/ 2 ., 2, Example 2.13 Compute ∆3(1 – 2x)(1 – 3x)(1 – 4x)., µ=, , (2.29), , Solution We have, ∆3(1 – 2x)(1 – 3x)(1 – 4x) = ∆3(– 24x3 + lower order terms), = – 24 (3 !) = – 144, since ∆3 (polynomial of degree 2 and less) = 0., Example 2.14 Construct the forward difference table for the sequence of values, f(0, 0, 0, ε, 0, 0, 0), where ε is the magnitude of the error in one ordinate value and all other ordinates are exact., Show that the errors propagate and increase in magnitude and that the errors in each column, are binomial coefficients., Solution We have the following difference table. From the table, it can be observed that the, errors propagate and increase in magnitude and that the errors in each column are binomial, coefficients.
Page 98 :
87, , INTERPOLATION AND APPROXIMATION, , =, , g( x)[ f ( x + h) − f ( x)] − f ( x)[ g ( x + h) − g( x)], g ( x) g ( x + h), , =, , g( x)∆f ( x) − f ( x) ∆g ( x), ., g( x) g( x + h), , Relations between differences and derivatives, We write Ef(x) as, Ef(x) = f(x + h) = f(x) + hf ′(x) +, , LM, N, , = 1 + hD +, , h2, f ″(x) + ..., 2, , OP, Q, , h2 D2, + ... f(x) = ehD f(x)., 2!, , D r f(x) = dr f / dxr, r = 1, 2, ..., , where, , Hence, we obtain the operator relation, E = ehD or hD = ln(E)., , (2.30), , In terms of the forward, backward and central differences, we obtain, , hD = ln( E) = ln(1 + ∆ ) = ∆ −, , 1 2 1 3, ∆ + ∆ − ..., 2, 3, , hD = ln( E ) = ln(1 − ∇ ) −1 = − ln(1 − ∇ ) = ∇ +, , Also,, Hence,, , (2.31), 1 2 1 3, ∇ + ∇ + ..., 2, 3, , (2.32), , δ = E1/2 – E–1/2 = ehD/2 – e–hD/2 = 2 sinh (hD/2)., , (2.33), , hD = 2 sinh–1 (δ/2) and h2D2 = 4 [sinh–1 (δ/2)]2., , (2.34), , Using the Taylor series expansions, we get, ∆ f(x) = f(x + h) – f(x), , LM, N, , = f ( x) + hf ′ ( x) +, , OP, Q, , h2, h2, f ′′( x) + ... − f ( x) = hf ′( x) +, f ′′ ( x) + ..., 2, 2, , Neglecting the higher order terms, we get the approximation, ∆ f(x) ≈ hf ′(x),, , or f ′(x) ≈, , 1, ∆ f(x)., h, , (2.35), , The error term is given by, , f ′( x) −, , 1, h, ∆ f ( x) = − f ′′ ( x) + ..., h, 2, , Hence, we call the approximation given in (2.35) as a first order approximation or of order, O(h).
Page 99 :
88, , NUMERICAL METHODS, , ∆2 f(x) = f(x + 2h) – 2f(x + h) + f(x), , We have, , LM, N, , = f ( x) + 2 hf ′ ( x) +, , OP, Q, O, f ′′′( x) + ...P + f(x), Q, , 4h2, 8h 3, f ′′( x) +, f ′′′( x) + ..., 2, 6, , LM, N, , h2, h3, f ′′( x) +, 2, 6, , – 2 f ( x) + hf ′ ( x) +, , = h2 f ″(x) + h3 f ′″(x) + ..., Neglecting the higher order terms, we get the approximation, ∆2f(x) ≈ h2 f ″(x), or, , 1, , f ″(x) ≈, , h2, , ∆2 f(x)., , (2.36), , The error term is given by, f ′′ ( x) −, , 1, h2, , ∆2 f ( x) = − h f ′′′( x) + ..., , Hence, we call the approximation given in (2.36) as a first order approximation or of, order O(h)., Similarly, we have the following results for backward differences., ∇ f(x) ≈ hf ′(x), or, , f ′ ( x) ≈, , ∇2 f(x) ≈ h2f ′′(x), or f ′′( x ) ≈, For the central differences, we obtain, , FG, H, , δ f ( x) = f x +, , LM, N, , 1, ∇ f ( x), h, 1, h2, , IJ FG, K H, , ∇ 2 f ( x ) . [O(h) approximation], , h, h, − f x−, 2, 2, , = f ( x) +, , [O(h) approximation], , IJ, K, , OP, Q, , (2.37), (2.38), , h, h2, h3, f ′ ( x) +, f ′′ ( x) +, f ′′′( x) + ..., 2, 8, 48, , LM, N, , – f ( x) −, , = hf ′(x) +, , OP, Q, , h, h2, h3, f ′( x) +, f ′′ ( x) −, f ′′′( x) + ..., 2, 8, 48, , h3, f ′′′( x) + ..., 24, , Neglecting the higher order terms, we get the approximation, δ f(x) ≈ h f ′(x),, , or f ′(x) ≈, , The error term is given by, f ′( x) −, , 1, h2, δ f ( x) = −, f ′′′( x) + ..., h, 24, , 1, δ f(x)., h, , (2.39)
Page 100 :
89, , INTERPOLATION AND APPROXIMATION, , Hence, we call the approximation given in (2.39) as a second order approximation or of, order O(h2)., We have δ2 f(x) = f(x + h) – 2f(x) + f(x – h), , LM, N, , = f ( x) + hf ′( x) +, , OP, Q, , LM, N, , OP, Q, , h2, h2, f ′′ ( x) + ... – 2 f(x) + f ( x) − hf ′( x) +, f ′′ ( x) − ..., 2, 2, , Neglecting the higher order terms, we get the approximation, δ2 f(x) ≈ h2 f ″(x),, , or f ″ (x) ≈, , 1, h2, , δ2 f(x)., , (2.40), , The error term is given by, f ″(x) –, , 1, h, , 2, , δ2 f(x) = –, , h 2 ( iv), f, ( x) + ..., 12, , Hence, we call the approximation given in (2.35) as a second order approximation or of, order O(h2)., Note that the central differences give approximations of higher order because of symmetry of the arguments., The divided differences are also related to forward differences and backward differences., In the uniform mesh case, the divided differences can be written as, f [ xi , xi + 1 ] =, f [ xi , xi + 1 , xi + 2 ] =, , =, , f ( xi + 1 ) − f ( xi ) 1, 1, = ∆ fi = ∇ fi + 1 ., xi +1 − xi, h, h, f [ xi + 1 , xi + 2 ] − f [ xi , xi + 1 ] (1/h) ∆fi + 1 − (1/h) ∆fi, =, 2h, xi + 2 − xi, 1, 2! h, , 2, , ∆2 fi =, , 1, 2 ! h2, , ∇ 2 fi + 2 ., , By induction we can prove that the nth divided difference can be written as, f [ x0 , x1 , ..., x n ] =, , 1, n! h, , n, , ∆n f0 =, , 1, n !h, , n, , ∇ n fn ., , 2.3.1 Newton’s Forward Difference Interpolation Formula, Let h be the step length in the given data., In terms of the divided differences, we have the interpolation formula as, f(x) = f (x0) + (x – x0) f [x0, x1] + (x – x0)(x – x1) f [x0, x1, x2] + ..., Using the relations for the divided differences given in (2.36), f [ x0 , x1 , ..., xn ] =, , 1, n ! hn, , ∆n f0, , (2.41)
Page 101 :
90, , we get, , NUMERICAL METHODS, , f(x) = f(x0) + (x – x0), , ∆2 f0, ∆f0, (x – x0)(x – x1), + ..., 1! h, 2 ! h2, , + (x – x0)(x – x1)...(x – xn–1), , ∆n f0, , 1! h n, , (2.42), , This relation is called the Newton’s forward difference interpolation formula., Suppose that we want to interpolate near the point x0 . Set x = x0 + sh. Then,, x – xi = x0 + sh – (x0 + ih) = (s – i)h., Therefore,, , x – x0 = sh, x – x1 = (s – 1)h, x – x2 = (s – 2)h, etc., , Substituting in (2.42), we obtain, f(x) = f(x0 + sh), = f(x0) + s∆f0 +, , s(s − 1) 2, s(s − 1)(s − 2) ... (s − n + 1) n, ∆ f0 + ... +, ∆ f0, n!, 2!, , We note that the coefficients are the binomial coefficients, , (2.43), , sC 0 , sC1 ,..., sC n ., , Hence, we can write the formula (2.43) as, f(x) = f(x0 + sh), = sC0 f(x0) + sC1 ∆f0 + sC2 ∆2f0 + ... + sCn ∆nf0, Note that, , s = [(x – x0)/h] > 0., , This is an alternate form of the Newton’s forward difference interpolation formula., Error of interpolation The error of interpolation is same as in the Lagrange interpolation., Therefore, error of interpolation is given by, En(f, x) =, =, , ( x − x0 )( x − x1 )...( x − xn ) ( n + 1), (ξ), f, (n + 1) !, , s( s − 1)( s − 2)..( s − n ) n +1 ( n +1), h, f, ( ξ ) = sCn +1 h n +1 f ( n +1) ( ξ ), (n + 1) !, , (2.44), , where 0 < ξ < n. The coefficient in the error expression is the next binomial coefficient sCn+1., Remark 10 The Newton’s forward difference formula has the permanence property. Suppose, we add a new data value (xn+1, f(xn+1)) at the end of the given table of values. Then, the, (n + 1)th column of the forward difference table has the (n + 1)th forward difference. Then, the, Newton’s forward difference formula becomes, f(x) = f(x0) + (x – x0), , ∆f0, ∆2 f0, + ( x − x0 )( x − x1 ), + ..., 1! h, 2 ! h2, , + (x – x0)(x – x1)...(x – xn), , ∆n +1 f0, (n + 1) ! h n + 1
Page 102 :
91, , INTERPOLATION AND APPROXIMATION, , Example 2.16 Derive the Newton’s forward difference formula using the operator relations., Solution We have, f(x0 + sh) = Es f(x0) = (1 + ∆)s f(x0)., Symbolically, expanding the right hand side, we obtain, f(x0 + sh) = (sC0 + sC1∆ + sC2∆2 + ...) f(x0), = sC0 f(x0) + sC1∆f(x0) + sC2∆2 f(x0) + ... + sCn∆n f(x0) + ..., We neglect the (n + 1)th and higher order differences to obtain the Newton’s forward, difference formula as, f(x0 + sh) = (sC0 + sC1∆ + sC2∆2 + ...) f(x0), = sC0 f(x0) + sC1∆f(x0) + sC2∆2f(x0) + ... + sCn∆n f(x0)., Example 2.17 For the data, x, , –2, , –1, , 0, , 1, , 2, , 3, , f (x), , 15, , 5, , 1, , 3, , 11, , 25, , construct the forward difference formula. Hence, find f (0.5)., Solution We have the following forward difference table., Forward difference table. Example 2.17., x, , f(x), , –2, , 15, , ∇2 f, , ∇f, , ∇3 f, , – 10, –1, , 5, , 6, –4, , 0, , 1, , 1, , 3, , 0, 6, , 2, , 0, 6, , 8, 2, , 0, , 11, , 6, 14, , 3, , 25, , From the table, we conclude that the data represents a quadratic polynomial. We have, h = 1. The Newton’s forward difference formula is given by, f(x) = f(x0) + (x – x0), , FG ∆f IJ + (x − x )(x − x ) FG ∆ f IJ, HhK, H 2h K, 0, , 2, , 0, , 1, , 0, 2
Page 104 :
93, , INTERPOLATION AND APPROXIMATION, , Note that s = [(x – xn)/h] < 0. The magnitudes of the successive terms on the right hand, side become smaller and smaller. Note that the coefficients are the binomial coefficients, [(– 1)k (– s)Ck]., Error of interpolation The expression for the error becomes, En(f, x) =, , ( x − xn )( x − x n − 1 ) ... ( x − x0 ) ( n +1), (ξ), f, (n + 1) !, , =, , s(s + 1)(s + 2) ... (s + n) n +1 (n+ 1), h, f, (ξ), (n + 1) !, , (2.48), , where 0 < ξ < n., Remark 11 As in divided differences, given a table of values, we can determine the degree of, the forward/ backward difference polynomial using the difference table. The kth column of the, difference table contains the kth forward/ backward differences. If the values of these differences are same, then the (k + 1)th and higher order differences are zero. Hence, the given data, represents a kth degree polynomial., Remark 12 We use the forward difference interpolation when we want to interpolate near, the top of the table and backward difference interpolation when we want to interpolate near, the bottom of the table., Example 2.18 Derive the Newton’s backward difference formula using the operator relations., Solution Let, , x = xn + sh. Then, s = [(x – xn)/h] < 0, f(xn + sh) = Es f(xn) = (1 – ∇)–s f(xn), , We have, , Symbolically, expanding the right hand side, we obtain, f(xn + sh) = f(xn) + s∇f(xn) +, , s(s + 1) ... (s + n − 1) n, s( s + 1) 2, ∇ f(xn) + ... +, ∇ f(xn) + ..., 2!, n!, , We neglect the (n + 1)th and higher order differences to obtain the Newton’s backward, difference formula as, f(xn + sh) = f(xn) + s∇f(xn) +, , s(s + 1) ... (s + n − 1) n, s( s + 1) 2, ∇ f(xn) + ... +, ∇ f(xn)., 2!, n!, , Example 2.19 For the following data, calculate the differences and obtain the Newton’s, forward and backward difference interpolation polynomials. Are these polynomials different?, Interpolate at x = 0.25 and x = 0.35., x, , 0.1, , 0.2, , 0.3, , 0.4, , 0.5, , f(x), , 1.40, , 1.56, , 1.76, , 2.00, , 2.28, , Solution The step length is h = 0.1. We have the following difference table., Since, the third and higher order differences are zero, the data represents a quadratic, polynomial. The third column represents the first forward/ backward differences and the fourth, column represents the second forward/ backward differences.
Page 105 :
94, , NUMERICAL METHODS, , The forward difference polynomial is given by, f(x) = f(x0) + (x – x0), = 1.4 + (x – 0.1), , ∆2 f0, ∆f0, + (x – x0) (x – x1), h, 2 ! h2, , FG 0.16 IJ + (x − 0.1)(x − 0.2) FG 0.04 IJ, H 0.1 K, H 0.02 K, , = 2x2 + x + 1.28., The backward difference polynomial is given by, f(x) = f(xn) + (x – xn), , ∇ fn, ∇ 2 fn, + ( x − xn )( x − xn −1 ), h, 2 ! h2, , = 2.28 + (x – 0.5), , FG 0.28 IJ + ( x − 0.5)( x − 0.4) FG 0.04 IJ, H 0.1 K, H 0.02 K, , = 2x2 + x + 1.28., Both the polynomials are identical, since the interpolation polynomial is unique. We obtain, f(0.25) = 2(0.25)2 + 0.25 + 1.28 = 1.655, f(0.35) = 2(0.35)2 + (0.35) + 1.28 = 1.875., Difference table. Example 2.19., x, , f(x), , 0.1, , 1.40, , ∇2 f, , ∇f, , ∇3 f, , ∇4 f, , 0.16, 0.2, , 1.56, , 0.3, , 1.76, , 0.04, 0.20, , 0.0, 0.04, , 0.0, , 0.24, 0.4, , 0.0, , 2.00, , 0.04, 0.28, , 0.5, , 2.28, , Example 2.20 Using Newton’s backward difference interpolation, interpolate at x = 1.0 from, the following data., x, , 0.1, , 0.3, , 0.5, , 0.7, , 0.9, , 1.1, , f(x), , – 1.699, , – 1.073, , – 0.375, , 0.443, , 1.429, , 2.631, , Solution The step length is h = 0.2. We have the difference table as given below.
Page 106 :
95, , INTERPOLATION AND APPROXIMATION, , Since the fourth and higher order differences are zero, the data represents a third degree polynomial. The Newton’s backward difference interpolation polynomial is given by, f(x) = f(xn) + (x – xn), , 1, 1, ∇ f(xn) + (x – xn)(x – xn–1), ∇2 f(xn), 1! h, 2 ! h2, , + (x – xn)(x – xn–1)(x – xn–2), = 2.631 + (x – 1.1), , 1, 3!h, , 3, , ∇3 f ( x n ), , FG 1.202IJ + (x – 1.1)(x – 0.9) FG 0.216 IJ, H 2(0.04) K, H 0.2 K, , + (x – 1.1)(x – 0.9)(x – 0.7), , FG 0.048 IJ, H 6( 0.008) K, , = 2.631 + 6.01(x – 1.1) + 2.7(x – 1.1)(x – 0.9) + (x – 1.1)(x – 0.9)(x – 0.7), Since, we have not been asked to find the interpolation polynomial, we may not simplify this expression. At x = 1.0, we obtain, f(1.0) = 2.631 + 6.01(1.0 – 1.1) + 2.7(1.0 – 1.1)(1.0 – 0.9) + (1.0 – 1.1)(1.0 – 0.9)(1.0 – 0.7), = 2.631 + 6.01(– 0.1) + 2.7(– 0.1)(0.1) + (– 0.1)(0.1)(– 0.3) = 2.004., Difference table. Example 2.20., x, , f(x), , 0.1, , – 1.699, , 0.3, , – 1.073, , ∇f, , ∇2 f, , ∇3 f, , ∇4 f, , ∇5 f, , 0.626, 0.072, 0.698, 0.5, , – 0.375, , 0.048, 0.120, , 0.818, 0.7, , 0.443, , 0.9, , 1.429, , 0.0, 0.048, , 0.168, 0.986, , 0.0, 0.0, , 0.048, 0.216, , 1.202, 1.1, , 2.631, , REVIEW QUESTIONS, 1. Write the expression for the derivative operator D in terms of the forward difference, operator ∆., Solution The required expression is, hD = ln(E) = ln(1 + ∆) = ∆ –, , 1 2 1 3, ∆ + ∆ – ..., 2, 3
Page 107 :
96, , NUMERICAL METHODS, , or, , D=, , LM∆ − 1 ∆, N 2, , 1, 1, 1, ln(E) = ln (1 + ∆) =, h, h, h, , 2, , +, , OP, Q, , 1 3, ∆ − ..., 3, , 2. Write the expression for the derivative operator D in terms of the backward difference, operator ∇., Solution The required expression is, hD = ln(E) = ln(1 – ∇)–1 = – ln(1 – ∇) = ∇ +, or, , D=, , 1 2 1 3, ∇ + ∇ + ..., 2, 3, , LM, N, , OP, Q, , 1, 1, 1, 1, 1, 1, ∇ + ∇ 2 + ∇ 3 + ... ., ln(E) = ln (1 – ∇)–1 = –, ln(1 – ∇) =, h, h, h, h, 2, 3, , 3. What is the order of the approximation f ′(x) ≈, Solution The error term is given by f ′(x) –, , 1, ∆ f(x) ?, h, , 1, h, ∆ f(x) = – f ′′( x) + ..., h, 2, , Hence, it is a first order approximation or of order O(h)., 4. What is the order of the approximation f ′′ ( x) ≈, Solution The error term is given by, , f ′′( x) −, , 1, h2, , ∆2 f ( x) ?, , 1 2, ∆ f ( x) = − h f ′′′( x) + ..., h2, , Hence, it is a first order approximation or of order O(h)., 5. What is the order of the approximation f ′′ ( x) ≈, , 1, h2, , δ 2 f ( x) ?, , 2, Solution The error term is given by f ′′ ( x) − 12 δ 2 f ( x) = − h f (iv) ( x) + ..., , h, , 12, , Hence, it is a second order approximation or of order O(h2)., 6. Give the relation between the divided differences and forward or backward differences., Solution The required relation is, f [x0, x1, ..., xn] =, , 1, 1, ∆n f0 =, ∇ n fn ., n ! hn, n ! hn, , 7. Does the Newton’s forward difference formula has permanence property ?, Solution Yes. The Newton’s forward difference formula has permanence property., Suppose we add a new data value (xn+1, f(xn+1)) at the end of the given table of values., Then, the (n + 1)th column of the forward difference table has the (n + 1)th forward, difference. Then, the Newton’s forward difference formula becomes
Page 108 :
97, , INTERPOLATION AND APPROXIMATION, , f(x) = f(x0) + (x – x0), , ∆f0, ∆2 f0, + ..., + ( x − x0 )( x − x1), 1! h, 2 ! h2, , + (x – x0)(x – x1) ... (x – xn), , ∆n + 1 f0, (n + 1) ! h n + 1, , 8. For performing interpolation for a given data, when do we use the Newton’s forward, and backward difference formulas?, Solution We use the forward difference interpolation when we want to interpolate, near the top of the table and backward difference interpolation when we want to, interpolate near the bottom of the table., 9. Can we decide the degree of the polynomial that a data represents by writing the forward, or backward difference tables?, Solution Given a table of values, we can determine the degree of the forward/ backward, difference polynomial using the difference table. The kth column of the difference table, contains the kth forward/ backward differences. If the values of these differences are, same, then the (k + 1)th and higher order differences are zero. Hence, the given data, represents a kth degree polynomial., 10. If x = x0 + sh, write the error expression in the Newton’s forward difference formula., Solution The error expression is given by, En(f, x) =, , s(s − 1)(s − 2)..(s − n) n + 1 ( n +1), h, f, (ξ) = sCn + 1h n + 1 f ( n + 1) (ξ). 0 < ξ < n ., (n + 1) !, , 11. If x = xn + sh, write the error expression in the Newton’s backward difference formula., Solution The error expression is given by, En(f, x) =, , s(s + 1)(s + 2)..(s + n) n+ 1 (n +1), h, f, (ξ)., (n + 1) !, , 0 < ξ < n., , EXERCISE 2.2, 1. Prove the following., (i) ∆, , F 1 I = − ∆f, GH f JK f f, , i, , ., , i i+ 1, , i, , (iv) ∆ – ∇ = – ∆ ∇., , (ii) ∆ + ∇ =, , n, , ∆ ∇, − ., ∇ ∆, , (iii), , ∑, , k=0, , ∆2 f k = ∆f n + 1 − ∆f0 ., , (v) µδ = (∆ + ∇)/2., , (iv) (1 + ∆)(1 – ∇) = 1., , (vii) δ = ∇E1/2., , (viii), , 1 + δ 2 µ 2 = 1 + (1/2) δ2., , 2. Using the Newton’s forward difference formula, find the polynomial f(x) satisfying the, following data. Hence, evaluate y at x = 5., x, , 4, , 6, , 8, , 10, , y, , 1, , 3, , 8, , 10, , (A.U. May/Jun 2006)
Page 109 :
98, , NUMERICAL METHODS, , 3. A third degree polynomial passes through the points (0, – 1), (1, 1), (2, 1) and (3, – 2)., Determine this polynomial using Newton’s forward interpolation formula. Hence, find, the value at 1.5., 4. Using the Newton’s forward interpolation formula, find the cubic polynomial which, takes the following values., x, , 0, , 1, , 2, , 3, , y, , 1, , 2, , 1, , 10, , Evaluate y(4) using Newton’s backward interpolation formula. Is it the same as obtained from the cubic polynomial found above?, 5. Obtain the interpolating quadratic polynomial for the given data by using the Newton’s, forward difference formula, x, , 0, , 2, , 4, , 6, , y, , –3, , 5, , 21, , 45, , (A.U. Nov/Dec 2003), 6. For the following data, estimate the number of persons earning weekly wages between, 60 and 70 rupees., Wage (in Rs.), , below 40, , 40–60, , 60–80, , 80–100, , 100–120, , No. of persons, (in thousands), , 250, , 120, , 100, , 70, , 50, , (A.U. Nov/Dec 2003), 7. Using the Newton’s backward interpolation formula construct an interpolation polynomial of degree 3 for the data, f(– 0.75) = – 0.07181250, f(– 0.5) = – 0.024750, f(– 0.25) = 0.33493750, f(0) = 1.1010., Hence, find f(– 1/3)., , (A.U. Apr/May 2003), , 8. Using the Newton’s forward difference formula, find the polynomial f(x) satisfying the, following data. Hence, find f(2)., x, , 0, , 5, , 10, , 15, , y, , 14, , 379, , 1444, , 3584, , (A.U. Apr/May 2004), 9. The following data represents the function f(x) =, , e x., , x, , 1, , 1.5, , 2.0, , 2.5, , y, , 2.7183, , 4.4817, , 7.3891, , 12.1825
Page 110 :
99, , INTERPOLATION AND APPROXIMATION, , Estimate the value of f(2.25) using the (i) Newton’s forward difference interpolation, and (ii) Newton’s backward difference interpolation. Compare with the exact value., 10. The following data represents the function f(x) = cos (x + 1)., x, , 0.0, , 0.2, , 0.4, , 0.6, , f(x), , 0.5403, , 0.3624, , 0.1700, , – 0.0292, , Estimate the value of f(0.5) using the Newton’s backward difference interpolation. Compare with the exact value., 11. The following data are part of a table for f ( x) = cos x / x , where x is in radians., x, , 0.1, , 0.2, , 0.3, , 0.4, , f(x), , 9.9500, , 4.9003, , 3.1845, , 2.3027, , Calculate f(0.12), (i) by interpolating directly from the table, (ii) by first tabulating x, f(x) and then interpolating from the table. Explain the difference between the results., , 2.4, , SPLINE INTERPOLATION AND CUBIC SPLINES, , In the earlier days of development of engineering devices, the draftsman used a device to, draw smooth curves through a given sets of points such that the slope and curvature are also, continuous along the curves, that is, f(x), f′(x) and f″(x) are continuous on the curves. Such a, device was called a spline and plotting of the curve was called spline fitting., We now define a spline., Let the given interval [a, b] be subdivided into n subintervals [x0, x1], [x1, x2], ...,, [xn–1, xn] where a = x0 < x1 < x2 < ... < xn = b. The points x0, x1, ..., xn are called nodes or knots and, x1, ..., xn–1 are called internal nodes., Spline function A spline function of degree n with nodes x0, x1, ..., xn, is a function F(x), satisfying the following properties., (i) F(xi) = f(xi), i = 0, 1, ...., n. (Interpolation conditions)., (ii) On each subinterval [xi–1, xi], 1 ≤ i ≤ n, F(x) is a polynomial of degree n., (iii) F(x) and its first (n – 1) derivatives are continuous on (a, b)., For our discussion, we shall consider cubic splines only. From the definition, a cubic spline, has the following properties., (i) F(xi) = f(xi), i = 0, 1, ..., n. (Interpolation conditions)., (ii) On each subinterval [xi–1, xi], 1 ≤ i ≤ n, F(x) is a third degree (cubic) polynomial., (iii) F(x), F′(x) and F ″(x) are continuous on (a, b)., Let, , F(x) = Pi(x) = aix3 + bix2 + cix + di on [xi–1, xi], , and, , F(x) = Pi+1(x) = ai+1x3 + bi+1x2 + ci+1x + di+1 on [xi, xi+1].
Page 111 :
100, , NUMERICAL METHODS, , On each interval, we have four unknowns ai, bi, ci and di, i = 1, 2, ..., n. Therefore, the, total number of unknowns is 4n., Continuity of F(x), F′(x) and F″(x) on (a, b) implies the following., (i) Continuity of F(x) :, [xi–1, xi] : Pi (xi) = f(xi) = ai xi3 + bi xi2 + ci xi + di, , On, , On [xi, xi+1] : Pi+1(xi) = f(xi) = ai+1 xi3 + bi + 1 xi2 + ci + 1 xi + di + 1, i = 1, 2, ..., n – 1., , (2.49), , (ii) Continuity of F′(x) :, 3ai xi2 + 2bi xi + ci = 3ai + 1 xi2 + 2bi + 1 xi + ci + 1 ,, , i = 1, 2, ..., n – 1., , (2.50), , i = 1, 2, ..., n – 1., , (2.51), , (iii) Continuity of F″ (x) :, 6aixi + 2bi = 6ai+1xi + 2bi+1,, , At the end points x0 and xn, we have the interpolation conditions, f(x0) = a1 x03 + b1 x02 + c1 x0 + d1,, f(xn) = an xn3 + bn xn2 + cn xn + dn ., , and, , (2.52), , We have 2(n – 1) equations from (2.49), (n – 1) equations from (2.50), (n – 1) equations, from (2.51) and 2 equations from (2.52). That is, we have a total of 4n – 2 equations. We need, two more equations to obtain the polynomial uniquely. There are various types of conditions, that can be prescribed to obtain two more equations. We shall consider the case of a natural, spline, in which we set the two conditions as F″(x0) = 0, F″(xn) = 0., The above procedure is a direct way of obtaining a cubic spline. However, we shall, derive a simple method to determine the cubic spline., Example 2.21 Find whether the following functions are cubic splines ?, (i) f(x) = 5x3 – 3x2, – 1 ≤ x ≤ 0, , (ii) f(x) = – 2x3 – x2, – 1 ≤ x ≤ 0, , = – 5x3 – 3x2, 0 ≤ x ≤ 1., , = 2x3 + x2, 0 ≤ x ≤ 1., , Solution In both the examples, f(x) is a cubic polynomial in both intervals (– 1, 0) and (0, 1)., (i) We have, lim f ( x) = 0 = lim− f ( x) ., , x → 0+, , x→0, , The given function f(x) is continuous on (– 1, 1)., f ′(x) = 15x2 – 6x,, , –1≤x≤0, , = – 15x2 – 6x,, We have, , 0 ≤ x ≤ 1., , lim f ′( x) = 0 = lim− f ′( x) ., , x → 0+, , x→0, , The function f ′(x) is continuous on (– 1, 1)., f ″(x) = 30x – 6,, = – 30x – 6,, , –1≤x≤0, 0 ≤ x ≤ 1.
Page 112 :
101, , INTERPOLATION AND APPROXIMATION, , We have, , lim f ′′( x) = − 6 = lim− f ′′( x) ., , x → 0+, , x→0, , The function f ″(x) is continuous on (– 1, 1)., We conclude that the given function f(x) is a cubic spline., (ii) We have, lim f ( x) = 0 = lim− f ( x) ., , x → 0+, , x→0, , The given function f(x) is continuous on (– 1, 1)., f ′(x) = – 6x2 – 2x,, , –1≤x≤0, , = 6x2 + 2x,, We have, , 0 ≤ x ≤ 1., , lim f ′( x) = 0 = lim− f ′( x), , x → 0+, , x→0, , The function f ′(x) is continuous on (– 1, 1)., f ″(x) = – 12x – 2, – 1 ≤ x ≤ 0, = 12x + 2,, We have, , 0 ≤ x ≤ 1., , lim f ′′( x) = 2 , lim− f ′′( x) = – 2, , x → 0+, , x→0, , The function f ″(x) is not continuous on (– 1, 1)., We conclude that the given function f(x) is not a cubic spline., Cubic spline, From the definition, the spline is a piecewise continuous cubic polynomial. Hence,, F″(x) is a linear function of x in all the intervals., Consider the interval [xi–1, xi]. Using Lagrange interpolation in this interval, F ″(x) can, be written as, , Denote, , F″(x) =, , x − xi, x − xi − 1, F ′′ ( xi −1 ) +, F ′′( xi ), xi −1 − xi, xi − xi − 1, , =, , xi − x, x − xi − 1, F ′′ ( xi −1 ) +, F ′′( xi ), xi − xi − 1, xi − xi − 1, , (2.53), , F″(xi–1) = Mi–1, and F″(xi) = Mi., , Integrating (2.53) with respect to x, we get, F ′(x) = –, , ( xi − x) 2, ( x − xi −1 ) 2, Mi − 1 +, Mi + a ., 2( xi − xi − 1 ), 2( xi − xi −1 ), , (2.54), , Integrating (2.54) again with respect to x, we get, F(x) =, , ( xi − x) 3, ( x − xi − 1 ) 3, Mi − 1 +, Mi + ax + b, 6( xi − xi − 1 ), 6( xi − xi − 1 ), , where a, b are arbitrary constants to be determined by using the conditions, , (2.55)
Page 113 :
102, , NUMERICAL METHODS, , F(xi–1) = f(xi–1) and F(xi) = f(xi )., , (2.56), , Denote xi – xi–1 = hi, f(xi–1) = fi–1, and f(xi) = fi. Note that hi is the length of the interval, [xi–1, xi]., To ease the computations, we write, ax + b = c(xi – x) + d(x – xi–1) where a = d – c, b = c xi – d xi–1., That is, we write (2.55) as, , ( xi − x) 3, ( x − xi − 1 ) 3, M, M i + c( xi − x) + d( x − xi −1 ) ., +, F(x) =, i−1, 6 hi, 6 hi, Using the condition F(xi–1) = f(xi–1) = fi–1, we get, , ( xi − xi − 1 ) 3, h3, Mi − 1 + c( xi − xi −1 ) = i Mi − 1 + chi, 6 hi, 6 hi, , fi–1 =, , or, , c=, , LM, MN, , OP, PQ, , h2, 1, fi − 1 − i M i − 1 ., hi, 6, , Using the condition F(xi) = f(xi) = fi, we get, , or, , fi =, , ( xi − xi − 1 ) 3, h3, Mi + d( xi − xi − 1 ) = i M i + dhi, 6 hi, 6 hi, , d=, , h2, 1, fi − i M i ., hi, 6, , LM, MN, , OP, PQ, , Substituting the expressions for c and d in (2.55), we obtain the spline in the interval [xi–1, xi], as, , LM, MN, , h2, ( x − x), 1, fi−1 − i M i− 1, [( xi − x)3 Mi −1 + ( x − xi −1 ) 3 Mi ] + i, hi, 6hi, 6, , Fi(x) =, , +, , LM, MN, , ( x − xi −1 ), h2, fi − i Mi, 6, hi, , OP, PQ, , OP, PQ, , (2.57), , Note that the spline second derivatives Mi–1, Mi are unknowns and are to be determined., Setting i = i + 1 in (2.57), we get the spline valid in the interval [xi, xi+1] as, Fi+1(x) =, , LM, MN, , ( x − x), h2, 1, fi − i + 1 M i, [( xi + 1 − x) 3 M i + ( x − xi )3 Mi +1 ] + i − 1, hi + 1, 6hi + 1, 6, , +, , LM, MN, , ( x − xi ), h2, fi + 1 − i + 1 M i + 1, 6, hi + 1, , OP, PQ, , where hi+1 = xi+1 – xi. Differentiating (2.57) and (2.58), we get, , OP, PQ, , (2.58)
Page 114 :
103, , INTERPOLATION AND APPROXIMATION, , 1, [ − 3( xi − x) 2 M i −1 + 3( x − xi − 1 ) 2 M i ], 6hi, , F ′i(x) =, , −, , LM, MN, , OP, PQ, , LM, MN, , h2, h2, 1, 1, fi − 1 − i M i − 1 +, fi − i M i, hi, hi, 6, 6, , valid in the interval [xi–1, xi], and, , OP, PQ, , (2.59), , F′i+1(x) =, , 1, [ − 3( x i +1 − x ) 2 M i + 3( x − x i ) 2 M i +1 ], 6hi +1, , −, , h2, 1, h2, 1, fi + 1 − i + 1 M i + 1, fi − i +1 M i +, hi + 1, 6, hi +1, 6, , LM, MN, , LM, MN, , OP, PQ, , OP, PQ, , (2.60), , valid in the interval [xi, xi +1]., Now, we require that the derivative F ′(x) be continuous at x = xi. Hence, the left hand, and right hand derivatives of F′(x) at x = xi must be equal, that is,, lim Fi′ ( xi − ε) = lim Fi′+ 1 ( xi + ε) ., , ε→0, , ε→0, , Using (2.59) and (2.60), we obtain, hi, h, h, 1, 1, Mi −, fi − 1 + i M i − 1 +, fi − i M i, 2, 6, 6, hi, hi, , =–, , or, , hi + 1, h, h, 1, 1, Mi −, fi + i + 1 M i +, fi + 1 − i + 1 M i + 1, hi + 1, hi + 1, 2, 6, 6, , hi, h, 1, 1, 1, M i − 1 + ( hi + hi + 1 ) M i + i + 1 M i + 1 =, ( fi + 1 − fi ) −, ( f i − fi − 1 ), 6, 3, 6, hi + 1, hi, , i = 1, 2, ..., n – 1., , (2.61), , This relation gives a system of n – 1 linear equations in n + 1 unknowns M0, M1, ..., Mn., The two additional conditions required are the natural spline conditions M0 = 0 = Mn. These, equations are solved for M1, M2, ..., Mn–1. Substituting these values in (2.57), we obtain the, spline valid in the interval [xi–1, xi]. If the derivative is required, we can find it from (2.59)., Equispaced data When the data is equispaced, we have hi = hi+1 = h and xi = x0 + ih. Then, the, spline in the interval [xi–1, xi], given in (2.57) and the relation between the second derivatives, given in (2.61) simplify as, Fi(x) =, , +, , 1, [( x i − x )3 M i −1 + ( x − x i −1 )3 M i ], 6h, , LM, MN, , OP, PQ, , LM, N, , ( xi − x ), h2, ( x − xi −1 ), h2, fi −1 −, M i −1 +, fi −, Mi, 6, h, 6, h, , OP, Q, , (2.62)
Page 115 :
104, , NUMERICAL METHODS, , Mi–1 + 4Mi + Mi+1 =, , 6, h2, , ( fi + 1 − 2 fi + fi − 1 ), , (2.63), , i = 1, 2, ..., n – 1., Remark 12 Splines provide better approximation to the behaviour of functions that have, abrupt local changes. Further, splines perform better than higher order polynomial approximations., Example 2.22 Obtain the cubic spline approximation for the following data., x, , 0, , 1, , 2, , f(x), , –1, , 3, , 29, , with M0 = 0, M2 = 0. Hence, interpolate at x = 0.5, 1.5., Solution We have equispaced data with h = 1. We obtain from (2.63),, Mi–1 + 4Mi + Mi+1 = 6(fi+1 – 2fi + fi–1), i = 1., For i = 1, we get, M0 + 4M1 + M2 = 6(f2 – 2f1 + f0)., Since, M0 = 0, M2 = 0, we get, 4M1 = 6[29 – 2(3) – 1] = 132, or M1 = 33., The spline is given by, Fi(x) =, , LM, N, , OP, Q, , LM, N, , 1, 1, 1, [( xi − x)3 Mi − 1 + ( x − xi − 1 ) 3 Mi ] + ( xi − x) fi − 1 − M i − 1 + (x – xi–1) fi − M i, 6, 6, 6, , We have the following splines., On [0, 1]:, F(x) =, , FG, H, , IJ, K, , 1, 1, (33)x3 + (1 – x)(– 1) + x 3 − (33), 6, 6, , =, , 1, (11x3 – 3x – 2)., 2, , On [1, 2]:, F(x) =, =, , LM, N, , OP, Q, , LM, N, , OP, Q, , LM, N, , OP, Q, , LM, N, , OP, Q, , 1, 1, 1, [(x1 – x)3 M0 + (x – x0)3 M1] + (x1 – x) f0 − M0 + ( x − x0 ) f1 − M1, 6, 6, 6, , =, , 1, 1, 1, [( x2 − x) 3 M 1 + ( x − x1 ) 3 M2 ] + ( x2 − x) f1 − M1 + ( x − x1 ) f2 − M2, 6, 6, 6, , LM, N, , OP, Q, , OP, Q, , 1, 1, [(2 − x) 3 (33)] + (2 − x) 3 − (33) + ( x − 1) [29], 6, 6
Page 116 :
105, , INTERPOLATION AND APPROXIMATION, , =, , 11, 63, (2 − x) 3 +, x – 34., 2, 2, , Since, 0.5 lies in the interval (0, 1), we obtain, F(0.5) =, , FG, H, , IJ, K, , 1 11 3, 17, − −2 =−, ., 2 8 2, 16, , Since, 1.5 lies in the interval (1, 2), we obtain, F(1.5) =, , 1, 223, [11(2 − 15, . ) 3 + 63(1.5) − 68] =, ., 2, 16, , Example 2.23 Obtain the cubic spline approximation for the following data., x, , 0, , 1, , 2, , 3, , f(x), , 1, , 2, , 33, , 244, , with M0 = 0, M3 = 0. Hence, interpolate at x = 2.5., Solution We have equispaced data with h = 1. We obtain from (2.63),, Mi–1 + 4Mi + Mi+1 = 6(fi+1 – 2fi + fi–1) i = 1, 2., For i = 1, we get, M0 + 4M1 + M2 = 6(f2 – 2f1 + f0) = 6(33 – 4 + 1) = 180., For i = 2, we get, M1 + 4M2 + M3 = 6(f3 – 2f2 + f1) = 6(244 – 66 + 2) = 1080., Since, M0 = 0, M3 = 0, we get, 4M1 + M2 = 180, M1 + 4M2 = 1080., The solution is, , M1 = – 24, M2 = 276., , The cubic splines in the corresponding intervals are as follows., On [0, 1]:, F(x) =, =, On [1, 2]:, F(x) =, =, , LM, N, , OP, Q, , LM, N, , 1, 1, 1, [( x1 − x) 3 M 0 + ( x − x0 ) 3 M 1 ] + ( x1 − x) f0 − M 0 + (x – x0) f1 − M1, 6, 6, 6, , LM, N, , OP, Q, , OP, Q, , 1 3, 1, x (− 24) + (1 − x) + x 2 − (− 24) = − 4 x 3 + 5 x + 1 ., 6, 6, , LM, OP, LM, OP, N, Q, N, Q, L 1 O, L 1 O, (276)] + (2 – x) M2 − ( − 24) P + ( x − 1) M33 − (276) P, N 6 Q, N 6 Q, , 1, 1, [( x2 − x)3 M 1 + ( x − x1 ) 3 M2 ] + ( x2 − x) f1 − M1 + (x – x1) f2 − 1 M 2, 6, 6, 6, 1, [(2 – x)3 (– 24) + (x – 1)3, 6
Page 117 :
106, , NUMERICAL METHODS, , =, , 1, [(8 – 12x + 6x2 – x3)(– 24) + (x3 – 3x2 + 3x – 1)(276)] + 6(2 – x) – 13(x – 1), 6, , = 50x3 – 162x2 + 167x – 53., On [2, 3]:, F(x) =, =, , LM, N, , OP, Q, , LM, N, , 1, 1, 1, [( x3 − x) 3 M2 + ( x − x2 ) 3 M3 ] + ( x3 − x) f2 − M2 + (x – x2) f3 − M 3, 6, 6, 6, , LM, N, , OP, Q, , OP, Q, , 1, 1, [(3 − x) 3 (276)] + (3 − x) 33 − (276) + (x – 2)(244), 6, 6, , 1, [(27 – 27x + 9x2 – x3) (276)] – 13(3 – x) + 244(x – 2), 6, = – 46x3 + 414 x2 – 985 x + 715., , =, , The estimate at x = 2.5 is, F(2.5) = – 46(2.5)3 + 414(2.5)2 – 985(2.5) + 715 = 121.25., , REVIEW QUESTIONS, 1. What are the advantages of cubic spline fitting?, Solution Splines provide better approximation to the behaviour of functions that have, abrupt local changes. Further, splines perform better than higher order polynomial, approximations., 2. Write the relation between the second derivatives, , M i (x ) in cubic splines with equal, , mesh spacing., Solution The required relation is, Mi–1 + 4Mi + Mi+1 =, , 6, h2, , ( fi+1 – 2fi + fi–1),, , i = 1, 2, ..., n – 1., , 3. Write the end conditions on Mi(x) in natural cubic splines., Solution The required conditions are M0(x) = 0, Mn(x) = 0., , EXERCISE 2.3, Are the following functions cubic splines?, 1. f(x) = x3 – 2x + 3,, =, , 2x3, , 2. f(x) =, , 5x3, , =, , 2x3, , 0 ≤ x ≤ 1,, , –, , 3x2, , + x + 2,, , 1 ≤ x ≤ 2., , –, , 3x2, , + 1,, , 0 ≤ x ≤ 1,, , +, , 6x2, , – 9x + 4,, , 1 ≤ x ≤ 2.
Page 118 :
107, , INTERPOLATION AND APPROXIMATION, , 3. f(x) = 3x2 + x + 1,, =, , 3x2, , – 5x + 1,, , 4. f(x) =, , x3, , 3x2, , –, , =, , x3, , – 2,, , + 1,, , 0 ≤ x ≤ 1,, 1 < x ≤ 2., 0 ≤ x ≤ 1,, 1 ≤ x ≤ 2., , 5. Find the values of α, β such that the given function is a cubic spline., f(x) = α x3 + β x2 + 2x, – 1 ≤ x ≤ 0., = 3x3 + x2 + 2x,, , 0 ≤ x ≤ 1., , 6. Obtain the cubic spline approximation valid in the interval [3, 4], for the function given, in the tabular form, under the natural cubic spline conditions, f ″(1) = M(1) = 0, and f ″(4) = M(4) = 0., x, , 1, , 2, , 3, , 4, , f(x), , 3, , 10, , 29, , 65, , 7. Obtain the cubic spline approximation valid in the interval [1, 2], for the function given, in the tabular form, under the natural cubic spline conditions f ″(0) = M(0) = 0, and f ″(3), = M(3) = 0. Hence, interpolate at x = 1.5., x, , 0, , 1, , 2, , 3, , f(x), , 1, , 4, , 10, , 8, , 8. Fit the following four points by the cubic spline using natural spline conditions, M(1) = 0, M(4) = 0., x, , 1, , 2, , 3, , 4, , f(x), , 1, , 5, , 11, , 8, , Hence, estimate f(1.5)., 9. Fit the following four points by the cubic spline using natural spline conditions, M(1) = 0, M(4) = 0., x, , 1, , 2, , 3, , 4, , f(x), , 0, , 1, , 0, , 0, , 10. The following values of x and y are given, x, , 1, , 2, , 3, , 4, , f(x), , 1, , 2, , 5, , 11, , Find the cubic splines and evaluate y(1.5)., , (A.U. Nov/Dec 2004)
Page 120 :
!, Numerical Differentiation, and Integration, , 3.1, , INTRODUCTION, , We assume that a function f(x) is given in a tabular form at a set of n + 1 distinct points x0, x1,, ..., xn. From the given tabular data, we require approximations to the derivatives f (r) (x′), r ≥ 1,, where x′ may be a tabular or a non-tabular point. We consider the cases r = 1, 2., In many applications of Science and engineering, we require to compute the value of the, definite integral, , z, , b, , a, , f ( x) dx , where f(x) may be given explicitly or as a tabulated data. Even, , when f(x) is given explicitly, it may be a complicated function such that integration is not, easily carried out., In this chapter, we shall derive numerical methods to compute the derivatives or evaluate an integral numerically., , 3.2, , NUMERICAL DIFFERENTIATION, , Approximation to the derivatives can be obtained numerically using the following two, approaches, (i) Methods based on finite differences for equispaced data., (ii) Methods based on divided differences or Lagrange interpolation for non-uniform data., 3.2.1 Methods Based on Finite Differences, 3.2.1.1 Derivatives Using Newton’s Forward Difference Formula, Consider the data (xi, f(xi)) given at equispaced points xi = x0 + ih, i = 0, 1, 2, ..., n where h is the, step length. The Newton’s forward difference formula is given by, , 109
Page 122 :
111, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , At x = x0, that is, at s = 0, we obtain the approximation to the derivative f ″(x) as, f ″(x0) =, , 1, h, , 2, , LM∆ f, N, 2, , 0, , − ∆3 f0 +, , OP, Q, , 11 4, 5, 137 6, ∆ f0 − ∆5 f0 +, ∆ f0 − ... ., 12, 6, 180, , We use formulas (3.3) and (3.5) when the entire data is to be used., , (3.6), , Very often, we may require only lower order approximations to the derivatives. Taking, a few terms in (3.4), we get the following approximations., Taking one term in (3.4), we get, , or, in general,, , f ′(x0) =, , 1, 1, ∆ f0 =, [f(x1) – f(x0)],, h, h, , f ′(xk) =, , 1, 1, ∆ fk =, [f(xk+1) – f(xk)]., h, h, , (3.7), , Taking two terms in (3.4), we get, f ′(x0) =, =, or, in general,, , f ′(xk) =, , LM, N, , OP, Q, , LM, N, , 1, 1, 1, 1, ∆f0 − ∆2 f0 =, { f ( x1 ) − f ( x0 )} − { f ( x2 ) − 2 f ( x1 ) + f ( x0 )}, h, h, 2, 2, , OP, Q, , 1, [− 3 f ( x0 ) + 4 f ( x1 ) − f ( x2 )], 2h, , (3.8), , 1, [– 3f(xk) + 4f(xk+1) – f(xk+2)]., 2h, , (3.9), , Similarly, we have the approximation for f ″(x0) as, f ″(x0) =, or, in general,, , f ″(xk) =, , 1, h2, 1, h2, , ∆2 f0 =, , 1, h2, , [ f ( x2 ) − 2 f ( x1 ) + f ( x0 )], , [ f ( x k+ 2 ) − 2 f ( xk + 1 ) + f ( x k )] ., , (3.10), , Errors of approximations. Using Taylor series approximations, we obtain the error in the, formula (3.7) for f ′(x) at x = xk as, E(f, xk) = f ′(xk) –, = f ′ (xk) –, =–, , 1, [ f ( xk + h) − f ( xk )], h, , LM, N, , h2, 1, f ′′ ( xk ) + ...} − f ( xk ), { f ( xk ) + hf ′ ( xk ) +, h, 2, , h, f ′′( xk ) + ..., 2, , The error is of order O(h), or the formula is of first order., The error in the formula (3.8) for f ′(x) at x = xk is obtained as, E(f, xk) = f ′(xk) –, , 1, [– 3 f(xk) + 4f(xk+1) – f(xk+2)], 2h, , OP, Q, (3.11)
Page 123 :
112, , NUMERICAL METHODS, , = f ′( x k ) −, , LM, MN, , RS, T, , RS, T, , – f ( x k ) + 2 hf ′ ( xk ) +, , =, , UV, W, , 1, h2, h3, − 3 f ( x k ) + 4 f ( x k ) + hf ′( x k ) +, f ′′( xk ) +, f ′′′( xk ) + ..., 2h, 2, 6, , UVOP, WPQ, , (2h) 2, (2h) 3, f ′′ ( xk ) +, f ′′′( xk ) + ..., 2, 6, , h2, f ′′′( x k ) + ..., 3, , (3.12), , The error is of order O(h2), or the formula is of second order., The error in the formula (3.9) for f ″(x) at x = xk is obtained as, E(f, xk) = f ″ (xk) –, = f ″ (xk) –, , RS, T, , 1, h2, 1, h2, , [f(xk + 2h) – 2 f(xk + h) + f(xk)], , LMR f (x ) + 2hf ′(x ) + (2h), 2, MNST, k, , – 2 f ( x k ) + hf ′( x k ) +, , k, , 2, , f ′′( xk ) +, , UV, W, , h2, h3, f ′′( x k ) +, f ′′′( x k ) + ... + f ( xk ), 2, 6, , = – h f ″′(xk) + ..., , UV, W, , (2h) 3, f ′′′( x k ) + ..., 6, , OP, PQ, , (3.13), , The error is of order O(h), or the formula is of first order., Remark 1 It can be noted that on the right hand side of the approximation to f ′(x), we have, the multiplying factor 1/h, and on the right hand side of the approximation to f ′′(x), we have, the multiplying factor 1/h2. Since h is small, this implies that we may be multiplying by a, large number. For example, if h = 0.01, the multiplying factor on the right hand side of the, approximation to f ′(x) is 100, while the multiplying factor on the right hand side of the, approximation to f ′′(x) is 10000. Therefore, the round-off errors in the values of f(x) and hence, in the forward differences, when multiplied by these multiplying factors may seriously effect, the solution and the numerical process may become unstable. This is one of the drawbacks of, numerical differentiation., Remark 2 Numerical differentiation must be done with care. When a data is given, we do not, know whether it represents a continuous function or a piecewise continuous function. It is, possible that the function may not be differentiable at some points in its domain. What happens, if we try to find the derivatives at these points where the function is not differentiable? For, example, if f(x) = | x |, and a data is prepared in the interval [– 1, 1], what value do we get, when we try to find f ′(x) at x = 0, where the function is not differentiable?, Remark 3 We use the forward difference formulas for derivatives, when we need the values, of the derivatives at points near the top of the table of the values.
Page 124 :
113, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Example 3.1 Find dy/dx at x = 1 from the following table of values, x, , 1, , 2, , 3, , 4, , y, , 1, , 8, , 27, , 64, , Solution We have the following forward difference table., Forward difference table. Example 3.1., x, , y, , 1, , 1, , ∆ 2y, , ∆y, , ∆ 3y, , 7, 2, , 8, , 3, , 27, , 12, 19, , 6, 18, , 37, 4, , 64, , We have h = 1, x0 = 1, and x = x0 + sh = 1 + s. For x = 1, we get s = 0., Therefore,, , FG, H, , dy, 1, 1, 1, (1) =, ∆f0 − ∆2 f0 + ∆3 f0, dx, h, 2, 3, =7–, , IJ, K, , 1, 1, (12) + (6) = 3., 2, 3, , Example 3.2 Using the operator relations, derive the approximations to the derivatives f ′(x0), and f ′′(x0) in terms of forward differences., Solution From the operator relation E = e hD, where D = d/dx, we obtain, hDf(x0) = log E[ f(x0)] = log (1 + ∆) f(x0), , LM, N, , = ∆−, , or, , f ′(x0) =, , OP, Q, , ∆2 ∆3 ∆4 ∆5, +, −, +, − ... f(x0), 2, 3, 4, 5, , LM, N, , OP, Q, , 1, 1, 1, 1, 1, ∆f0 − ∆2 f0 + ∆3 f0 − ∆4 f0 + ∆5 f0 − ..., h, 2, 3, 4, 5, , h2D2 f(x0) = [log (1 + ∆)]2 f(x0), , L ∆, = M∆ −, N 2, , 2, , OP, Q, , ∆3 ∆4 ∆5, +, −, +, − ..., 3, 4, 5, , 2, , f(x0)
Page 125 :
114, , NUMERICAL METHODS, , LM, N, , 2, 3, = ∆ −∆ +, , or, , f ″(x0) =, , LM∆ f, N, , 1, , 2, , h2, , 0, , OP, Q, , 11 4 5 5 137 6, ∆ − ∆ +, ∆ + ... f ( x0 ), 12, 6, 180, , − ∆3 f0 +, , OP, Q, , 11 4, 5, 137 6, ∆ f0 − ∆5 f0 +, ∆ f0 − ..., 12, 6, 180, , Example 3.3 Find f ′(3) and f ″(3) for the following data:, x, , 3.0, , 3.2, , 3.4, , 3.6, , 3.8, , 4.0, , f(x), , – 14, , – 10.032, , – 5.296, , – 0.256, , 6.672, , 14, , [A.U. April/May 2005], Solution We have h = 0.2 and x = x0 + sh = 3.0 + s(0.2). For x = 3, we get s = 0., We have the following difference table., Forward difference table. Example 3.3., x, , f(x), , 3.0, , – 14, , ∆2 f, , ∆f, , ∆3 f, , ∆4 f, , ∆5 f, , 3.968, 3.2, , – 10.032, , 0.768, 4.736, , 3.4, , – 0.464, , – 5.296, , 0.304, , 2.048, , 5.040, 3.6, , 1.584, , – 0.256, , 1.888, , – 3.072, , 6.928, 3.8, , 6.672, , 4.0, , 14, , – 5.120, , –1.488, 0.400, , 7.328, , We have the following results:, f ′(x0) =, , LM, N, , 1, 1, 1, 1, 1, ∆f0 − ∆2 f0 + ∆3 f0 − ∆4 f0 + ∆5 f0, h, 2, 3, 4, 5, , OP, Q, , LM, N, 1 L, 11, 5, O, ∆ f −∆ f +, ∆ f − ∆ f P, f ″(x ) =, M, 12, 6, h N, Q, 1 L, 11, 5, O, (2.048) − (− 5.12)P = 184.4, 0.768 + 0.464 +, f ″ (3.0) =, M, 0.04 N, 12, 6, Q, f ′ (3.0) =, , 0, , OP, Q, , 1, 1, 1, 1, 1, 3.968 − (0.768) + (− 0.464) − (2.048) + (− 5.120) = 9.4667., 0.2, 2, 3, 4, 5, 2, , 2, , 0, , 3, , 0, , 4, , 0, , 5, , 0
Page 126 :
115, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Example 3.4 The following data represents the function f(x) = e2x. Using the forward differences and the entire data, compute the approximation to f′(0.3). Also, find the first order and, second order approximations to f′(0.3). Compute the approximation to f′′(0.3) using the entire, data and the first order approximation. Compute the magnitudes of actual errors in each case., x, , 0.0, , 0.3, , 0.6, , 0.9, , 1.2, , f (x), , 1.0000, , 1.8221, , 3.3201, , 6.0496, , 11.0232, , Solution The step length is h = 0.3 and x = x0 + sh = 0.0 + s(0.3). For x = 0.3, we get, s = 1. We have the following forward difference table., Forward difference table. Example 3.4., x, , f(x), , 0.0, , 1.0000, , ∆2 f, , ∆f, , ∆3 f, , ∆4 f, , 0.8221, 0.3, , 1.8221, , 0.6, , 3.3201, , 0.6759, 1.4980, , 0.5556, 1.2315, , 2.7295, 0.9, , 0.4570, 1.0126, , 6.0496, , 2.2441, 4.9736, , 1.2, , 11.0232, , From (3.3), we have the following approximation for s = 1., f ′(x0 + sh) = f ′(x0 + h) =, , f ′(0.3) =, , LM, N, , LM, N, , 1, 1, 1, 1 4, ∆f0 + ∆2 f0 − ∆3 f0 +, ∆ f0, h, 2, 6, 12, , 1, 1, ∆ f(0.3) =, [f (0.6) – f(0.3)], h, 0.3, =, , From (3.9),, , f ′(xk) =, , OP, Q, , 1, 1, 1, 1, 0.8221 + ( 0.6759) − ( 0.5556) +, ( 0.4570) = 3.6851., 0.3, 2, 6, 12, , The first order approximation gives, f ′(0.3) =, , OP, Q, , 1, 1.4980, [3.3201 – 1.8221] =, = 4.9933., 0.3, 0.3, 1, [– 3 f(xk) + 4 f(xk+1) – f(xk+2)]., 2h
Page 127 :
116, , NUMERICAL METHODS, , We get the second order approximation as, f ′(0.3) =, =, , 1, [– 3 f(0.3) + 4 f(0.6) – f(0.9)], 0.6, 1, [– 3(1.8221) + 4(3.3201) – 6.0496] = 2.9408., 0.6, , f′(0.3) = 2e0.6 = 2(1.8221) = 3.6442., , The exact value is, , The errors in the approximations are as follows:, First order approximation:, , | 4.9933 – 3.6442 | = 1.3491., , Second order approximation: | 2.9408 – 3.6442 | = 0.7034., Full data:, , | 3.6851 – 3.6442 | = 0.0409., , From (3.5), we have the following approximation for s = 1., f ″(x0 + sh) = f ″(x0 + h) =, f ″(0.3) =, , 1, h, , 2, , LM, N, , LM∆ f, N, 2, , 0, , −, , 1 4, ∆ f0, 12, , OP, Q, , OP, Q, , 1, 1, 0.6759 −, (0.4570) = 7.0869 ., 0.09, 12, , The first order approximation gives, f ″(0.3) =, =, , 1, h, , 2, , ∆2 f(0.3) =, , 1, [f(0.9) – 2f(0.6) + f(0.3)], h2, , 1, [6.0496 – 2(3.3201) + 1.8221] = 13.6833., 0.09, , The exact value is f ″(0.3) = 4e0.6 = 7.2884, The errors in the approximations are as follows:, First order approximation:, , | 13.6833 – 7.2884 | = 6.3949., , Full data:, , | 7.0869 – 7.2884 | = 0.2015., , Example 3.5 The following data gives the velocity of a particle for 8 seconds at an interval of, 2 seconds. Find the initial acceleration using the entire data., Time (sec), , 0, , 2, , 4, , 6, , 8, , Velocity (m/sec), , 0, , 172, , 1304, , 4356, , 10288, , Solution If v is the velocity, then initial acceleration is given by, , FG dv IJ, H dt K, , ., t =0, , We shall use the forward difference formula to compute the first derivative at t = 0. The, step length is h = 2., We form the forward difference table for the given data.
Page 128 :
117, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Forward difference table. Example 3.5., x, , f(x), , 0, , 0, , ∆2 f, , ∆f, , ∆3 f, , ∆4 f, , 172, 2, , 172, , 960, 1132, , 4, , 1304, , 6, , 4356, , 960, 1920, , 3052, , 0, 960, , 2880, 5932, , 8, , 10288, , We have the following result:, , LM, OP, N, Q, 1L, 1, 1, O, f ′(0) = M172 − (960) + (960) P = 6., 2N, 2, 3, Q, , f ′(x0) =, , 1, 1, 1, ∆f0 − ∆2 f0 + ∆3 f0 − ..., h, 2, 3, , 3.2.1.2 Derivatives Using Newton’s Backward Difference Formula, Consider the data (xi, f(xi)) given at equispaced points xi = x0 + ih, where h is the step length., The Newton’s backward difference formula is given by, f(x) = f(xn) + (x – xn), , 1, 1, ∇ f(xn) + (x – xn)(x – xn–1), ∇ 2 f(xn) + ..., 1! h, 2 ! h2, , + (x – xn)(x – xn–1) ... (x – x1), , 1, ∇n f(xn)., n ! hn, , (3.14), , Let x be any point near xn. Let x – xn = sh. Then, the formula simplifies as, f(x) = f(xn + sh) = f(xn) + s∇f(xn) +, , Note that, , s(s + 1) 2, s(s + 1)(s + 2) 3, ∇ f(xn) +, ∇ f(xn), 2!, 3!, , +, , s(s + 1)(s + 2)(s + 3) 4, s(s + 1)(s + 2)(s + 3)(s + 4) 5, ∇ f(xn) +, ∇ f(xn) + ..., 4!, 5!, , +, , s(s + 1)(s + 2) ... (s + n − 1) n, ∇ f(xn)., n!, , (3.15), , s = [(x – xn)/h] < 0., , The magnitudes of the successive terms on the right hand side become smaller and, smaller.
Page 130 :
119, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Remark 4 We use the backward difference formulas for derivatives, when we need the values, of the derivatives near the end of table of values., Example 3.6 Using the operator relation, derive approximations to the derivatives, f′(xn), f″(xn) in terms of the backward differences., Solution From the operator relation E = ehD, where D = d/dx, we obtain, hDf(xn) = [log E] f(xn) = log [(1 – ∇)–1] f(xn) = – log (1 – ∇) f(xn), , LM, MN, , = ∇+, , or, , f ′(xn) =, , OP, PQ, , ∇ 2 ∇3 ∇ 4 ∇5, +, +, +, + ... f(xn), 2, 3, 4, 5, , LM, N, , LM, N, , h2D2 f(xn) = [log (1 – ∇)]2 f(xn) = ∇ +, , LM, N, , = ∇2 + ∇3 +, or, , f ″ (xn) =, , OP, Q, O, + ...P, Q, , 1, 1, 1, 1, 1, ∇fn + ∇ 2 f n + ∇ 3 f n + ∇ 4 f n + ∇ 5 fn + ..., 2, 3, 4, 5, h, ∇2 ∇3 ∇4 ∇5, +, +, +, 2, 3, 4, 5, , OP, Q, , 11 4 5 5, ∇ + ∇ + ..., 12, 6, , LM, N, , 2, , f(xn), , f ( xn ), , OP, Q, , 1, 11 4, 5, ∇ 2 fn + ∇ 3 fn +, ∇ fn + ∇ 5 fn + ... ., 2, 12, 6, h, , Example 3.7 Find f ′(3) using the Newton’s backward difference formula, for the data, x, , 1.0, , 1.5, , 2.0, , 2.5, , 3.0, , f(x), , – 1.5, , – 2.875, , – 3.5, , – 2.625, , 0.5, , Solution The step length is h = 0.5 and x = xn + sh = 3.0 + s(0.5). For x = 3.0, we get, s = 0. We have the following backward difference table., Backward difference table. Example 3.7., x, , f(x), , 1.0, , – 1.5, , 1.5, , – 2.875, , ∇f, , ∇2 f, , ∇3 f, , ∇4 f, , – 1.375, 0.75, – 0.625, 2.0, , – 3.5, , 0.75, 1.5, , 0.875, 2.5, , – 2.625, , 2.25, 3.125, , 3.0, , 0.5, , 0.0, 0.75
Page 131 :
120, , NUMERICAL METHODS, , From the formula, f ′(xn) =, we obtain, , f ′(3) =, , LM, N, , OP, Q, , 1, 1, 1, 1, 1, ∇fn + ∇ 2 f n + ∇ 3 f n + ∇ 4 f n + ∇ 5 fn + ... ,, 2, 3, 4, 5, h, , LM, N, , OP, Q, , 1, 1, 1, 3.125 + (2.25) + (0.75) = 9., 0.5, 2, 3, , Example 3.8 Find f ′(2.5), f ′(2) and f ″(2.5) using the Newton’s backward difference method,, for the data of the function f(x) = ex + 1., x, , 1.0, , 1.5, , 2.0, , 2.5, , f(x), , 3.7183, , 5.4817, , 8.3891, , 13.1825, , Find the magnitudes of the actual errors., Solution The step length is h = 0.5 and x = xn + sh = 2.5 + s(0.5). For x = 2.5, we get, s = 0. The backward difference table is given below., Backward difference table. Example 3.8., x, , f(x), , 1.0, , 3.7183, , ∇f, , ∇2 f, , ∇3 f, , 1.7634, 1.5, , 5.4817, , 2.0, , 8.3891, , 1.1440, 2.9074, , 0.7420, 1.8860, , 4.7934, 2.5, , 13.1825, , From the formula, f ′(xn) =, we obtain, , f ′(2.5) =, , LM, N, , OP, Q, , 1, 1, 1, 1, 1, ∇f n + ∇ 2 fn + ∇ 3 fn + ∇ 4 fn + ∇ 5 fn + ... ,, 2, 3, 4, 5, h, , LM, N, , OP, Q, , 1, 1, 1, 4.7934 + (18860, ., ) + (0.7420) = 11.9675., 0.5, 2, 3, , The exact value is f ′(2.5) = e2.5 = 12.1875. The magnitude of the error in the solution is, | Error | = | 12.1875 – 11.9675 | = 0.2150., For x = 2.0, we get s = – 1. From the formula, f ′(xn–1) =, , LM, N, , OP, Q, , 1, 1, 1, 1 4, 1 5, ∇ fn − ∇ 2 f n − ∇ 3 f n −, ∇ fn −, ∇ fn + ... ,, 2, 6, 12, 20, h
Page 132 :
121, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , LM, OP, N, Q, 1 L, 1, 1, O, 4.7934 − (1.8860) − (0.7420)P = 7.4535., =, M, 0.5 N, 2, 6, Q, , we get, , f ′(2) =, , 1, 1, 1, ∇ f n − ∇ 2 fn − ∇ 3 fn, 0.5, 2, 6, , The exact value is f ′(2) = e2 = 7.3891. The magnitude of the error in the solution is, | Error | = | 7.3891 – 7.4535 | = 0.0644., For x = 2.5, we get s = 0. From the formula, f ″(xn) =, we get, , f ′′(2.5) =, , 1, h, , 2, , LM∇ f, N, 2, , n, , + ∇ 3 fn +, , OP, Q, , 11 4, 5, ∇ fn + ∇5 fn + ... ,, 12, 6, , 1, [1.8660 + 0.7420] = 10.5120., 0.25, , The exact value is f ′′(2.5) = e2.5 = 12.1875. The magnitude of the error in the solution is, | Error | = | 12.1875 – 10.5120 | = 1.6705., Example 3.9 The following data represents the function f(x) = e2x., x, , 0.0, , 0.3, , 0.6, , 0.9, , 1.2, , f(x), , 1.0000, , 1.8221, , 3.3201, , 6.0496, , 11.0232, , Find f ′(1.2) f ′(0.9) and f ″(1.2), using the Newton’s backward difference method., Compute the magnitudes of the errors., Solution The step length is h = 0.3. We have the following backward difference table., Backward difference table. Example 3.9., x, , f(x), , 0.0, , 1.0000, , 0.3, , 1.8221, , ∇f, , ∇2 f, , ∇3 f, , ∇4 f, , 0.8221, 0.6759, 1.4980, 0.6, , 3.3201, , 0.5556, 1.2315, , 2.7295, 0.9, , 6.0496, , 2.2441, 4.9736, , 1.2, , 11.0232, , 0.4570, 1.0126
Page 133 :
122, , NUMERICAL METHODS, , From x = xn + sh = 1.2 + s(0.3), we get for x = 1.2, s = 0. Using the formula, , OP, Q, 1 L, 1, 1, 1, O, 4.9736 + (2.2441) + (1.0126) + (0.4570) P = 21.8248., f ′(1.2) =, M, 0.3 N, 2, 3, 4, Q, f ′(xn) =, , we get, , LM, N, , 1, 1, 1, 1, 1, ∇fn + ∇ 2 fn + ∇ 3 fn + ∇ 4 fn + ∇ 5 fn + ... ,, h, 2, 3, 4, 5, , The exact value is f ′(1.2) = 2e2.4 = 22.0464., The magnitude of the error is, | Error | = | 22.0464 – 21.8248 | = 0.2216., From x = xn + sh = 1.2 + s(0.3), we get for x = 0.9, s = – 1. Using the formula, , OP, Q, 1 L, 1, 1, 1, O, 4.9736 − (2.2441) − (1.0126) −, (0.4570) P = 12.1490., f ′(0.9) =, M, 0.3 N, 2, 6, 12, Q, , f ′(xn–1) =, we get, , LM, N, , 1, 1, 1, 1 4, 1 5, ∇fn − ∇ 2 fn − ∇3 fn −, ∇ fn −, ∇ fn + ... ,, h, 2, 6, 12, 20, , The exact value is f ′(0.9) = 2e1.8 = 12.0993., The magnitude of the error is, | Error | = | 12.0993 – 12.1490 | = 0.0497., From x = xn + sh = 1.2 + s(0.3), we get for x = 1.2, s = 0. Using the formula, , LM∇ f + ∇ f + 11 ∇ f + 5 ∇ f + ...OP ,, 12, 6, Q, h N, 1 L, 11, O, 2.2441 + 1.0126 +, (0.4570) P = 40.8402., f ″(1.2) =, 0.09 MN, 12, Q, f ″ (xn) =, , we get, , 1, , 2, , 2, , n, , 3, , n, , 4, , n, , 5, , n, , The exact value is f ″(1.2) = 4e2.4 = 44.0927., The magnitude of the error is, | Error | = | 40.8402 – 44.0927 | = 3.2525., 3.2.1.3 Derivatives Using Divided Difference Formula, The divided difference interpolation polynomial fitting the data (xi, f(xi)), i = 0, 1, 2,…, n is, given by, f(x) = f(x0) + (x – x0) f [x0, x1] + (x – x0)(x – x1) f [x0, x1, x2] + ..., + (x – x0)(x – x1) (x – x2) f [x0, x1, x2] + ..., + (x – x0)(x – x1) ... (x – xn–1) f [x0, x1,... xn], , (3.22)
Page 135 :
124, , NUMERICAL METHODS, , we obtain, , f ′(1.6) = 0.81094 + [(1.6 – 1.0) + (1.6 – 1.5)] (– 0.23558) + [(1.6 – 1.5)(1.6 – 2.0), + (1.6 – 1.0)(1.6 – 2.0) + (1.6 – 1.0)(1.6 – 1.5)] (0.061157), = 0.81094 + 0.7 (– 0.23558) – 0.22(0.061157) = 0.63258., , Substituting x = 1.6 in the formula, f ″(x) = 2 f [x0, x1, x2] + 2[(x – x0) + (x – x1) + (x – x2)] f [x0, x1, x2, x3], we obtain, , f ″(1.6) = 2(– 0.23558) + 2[(1.6 – 1.0) + (1.6 – 1.5) + (1.6 – 2.0)](0.061157), = – 0.47116 + 0.03669 = – 0.43447., , Remark 5 Often, in applications, we require the maximum and/ or minimum of a function, given as a tabulated data. We may obtain the interpolation polynomial, differentiate it and, set it equal to zero to find the stationary points. Alternatively, we can use the numerical, differentiation formula for finding the first derivative, set it equal to zero to find the stationary points. The numerical values obtained for the second derivatives at these stationary points, decides whether there is a maximum or a minimum at these points., , REVIEW QUESTIONS, 1. What are the drawbacks of numerical differentiation?, Solution Numerical differentiation has two main drawbacks. (i) On the right hand, side of the approximation to f ′(x), we have the multiplying factor 1/h, and on the right, hand side of the approximation to f ″(x), we have the multiplying factor 1/h2. Since h is, small, this implies that we may be multiplying by a large number. For example, if, h = 0.01, the multiplying factor on the right hand side of the approximation to f ′(x) is, 100, while the multiplying factor on the right hand side of the approximation to f ″(x) is, 10000. Therefore, the round-off errors in the values of f(x) and hence in the forward, differences, when multiplied by these multiplying factors may seriously effect the solution and the numerical process may become unstable. (ii) When a data is given, we do, not know whether it represents a continuous function or a piecewise continuous function. It is possible that the function may not be differentiable at some points in its, domain. If we try to find the derivatives at these points where the function is not differentiable, the result is unpredictable., 2. Given the data (xi, f(xi)), i = 0, 1, 2,…, n at equispaced points xi = x0 + ih where h is the, step length, write the formula to compute f ′(x0), using the Newton’s forward difference, formula., Solution In terms of the forward differences, we have the formula, f ′(x0) =, , LM, N, , OP, Q, , 1, 1, 1, 1, 1, ∆f0 − ∆2 f0 + ∆3 f0 − ∆4 f0 + ∆5 f0 − ... ., 2, 3, 4, 5, h, , 3. Given the data (xi, f(xi)), i = 0, 1, 2,…, n at equispaced points xi = x0 + ih, where h is the, step length, write the formula to compute f ″(x0), using the Newton’s forward difference, formula.
Page 136 :
125, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Solution In terms of the forward differences, we have the formula, f ′′(x0) =, , LM∆ f, N, , 1, h, , 2, , 2, , 0, , − ∆3 f0 +, , OP, Q, , 11 4, 5, 137 6, ∆ f0 − ∆5 f0 +, ∆ f0 − ... ., 12, 6, 180, , 4. Given the data (xi, f(xi)), i = 0, 1, 2,…, n at equispaced points xi = x0 + ih, where h is the, step length, write the formula to compute f ′(xn) using the Newton’s backward difference formula., Solution In terms of the backward differences, we have the formula, f ′(xn) =, , LM, N, , OP, Q, , 1, 1, 1, 1, 1, ∇fn + ∇ 2 fn + ∇ 3 fn + ∇ 4 fn + ∇ 5 fn + ... ., h, 2, 3, 4, 5, , 5. Given the data (xi, f(xi)), i = 0, 1, 2,…, n at equispaced points xi = x0 + ih, where h is the, step length, write the formula to compute f ′(xn–1), using the Newton’s backward difference formula., Solution In terms of the backward differences, we have the formula, f ′(xn–1) =, , LM, N, , OP, Q, , 1, 1, 1, 1 4, 1 5, ∇fn − ∇ 2 fn − ∇3 fn −, ∇ fn −, ∇ fn + ... ., h, 2, 6, 12, 20, , 6. Given the data (xi, f(xi)), i = 0, 1, 2,…, n at equispaced points xi = x0 + ih, where h is, the step length, write the formula to compute f ″(xn), using the Newton’s backward, difference formula., Solution In terms of the backward differences, we have the formula, f ″(xn) =, , 1, h, , 2, , LM∇, N, , 2, , fn + ∇ 3 f n +, , OP, Q, , 11 4, 5, 137 6, ∇ f n + ∇ 5 fn +, ∇ fn + ... ., 12, 6, 180, , 7. What is the error in the following approximation?, , 1, [f(xk+1) – f(xk )]., h, Solution Using the Taylor series expansion of f(xk+1), we get the error of approximation as, f ′(xk) =, , 1, h, [f(xk + h) – f(xk)] = –, f ″(xk) + ..., h, 2, 8. What is the error in the following approximation?, E(f, xk) = f ′(xk) –, , f ′(xk) =, , 1, [– 3 f(xk) + 4f(xk+1) – f(xk+2)]., 2h, , Solution Using the Taylor series expansion of f(xk+1) and f(xk+2), we get the error of, approximation as, E(f, xk) = f ′(xk) –, , h2, 1, f ′′′( x k ) + ..., [– 3 f(xk) + 4f(xk+1) – f(xk+2)] =, 3, 2h
Page 137 :
126, , NUMERICAL METHODS, , EXERCISE 3.1, 1., , The following data gives the velocity of a particle for 20 seconds at an interval of 5, seconds. Find the initial acceleration using the entire data., Time (sec), , 0, , 5, , 10, , 15, , 20, , Velocity (m/sec), , 0, , 3, , 14, , 69, , 228, , (A.U. April/May 2004), 2., , Compute f ′(0) and f ″(4) from the data, x, , 0, , 1, , 2, , 3, , 4, , y, , 1, , 2.718, , 7.381, , 20.086, , 54.598, , (A.U. May 2000), 3., , 4., , Find the maximum and minimum values of y tabulated below., x, , –2, , –1, , 0, , 1, , 2, , 3, , 4, , y, , 1, , – 0.25, , 0, , – 0.25, , 2, , 15.75, , 56, , Find the value of x for which f(x) is maximum in the range of x given, using the following table. Find also the maximum value of f(x)., x, , 9, , 10, , 11, , 12, , 13, , 14, , y, , 1330, , 1340, , 1320, , 1250, , 1120, , 930, , (A.U. Nov./Dec. 2004), 5., , For the given data, x, , 1.0, , 1.1, , 1.2, , 1.3, , 1.4, , 1.5, , 1.6, , y, , 7.989, , 8.403, , 8.781, , 9.129, , 9.451, , 9.750, , 10.031, , find dy/dx, d2y/dx2 at 1.1., 6., , (A.U. Nov./Dec. 2003), , The first derivative at a point xk, is approximated by, f(xk) = [f(xk + h) – f(xk – h)]/(2h)., Find the error term using the Taylor series., , 7., , From the following table, x, , 1.0, , 1.2, , 1.4, , 1.6, , 1.8, , 2.0, , 2.2, , y, , 2.7183, , 3.3201, , 4.0552, , 4.9530, , 6.0496, , 7.3891, , 9.0250, , obtain dy/dx, d2y/dx2 at x = 1.2., , (A.U. Nov./Dec. 2006)
Page 138 :
127, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , 8., , Obtain the value of f ′(0.04) using an approximate formula for the given data, x, , 0.01, , 0.02, , 0.03, , 0.04, , 0.05, , 0.06, , y, , 0.1023, , 0.1047, , 0.1071, , 0.1096, , 0.1122, , 0.1148, , (A.U. Nov./Dec. 2003), , 9., , Find the value of sec 31° for the following data, θ (deg), , 31, , 32, , 33, , 34, , tan θ, , 0.6008, , 0.6249, , 0.6494, , 0.6745, , (A.U. Nov./Dec. 2004), 10., , Find f ′(1) using the following data and the Newton’s forward difference formula., x, f(x), , 11., , 1.0, , 1.5, , 2.0, , 2.5, , 3.0, , – 1.5, , – 2.875, , – 3.5, , – 2.625, , 0.5, , Using the Newton’s forward difference formula, find f ′(1.5) from the following data., x, , 1.0, , 1.5, , 2.0, , 2.5, , f(x), , 3.7183, , 5.4817, , 8.3891, , 13.1825, , Find the magnitude of the actual error, if the data represents the function ex + 1., 12., , Given the following data, find y ′(6), y ′(5) and the maximum value of y., x, , 0, , 2, , 3, , 4, , 7, , 9, , y, , 4, , 26, , 58, , 112, , 466, , 922, , (A.U. May/Jun. 2006), 13., , Given the following data, find y ′(6)., x, , 0, , 2, , 3, , 4, , 7, , 8, , y, , 4, , 26, , 58, , 112, , 466, , 668, , (A.U. Nov./Dec. 2006), 14., , An approximation to f ″(x) is given by, f ″(x) =, , 1, h2, , [f(x + h) – 2f(x) + f(x – h)].
Page 139 :
128, , NUMERICAL METHODS, , Compute f ″(0.3) using this formula with all possible step lengths for the given data., x, , 0.1, , 0.2, , 0.3, , 0.4, , 0.5, , f(x), , 2.3214, , 2.6918, , 3.1221, , 3.6255, , 4.2183, , If the data represents the function f(x) = e2x + x + 1, what are the actual errors? Which, step length has produced better result?, , 3.3, , NUMERICAL INTEGRATION, , 3.3.1 Introduction, The problem of numerical integration is to find an approximate value of the integral, I=, , z, , b, , w(x) f(x) dx, , a, , (3.25), , where w(x) > 0 in (a, b) is called the weight function. The function f(x) may be given explicitly, or as a tabulated data. We assume that w(x) and w(x) f(x) are integrable on [a, b]. The limits of, integration may be finite, semi-infinite or infinite. The integral is approximated by a linear, combination of the values of f(x) at the tabular points as, I=, , z, , b, , a, , n, , ∑, , w(x) f(x) dx =, , k=0, , λk f(xk), , = λ0 f(x0) + λ1 f(x1) + λ2 f(x2) + ... + λn f(xn)., , (3.26), , The tabulated points xk’s are called abscissas, f(xk)’s are called the ordinates and λk’s, are called the weights of the integration rule or quadrature formula (3.26)., We define the error of approximation for a given method as, Rn(f) =, , z, , b, , a, , n, , ∑, , w(x) f(x) dx –, , k=0, , λk f(xk)., , (3.27), , Order of a method An integration method of the form (3.26) is said to be of order p, if it, produces exact results, that is Rn = 0, for all polynomials of degree less than or equal to p. That, is, it produces exact results for f(x) = 1, x, x2, ...., x p. This implies that, Rn(xm) =, , z, , n, , b, , w(x) x m dx –, , a, , k=0, , The error term is obtained for f(x) =, c=, , z, , b, , a, , ∑, , x p+1., , λk xkm = 0, for m = 0, 1, 2, …, p., , We define, n, , w(x), , x p+1, , dx –, , ∑, , k=0, , λk xkp+1, , where c is called the error constant. Then, the error term is given by, , (3.28)
Page 140 :
129, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Rn(f) =, =, , z, , b, , a, , n, , w(x) f(x) dx –, , ∑, , k=0, , λk f(xk), , c, f (p+1) (ξ), a < ξ < b., ( p + 1) !, , (3.29), , The bound for the error term is given by, | Rn (f) | ≤, , |c|, max | f ( p+ 1) ( x) ., a, ( p + 1) ! ≤ x ≤ b, , (3.30), , If Rn(x p+1) also becomes zero, then the error term is obtained for f(x) = x p+2., 3.3.2 Integration Rules Based on Uniform Mesh Spacing, When w(x) = 1 and the nodes xk’s are prescribed and are equispaced with x0 = a, xn = b, where, h = (b – a)/n, the methods (3.26) are called Newton-Cotes integration rules. The weights λk’s, are called Cotes numbers., We shall now derive some Newton-Cotes formulas. That is, we derive formulas of the, form, I=, , We note that,, , z, , z, , b, , a, , n, , f(x) dx =, , ∑, , k=0, , λk f(xk), , = λ0 f(x0) + λ1 f(x1) + λ2 f(x2) + ... + λn f(xn)., b, , a, , (3.31), , f(x) dx defines the area under the curve y = f(x), above the x-axis,, , between the lines x = a, x = b., 3.3.2.1 Trapezium Rule, This rule is also called the trapezoidal rule. Let the curve, y = f(x), a ≤ x ≤ b, be approximated by the line joining the, points P(a, f(a)), Q(b, f(b)) on the curve (see Fig. 3.1)., , y, , O, , 1, (x – x0) ∆f(x0), f(x) = f(x0) +, h, , z, , b, , a, , f ( x) dx =, , a, , b, , x, , (3.32), Fig. 3.1. Trapezium rule., , where x0 = a, x1 = b and h = b – a. Substituting in (3.31),, we obtain, I=, , Q, , P, , Using the Newton’s forward difference formula, the, linear polynomial approximation to f(x), interpolating at, the points P(a, f(a)), Q(b, f(b)), is given by, , z, , x1, , x0, , = (x1 – x0) f(x0) +, , f ( x)dx = f ( x0 ), , LM, N, , 1 1, ( x − x0 ) 2, h 2, , OP, Q, , z, , x1, , x0, , x1, x0, , dx +, , ∆f0, , 1, h, , LM, N, , z, , x1, , x0, , OP, Q, , ( x − x0 ) dx ∆f0
Page 141 :
130, , NUMERICAL METHODS, , = (x1 – x0) f(x0) +, , h, [f(x1) – f(x0)], 2, , = hf(x0) +, , (b − a), h, [f(x1) + f(x0)] =, [f(b) + f(a)]., 2, 2, , =, The trapezium rule is given by, I=, , 1, [f(x1) – f(x0)](x1 – x0)2, 2h, , z, , b, , a, , f(x) dx =, , h, (b − a), [f(x1) + f(x0)] =, [f(b) + f(a)]., 2, 2, , (3.33), , Remark 6 Geometrically, the right hand side of the trapezium rule is the area of the trapezoid with width b – a, and ordinates f(a) and f(b), which is an approximation to the area, under the curve y = f(x) above the x-axis and the ordinates x = a and x = b., Error term in trapezium rule We show that the trapezium rule integrates exactly polynomial of degree, , ≤ 1. That is, using the definition of error given in (3.27), we show that, R1(f, x) = 0 for f(x) = 1, x., , Substituting f(x) = 1, x in (3.27), we get, f(x) = 1:, , R1(f, x) =, , f(x) = x: R1(f, x) =, , z, z, , b, , a, b, , a, , dx –, , (b − a), (2) = (b – a) – (b – a) = 0., 2, , x dx –, , (b − a), 1, 1, (b + a) = (b2 – a2) – (b2 – a2) = 0., 2, 2, 2, , Hence, the trapezium rule integrates exactly polynomial of degree ≤ 1, and the method, is of order 1., Let f(x) = x2. From (3.28), we get, c=, =, , z, , b, , a, , x2 dx –, , (b − a) 2, 1, 1, (b + a2) =, (b – a)3 – (b3 + a2b – ab2 – a3), 2, 3, 2, , 1 3, 1, (a – 3a2b + 3ab2 – b3) = – (b – a)3., 6, 6, , Using (3.29), the expression for the error is given by, R1(f, x) =, , c, (b − a) 3, h3, f ′′ (ξ) = −, f ′′ (ξ), f ″(ξ) = –, 2!, 12, 12, , (3.34), , where a ≤ ξ ≤ b., The bound for the error is given by, | R1 (f, x) | ≤, , (b − a) 3, h3, M2 =, M 2 , where M 2 = max | f ′′( x)|., a≤ x≤b, 12, 12, , (3.35)
Page 142 :
131, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , If the length of the interval [a, b] is large, then b – a is also large and the error expression given (3.35) becomes meaningless. In this case, we subdivide [a, b] into a number of, subintervals of equal length and apply the trapezium rule to evaluate each integral. The rule, is then called the composite trapezium rule., Composite trapezium rule Let the interval [a, b] be subdivided into N equal parts of length h., That is, h = (b – a)/N. The nodal points are given by, a = x0, x1 = x0 + h, x2 = x0 + 2h, ..., xN = x0 + Nh = b., We write, , z, , b, , a, , f ( x ) dx =, , z, , xN, , x0, , f ( x ) dx =, , z, , x1, , x0, , f ( x ) dx +, , z, , x2, , x1, , f ( x ) dx + ... +, , z, , xN, , x N −1, , f ( x )dx ., , There are N integrals. Using the trapezoidal rule to evaluate each integral, we get the, composite trapezoidal rule as, , z, , b, , a, , f ( x) dx =, , =, , h, [{f(x0) + f(x1)} + {f(x1) + f(x2)} + ... + {f(xN–1) + f(xN)}], 2, , h, [f(x0) + 2{f(x1) + f(x2) + ... + f(xN–1)} + f(xN)]., 2, , (3.36), , The composite trapezium rule is also of order 1., The error expression (3.34) becomes, R1(f, x) = –, , h3, [ f ′′( ξ1 ) + f ′′( ξ 2 ) + ... + f ′′( ξ N )],, 12, , x N −1 < ξ N < x N ., , (3.37), , The bound on the error is given by, | R1(f, x) | ≤, ≤, or, where, , | R1(f, x) | ≤, , h3, [| f ′′(ξ 1 )|+| f ′′(ξ 2 )|+ ... +| f ′′(ξ N )|], 12, (b − a)h 2, Nh 3, M2 =, M2, 12, 12, (b − a) 3, 12 N 2, , M2, , M2 = max | f ′′ ( x)|, a≤ x≤b, , (3.38), , and Nh = b – a., , This expression is a true representation of the error in the trapezium rule. As we increase, the number of intervals, the error decrases., Remark 7 Geometrically, the right hand side of the composite trapezium rule is the sum of, areas of the N trapezoids with width h, and ordinates f(xi–1) and f(xi), i = 1, 2, ...., N. This sum, is an approximation to the area under the curve y = f(x) above the x-axis and the ordinates, x = a and x = b.
Page 143 :
132, , NUMERICAL METHODS, , Remark 8 We have noted that the trapezium rule and the composite trapezium rule are of, order 1. This can be verified from the error expressions given in (3.34) and (3.37). If f(x) is a, polynomial of degree ≤ 1, then f ″(x) = 0. This result implies that error is zero and the trapezium rule produces exact results for polynomials of degree ≤ 1., Example 3.11 Derive the trapezium rule using the Lagrange linear interpolating polynomial., Solution The points on the curve are P(a, f(a)), Q(b, f(b)) (see Fig. 3.1). Lagrange linear interpolation gives, f(x) =, , =, , ( x − b), ( x − a), f (a) +, f (b), (a − b), (b − a), 1, [{f(b) – f(a)} x + {bf(a) – af(b)}]., (b − a), , Substituting in the integral, we get, I=, , z, , b, , a, , f ( x) dx =, , 1, (b − a), , LM, N, , z, , b, , a, , [{ f (b) − f (a)} x + {bf (a) − af (b)}] dx, , =, , 1, 1, { f (b) − f (a)} (b2 − a2 ) + {bf (a) − af (b)}(b − a), (b − a) 2, , =, , 1, (b + a)[ f(b) – f(a)] + bf(a) – af(b), 2, , =, , (b − a), [f(a) + f(b)], 2, , which is the required trapezium rule., Example 3.12 Find the approximate value of I =, , z, , 1, , 0, , OP, Q, , dx, , using the trapezium rule with 2, 4, 1+ x, , and 8 equal subintervals. Using the exact solution, find the absolute errors., Solution With N = 2, 4 and 8, we have the following step lengths and nodal points., N = 2: h =, , b− a 1, = . The nodes are 0, 0.5, 1.0., N, 2, , N = 4: h =, , b−a 1, = . The nodes are 0, 0.25, 0.5, 0.75, 1.0., N, 4, , N = 8: h =, , b− a 1, = . The nodes are 0, 0.125, 0.25, 0.375, 0.5, 0.675, 0.75, 0.875, 1.0., N, 8
Page 144 :
133, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , We have the following tables of values., N = 2:, , x, , 0, , 0.5, , 1.0, , f(x), , 1.0, , 0.666667, , 0.5, , N = 4: We require the above values. The additional values required are the following:, x, , 0.25, , 0.75, , f (x), , 0.8, , 0.571429, , N = 8: We require the above values. The additional values required are the following:, x, , 0.125, , 0.375, , 0.625, , 0.875, , f (x), , 0.888889, , 0.727273, , 0.615385, , 0.533333, , Now, we compute the value of the integral., N = 2:, , I1 =, , h, [f(0) + 2f(0.5) + f(1.0)], 2, , = 0.25 [1.0 + 2(0.666667) + 0.5] = 0.708334., N = 4:, , I2 =, , h, [f(0) + 2{f(0.25) + f(0.5) + f(0.75)} + f(1.0)], 2, , = 0.125 [1.0 + 2 {0.8 + 0.666667 + 0.571429} + 0.5] = 0.697024., N = 8:, , I3 =, , h, [f(0) + 2{f(0.125) + f(0.25) + f(0.375) + f(0.5), 2, + f(0.625) + f(0.75) + f(0.875)} + f(1.0)], , = 0.0625[1.0 + 2{0.888889 + 0.8 + 0.727273 + 0.666667 + 0.615385, + 0.571429 + 0.533333} + 0.5] = 0.694122., The exact value of the integral is I = ln 2 = 0.693147., The errors in the solutions are the following:, | Exact – I1 | = | 0.693147 – 0.708334 | = 0.015187, | Exact – I2 | = | 0.693147 – 0.697024 | = 0.003877, | Exact – I3 | = | 0.693147 – 0.694122 | = 0.000975., Example 3.13 Evaluate I =, , z, , 2, , 1, , dx, with 4 and 8 subintervals using the trapezium rule., 5 + 3x, , Compare with the exact solution and find the absolute errors in the solutions. Comment on the, magnitudes of the errors obtained. Find the bound on the errors., Solution With N = 4 and 8, we have the following step lengths and nodal points., N = 4:, , h=, , b−a 1, = . The nodes are 1, 1.25, 1.5, 1.75, 2.0., N, 4
Page 145 :
134, , NUMERICAL METHODS, , N = 8:, , h=, , b− a 1, = . The nodes are 1, 1.125, 1.25, 1.375, 1.5, 1.675, 1.75, 1.875, 2.0., N, 8, , We have the following tables of values., N = 4:, , x, , 1.0, , 1.25, , 1.5, , 1.75, , 2.0, , f (x), , 0.125, , 0.11429, , 0.10526, , 0.09756, , 0.09091, , N = 8: We require the above values. The additional values required are the following., x, , 1.125, , 1.375, , 1.625, , 1.875, , f(x), , 0.11940, , 0.10959, , 0.10127, , 0.09412, , Now, we compute the value of the integral., I1 =, , N = 4:, , h, [f(1) + 2 {f(1.25) + f(1.5) + f(1.75)} + f(2.0)], 2, , = 0.125 [0.125 + 2 {0.11429 + 0.10526 + 0.09756} + 0.09091], = 0.10627., N = 8:, , I2 =, , h, [f(1) + 2{f(1.125) + f(1.25) + f(1.375) + f(1.5), 2, + f(1.625) + f(1.75) + f(1.875)} + f(2.0)], , = 0.0625 [0.125 + 2{0.11940 + 0.11429 + 0.10959 + 0.10526 + 0.10127, + 0.09756 + 0.09412} + 0.09091], = 0.10618., The exact value of the integral is, , LM, N, , OP, Q, , 1, ln (5 + 3x ), I=, 3, , 2, , 1, , =, , 1, [ln 11 − ln 8] = 010615, ., ., 3, , The errors in the solutions are the following:, | Exact – I1 | = | 0.10615 – 0.10627 | = 0.00012., | Exact – I2 | = | 0.10615 – 0.10618 | = 0.00003., We find that, , | Error in I2 | ≈, , 1, | Error in I1 |., 4, , Bounds for the errors, | Error | ≤, We have, , f(x) =, , (b − a) h 2, M2 , where M2 = max | f ″(x) |., [1, 2 ], 12, 1, 3, 18, , f ′( x) = −, , f ′′( x) =, ., 2, 5 + 3x, (5 + 3 x), (5 + 3 x) 3
Page 146 :
135, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , M2 = max, [ 1, 2 ], , 18, 18, =, = 0.03516., 512, (5 + 3 x) 3, , h = 0.25: | Error | ≤, , (0.25) 2, (0.03516) = 0.00018., 12, (0.125) 2, (0.03516) = 0.000046., 12, , h = 0.125: | Error | ≤, , Actual errors are smaller than the bounds on the errors., , z, , dx, , 1, , , with 2 and, x + 6x + 10, 4 subintervals. Compare with the exact solution. Comment on the magnitudes of the errors, obtained., , Example 3.14 Using the trapezium rule, evaluate the integral I =, , 0, , 2, , Solution With N = 2 and 4, we have the following step lengths and nodal points., N = 2:, , h = 0.5. The nodes are 0.0, 0.5, 1.0., , N = 4:, , h = 0.25. The nodes are 0.0, 0.25, 0.5, 0.75, 1.0., , We have the following tables of values., N = 2:, , x, , 0.0, , 0.5, , 1.0, , f (x), , 0.1, , 0.07547, , 0.05882, , N = 4: We require the above values. The additional values required are the following., x, , 0.25, , 0.75, , f (x), , 0.08649, , 0.06639, , Now, we compute the value of the integral., N = 2:, , I1 =, , h, [f(0.0) + 2 f(0.5) + f(1.0)], 2, , = 0.25 [0.1 + 2(0.07547) + 0.05882] = 0.07744., N = 4:, , I2 =, , h, [f(0.0) + 2{f(0.25) + f(0.5) + f(0.75)} + f(1.0)], 2, , = 0.125[0.1 + 2(0.08649 + 0.07547 + 0.06639) + 0.05882] = 0.07694., The exact value of the integral is, I=, , z, , 1, , 0, , dx, ( x + 3), , 2, , L, = M tan, + 1 MN, , O, ( x + 3)P, PQ, , 1, , −1, , = tan −1 ( 4 ) − tan −1 (3) = 0.07677 ., 0, , The errors in the solutions are the following:, | Exact – I1 | = | 0.07677 – 0.07744 | = 0.00067, | Exact – I2 | = | 0.07677 – 0.07694 | = 0.00017.
Page 147 :
136, , NUMERICAL METHODS, , We find that, , 1, | Error in I1 |., 4, , | Error in I2 | ≈, , Example 3.15 The velocity of a particle which starts from rest is given by the following table., t (sec), , 0, , 2, , 4, , 6, , 8, , 10, , 12, , 14, , 16, , 18, , 20, , v (ft/sec), , 0, , 16, , 29, , 40, , 46, , 51, , 32, , 18, , 8, , 3, , 0, , Evaluate using trapezium rule, the total distance travelled in 20 seconds., Solution From the definition, we have, , ds, , or s =, dt, , v=, , z, , v dt., , Starting from rest, the distance travelled in 20 seconds is, s=, , z, , 20, , 0, , v dt., , The step length is h = 2. Using the trapezium rule, we obtain, , h, [f(0) + 2{f(2) + f(4) + f(6) + f(8) + f(10) + f(12) + f(14), 2, , s=, , + f(16) + f(18)} + f(20)], = 0 + 2{16 + 29 + 40 + 46 + 51 + 32 + 18 + 8 + 3} + 0 = 486 feet., 3.3.2.2 Simpson’s 1/3 Rule, In the previous section, we have shown that the trapezium rule of integration integrates exactly, polynomials of degree ≤ 1, that is, the order of the formula is 1. In many science and engineering, applications, we require methods which produce more accurate results. One such method is, the Simpson’s 1/3 rule., Let the interval [a, b] be subdivided into two equal parts with step length h = (b – a)/2., We have three abscissas x0 = a, x1 = (a + b)/2, and x2 = b., Then, P(x0, f(x0)), Q(x1 f(x1)), R(x2, f(x2)) are three points on the curve y = f(x). We, approximate the curve y = f(x), a ≤ x ≤ b, by the parabola joining the points P, Q, R, that is, we, approximate the given curve by a polynomial of degree 2. Using the Newton’s forward difference, formula, the quadratic polynomial approximation to f(x), interpolating at the points, P(x0, f(x0)), Q(x1 f(x1)), R(x2, f(x2)), is given by, f(x) = f(x0) +, Substituting in (3.31), we obtain, , z, , b, , a, , f ( x) dx =, , z, , x2, , x0, , f ( x) dx =, , z, , x2, , x0, , 1, 1, ( x − x0 ) ∆ f ( x0 ) +, ( x − x0 )( x − x1 ) ∆2 f ( x0 ) ., h, 2 h2, , LM f (x ) + 1 (x − x ) ∆f (x ) + 1, h, 2h, N, 0, , 0, , 0, , 2, , OP, Q, , ( x − x0 )( x − x1 ) ∆2 f ( x0 ) dx
Page 149 :
138, , NUMERICAL METHODS, , Let [(x – x0)/h] = s. The limits of integration become:, for x = x0, s = 0, and for x = x2, s = 2., We have dx = h ds. Hence,, , z, , x2, , x0, , z LMN, 2, , f ( x) dx = h, , 0, , f ( x0 ) + s∆f ( x0 ) +, , OP, Q, , 1, s( s − 1) ∆2 f ( x0 ) ds, 2, , L, O, 1Fs, s, s I, ∆f ( x ) + G, ∆ f ( x )P, −, = h Ms f ( x ) +, J, 2, 2H 3, 2K, MN, PQ, 1, L, O, = h M2f ( x ) + 2∆ f ( x ) + ∆ f ( x )P, 3, N, Q, 2, , 3, , 0, , 2, , 0, , 0, , 2, , 0, , 2, , 2, , 0, , 0, , 0, , =, , h, [6f(x0) + 6{f(x1) – f(x0)} + {f(x0) – 2f(x1) + f(x2)}], 3, , =, , h, [f(x0) + 4f(x1) + f(x2)], 3, , which is the same formula as derived earlier., Error term in Simpson 1/3 rule. We show that the Simpson’s rule integrates exactly polynomials of degree ≤ 3. That is, using the definition of error given in (3.27), we show that, R2(f, x) = 0 for f(x) = 1, x, x2, x3., Substituting f(x) = 1, x, x2, x3 in (3.27), we get, f(x) = 1:, , R2(f, x) =, , f(x) = x:, , R2(f, x) =, =, , f(x) = x2: R2(f, x) =, , z, z, , b, , dx −, , a, b, , (b − a), (6) = (b – a) – (b – a) = 0., 6, , x dx −, , a, , LM, N, , IJ OP, K Q, , FG, H, , (b − a), a+b, +b, a+4, 6, 2, , 1 2, 1 2, (b – a2) –, (b – a2) = 0., 2, 2, , z, , b, , a, , x 2 dx −, , LM, MN, , FG, H, , a+b, (b − a) 2, a +4, 6, 2, , IJ, K, , 2, , =, , 1 3, (b − a) 2, (b − a3 ) −, [ a + ab + b2 ], 3, 3, , =, , 1 3, 1, (b − a3 ) − (b3 − a3 ) = 0., 3, 3, , f(x) = x3: R2(f, x) =, , z, , b, , a, , x 3 dx −, , LM, MN, , FG, H, , a+b, (b − a) 3, a +4, 6, 2, , IJ, K, , 3, , + b2, , OP, PQ, , + b3, , OP, PQ
Page 150 :
139, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , =, , 1 4, (b − a) 3, (b – a4) –, [a + a2b + ab2 + b3], 4, 4, , =, , 1 4, 1 4, (b – a4) –, (b – a4) = 0., 4, 4, , Hence, the Simpson’s rule integrates exactly polynomials of degree ≤ 3. Therefore, the, method is of order 3. It is interesting to note that the method is one order higher than expected,, since we have approximated f(x) by a polynomial of degree 2 only., Let f(x) = x4. From (3.28), we get, c=, , z, , b, , a, , x 4 dx −, , LM, MN, , FG, H, , a+b, (b − a) 4, a +4, 6, 2, , IJ, K, , 4, , + b4, , OP, PQ, , =, , 1 5, (b − a), (b – a5) –, (5a4 + 4a3b + 6a2b2 + 4ab3 + 5b4), 5, 24, , =, , 1, [24(b5 – a5) – 5(b – a)(5a4 + 4a3b + 6a2b2 + 4ab3 + 5b4)], 120, , =–, , (b − a) 4, [b – 4ab3 + 6a2b2 – 4a3b + a4)], 120, , =–, , (b − a) 5, ., 120, , Using (3.29), the expression for the error is given by, R(f, x) =, , (b − a )5 ( 4 ), c (4), h5 ( 4 ), (ξ) = −, (ξ) = −, f, f, f (ξ), 4!, 2880, 90, , (3.41), , since h = (b – a)/2, and a ≤ ξ ≤ b., Since the method produces exact results, that is, R2(f, x) = 0, when f(x) is a polynomial, of degree ≤ 3, the method is of order 3., The bound for the error is given by, | R(f, x) | ≤, , (b − a )5, h5, (4 ), M4 =, M 4 , where M4 = max | f ( x)|., a≤x≤b, 2880, 90, , (3.42), , As in the case of the trapezium rule, if the length of the interval [a, b] is large, then, b – a is also large and the error expression given in (3.41) becomes meaningless. In this case,, we subdivide [a, b] into a number of subintervals of equal length and apply the Simpson’s 1/3, rule to evaluate each integral. The rule is then called the composite Simpson’s 1/3 rule., Composite Simpson’s 1/3 rule We note that the Simpson’s rule derived earlier uses three, nodal points. Hence, we subdivide the given interval [a, b] into even number of subintervals of, equal length h. That is, we obtain an odd number of nodal points. We take the even number of, intervals as 2N. The step length is given by h = (b – a)/(2N). The nodal points are given by
Page 151 :
140, , NUMERICAL METHODS, , a = x0, x1 = x0 + h, x2 = x0 + 2h, ..., x2N = x0 + 2N h = b., The given interval is now written as, , z, , b, , a, , f ( x ) dx =, , z, , x2N, , x0, , f ( x ) dx =, , z, , x2, , x0, , f ( x ) dx +, , z, , x4, , x2, , f ( x ) dx + ... +, , z, , x 2N, , x 2N −2, , f ( x ) dx., , Note that there are N integrals. The limits of each integral contain three nodal points., Using the Simpson’s 1/3 rule to evaluate each integral, we get the composite Simpson’s 1/3, rule as, , z, , b, , a, , f ( x) dx =, , h, [{f(x0) + 4f(x1) + f(x2)} + {f(x2) + 4 f(x3) + f(x4)} + ..., 3, , + {f(x2N–2) + 4f(x2N–1) + f(x2N)}], =, , h, [f(x0) + 4{f(x1) + f(x3) + ...+ f(x2N–1)} + 2{f(x2) + f(x4) + ..., 3, + f(x2N–2)} + f(x2N)], , (3.43), , The composite Simpson’s 1/3 rule is also of order 3., The error expression (3.34) becomes, R(f, x) = –, where, , h 5 ( 4), [ f (ξ 1 ) + f (4) (ξ 2 ) + ... + f ( 4) (ξ N )] ,, 90, , (3.44), , x0, < ξ1 < x2, x2 < ξ2 < x4, etc., , The bound on the error is given by, | R(f, x) | ≤, , ≤, , or, where, , | R(f, x) | ≤, , h5, | f (4) (ξ 1 )|+ | f ( 4) (ξ 2 )|+ ... + | f ( 4) (ξ N )|, 90, Nh 5, (b − a) h 4, M4 =, M4, 90, 180, (b − a) 5, 2880 N 4, , (3.45), , M4, , M4 = max | f ( 4) ( x) | and N h = ( b – a)/2., a≤ x≤b, , This expression is a true representation of the error in the Simpson’s 1/3 rule. We observe, that as N increases, the error decreases., Remark 9 We have noted that the Simpson 1/3 rule and the composite Simpson’s 1/3 rule are, of order 3. This can be verified from the error expressions given in (3.41) and (3.45). If f(x) is a, polynomial of degree ≤ 3, then f (4) (x) = 0. This result implies that error is zero and the composite, Simpson’s 1/3 rule produces exact results for polynomials of degree ≤ 3.
Page 152 :
141, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Remark 10 Note that the number of subintervals is 2N. We can also say that the number of, subintervals is n = 2N and write h = (b – a)/n, where n is even., Example 3.16 Find the approximate value of I =, , z, , 1, , 0, , dx, , using the Simpson’s 1/3 rule with, 1+ x, , 2, 4 and 8 equal subintervals. Using the exact solution, find the absolute errors., Solution With n = 2N = 2, 4 and 8, or N = 1, 2, 4 we have the following step lengths and nodal, points., N = 1:, , h=, , b−a 1, = . The nodes are 0, 0.5, 1.0., 2N, 2, , N = 2:, , h=, , b−a 1, = . The nodes are 0, 0.25, 0.5, 0.75, 1.0., 2N, 4, , N = 4:, , h=, , b−a 1, = . The nodes are 0, 0.125, 0.25, 0.375, 0.5, 0.625, 0.75, 0.875, 1.0., 2N, 8, , We have the following tables of values., n = 2N = 2:, , x, , 0, , 0.5, , 1.0, , f (x), , 1.0, , 0.666667, , 0.5, , n = 2N = 4: We require the above values. The additional values required are the following., x, , 0.25, , 0.75, , f(x), , 0.8, , 0.571429, , n = 2N = 8: We require the above values. The additional values required are the following., x, , 0.125, , 0.375, , 0.625, , 0.875, , f(x), , 0.888889, , 0.727273, , 0.615385, , 0.533333, , Now, we compute the value of the integral., n = 2N = 2:, , I1 =, =, , n = 2N = 4:, , I2 =, =, , n = 2N = 8:, , I3 =, , h, [f(0) + 4f(0.5) + f(1.0)], 3, 1, [1.0 + 4(0.666667) + 0.5] = 0.674444., 6, h, [f(0) + 4{f(0.25) + f(0.75)} + 2f(0.5) + f(1.0)], 3, 1, [1.0 + 4 {0.8 + 0.571429} + 2(0.666667) + 0.5] = 0.693254., 12, h, [f(0) + 4{f(0.125) + f(0.375) + f(0.625) + f(0.875)}, 3, + 2{f(0.25) + f(0.5) + f(0.75)} + f(1.0)]
Page 153 :
142, , NUMERICAL METHODS, , =, , 1, [1.0 + 4 {0.888889 + 0.727273 + 0.615385 + 0.533333}, 24, + 2 {0.8 + 0.666667 + 0.571429} + 0.5], , = 0.693155., The exact value of the integral is I = ln 2 = 0.693147., The errors in the solutions are the following:, | Exact – I1 | = | 0.693147 – 0.694444 | = 0.001297., | Exact – I2 | = | 0.693147 – 0.693254 | = 0.000107., | Exact – I3 | = | 0.693147 – 0.693155 | = 0.000008., Example 3.17 Evaluate I =, , z, , 2, , 1, , dx, , using the Simpson’s 1/3 rule with 4 and 8 subintervals., 5 + 3x, , Compare with the exact solution and find the absolute errors in the solutions., Solution With N = 2N = 4, 8 or N = 2, 4, we have the following step lengths and nodal points., N = 2:, , h=, , b−a 1, = . The nodes are 1, 1.25, 1.5, 1.75, 2.0., 2N, 4, , N = 4:, , h=, , b−a 1, = . The nodes are 1, 1.125, 1.25, 1.375, 1.5, 1.675, 1.75, 1.875, 2.0., 2N, 8, , We have the following tables of values., n = 2N = 4:, , x, , 1.0, , 1.25, , 1.5, , 1.75, , 2.0, , f (x), , 0.125, , 0.11429, , 0.10526, , 0.09756, , 0.09091, , n = 2N = 8: We require the above values. The additional values required are the following., x, , 1.125, , 1.375, , 1.625, , 1.875, , f(x), , 0.11940, , 0.10959, , 0.10127, , 0.09412, , Now, we compute the value of the integral., n = 2N = 4:, , I1 =, =, , h, [f(1) + 4{(1.25) + f(1.75)} + 2f(1.5) + f(2.0)], 3, 0.25, [0.125 + 4{0.11429 + 0.09756} + 2(0.10526) + 0.09091], 3, , = 0.10615., n = 2N = 8:, , I2 =, , h, [f(1) + 4{f(1.125) + f(1.375) + f(1.625) + f(1.875)}, 3, + 2{f(1.25) + f(1.5) + f(1.75)} + f(2.0)]
Page 154 :
143, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , =, , 0.125, [0.125 + 4{0.11940 + 0.10959 + 0.10127 + 0.09412}, 3, + 2{0.11429 + 0.10526 + 0.09756} + 0.09091], , = 0.10615., The exact value of the integral is I =, , 1, [ln 11 – ln 8] = 0.10615., 3, , The results obtained with n = 2N = 4 and n = 2N = 8 are accurate to all the places., Example 3.18 Using Simpson’s 1/3 rule, evaluate the integral I =, 4 subintervals. Compare with the exact solution., , z, , dx, , 1, , 0, , 2, , x + 6x + 10, , , with 2 and, , Solution With n = 2N = 2 and 4, or N = 1, 2, we have the following step lengths and nodal, points., N = 1:, , h = 0.5. The nodes are 0.0, 0.5, 1.0., , N = 2:, , h = 0.25. The nodes are 0.0, 0.25, 0.5, 0.75, 1.0., , We have the following values of the integrand., n = 2N = 2:, , x, , 0.0, , 0.5, , 1.0, , f (x), , 0.1, , 0.07547, , 0.05882, , n = 2N = 4: We require the above values. The additional values required are the following., x, , 0.25, , 0.75, , f(x), , 0.08649, , 0.06639, , Now, we compute the value of the integral., n = 2N = 2:, , I1 =, =, , n = 2N = 4:, , I2 =, =, , h, [f(0.0) + 4 f(0.5) + f(1.0)], 3, 0.5, [0.1 + 4(0.07547) + 0.05882] = 0.07678., 3, h, [f(0.0) + 4 {f(0.25) + f(0.75)} + 2 f(0.5) + f(1.0)], 3, 0.25, [0.1 + 4(0.08649 + 0.06639) + 2(0.07547) + 0.05882] = 0.07677., 3, , The exact value of the integral is, , I=, , z, , 1, , 0, , LM, MN, , OP, PQ, , dx, = tan −1 ( x + 3), 2, ( x + 3) + 1, , 1, , = tan −1 ( 4 ) − tan −1 (3) = 0.07677 ., 0
Page 155 :
144, , NUMERICAL METHODS, , The errors in the solutions are the following:, | Exact – I1 | = | 0.07677 – 0.07678 | = 0.00001., | Exact – I2 | = | 0.07677 – 0.07677 | = 0.00000., Example 3.19 The velocity of a particle which starts from rest is given by the following table., t (sec), , 0, , 2, , 4, , 6, , 8, , 10, , 12, , 14, , 16, , 18, , 20, , v (ft/sec), , 0, , 16, , 29, , 40, , 46, , 51, , 32, , 18, , 8, , 3, , 0, , Evaluate using Simpson’s 1/3 rule, the total distance travelled in 20 seconds., Solution From the definition, we have, v=, , ds, , or s =, dt, , z, , v dt., , Starting from rest, the distance travelled in 20 seconds is, s=, , z, , 20, , 0, , v dt., , The step length is h = 2. Using the Simpson’s rule, we obtain, s=, , h, [f(0) + 4{f(2) + f(6) + f(10) + f(14) + f(18)} + 2{f(4) + f(8), 3, + f(12) + f(16)} + f(20)], , =, , 2, [0 + 4{16 + 40 + 51 + 18 + 3} + 2{29 + 46 + 32 + 8} + 0], 3, , = 494.667 feet., 3.3.2.3 Simpson’s 3/8 Rule, To derive the Simpson’s 1/3 rule, we have approximated f(x) by a quadratic polynomial. To, derive the Simpson’s 3/8 rule, we approximate f(x) by a cubic polynomial. For interpolating by, a cubic polynomial, we require four nodal points. Hence, we subdivide the given interval [a, b], into 3 equal parts so that we obtain four nodal points. Let h = (b – a)/3. The nodal points are, given by, x0 = a, x1 = x0 + h, x2 = x0 + 2h, x3 = x0 + 3h., Using the Newton’s forward difference formula, the cubic polynomial approximation to, f(x), interpolating at the points, P(x0, f(x0)), Q(x1, f(x1)), R(x2, f(x2)), S(x3, f(x3)), is given by
Page 157 :
146, , NUMERICAL METHODS, , If f(x) is a polynomial of degree ≤ 3, then f (4) (x) = 0. This result implies that error, expression given in (3.47) or (3.48) is zero and the composite Simpson’s 3/8 rule produces exact, results for polynomials of degree ≤ 3. Therefore, the formula is of order 3, which is same as the, order of the Simpson’s 1/3 rule., Remark 11 In Simpson’s 3/8th rule, the number of subintervals is n = 3N. Hence, we have, h=, , b− a, b−a, , or h =, 3N, n, , where n is a multiple of 3., Remark 12 Simpson’s 3/8 rule has some disadvantages. They are the following: (i) The number, of subintervals must be divisible by 3. (ii) It is of the same order as the Simpson’s 1/3 rule,, which only requires that the number of nodal points must be odd. (iii) The error constant c in, the case of Simpson’s 3/8 rule is c = 3/80, which is much larger than the error constant c = 1/90,, in the case of Simpson’s 1/3 rule. Therefore, the error in the case of the Simpson’s 3/8 rule is, larger than the error in the case Simpson 1/3 rule. Due to these disadvantages, Simpson’s 3/8, rule is not used in practice., Example 3.20 Using the Simpson’s 3/8 rule, evaluate I =, Compare with the exact solution., , z, , 2, , 1, , dx, with 3 and 6 subintervals., 5 + 3x, , Solution With n = 3N = 3 and 6, we have the following step lengths and nodal points., n = 3N = 3:, , h=, , b−a 1, = . The nodes are 1, 4/3, 5/3, 2.0., 3N, 3, , n = 3N = 6:, , h=, , b−a 1, = . The nodes are 1, 7/6, 8/6, 9/6, 10/6, 11/6, 2.0, 3N, 6, , We have the following tables of values., n = 3N = 3:, , x, , 1.0, , 4/3, , 5/3, , 2.0, , f (x), , 0.125, , 0.11111, , 0.10000, , 0.09091, , n = 3N = 6: We require the above values. The additional values required are the following., x, , 7/6, , 9/6, , 11/6, , f(x), , 0.11765, , 0.10526, , 0.09524, , Now, we compute the value of the integral., n = 3N = 3:, , I1 =, , 3h, [f(1) + 3 f(4/3) + 3 f(5/3) + f(2.0)], 8, , = 0.125[0.125 + 3{0.11111 + 0.10000} + 0.09091] = 0.10616., n = 3N = 6:, , I2 =, , 3h, [f(1) + 3{f(7/6) + f(8/6) + f(10/6) + f(11/6)}, 8, + 2 f(9/6)} + f(2.0)]
Page 158 :
147, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , =, , 1, [0.125 + 3 {0.11765 + 0.11111 + 0.10000 + 0.09524}, 16, + 2(0.10526) + 0.09091] = 0.10615., , The exact value of the integral is I =, , 1, [log 11 – log 8] = 0.10615., 3, , The magnitude of the error for n = 3 is 0.00001 and for n = 6 the result is correct to all, places., 3.3.2.4 Romberg Method (Integration), In order to obtain accurate results, we compute the integrals by trapezium or Simpson’s rules, for a number of values of step lengths, each time reducing the step length. We stop the computation, when convergence is attained (usually, the magnitude of the difference in successive, values of the integrals obtained by reducing values of the step lengths is less than a given, accuracy). Convergence may be obtained after computing the value of the integral with a number, of step lengths. While computing the value of the integral with a particular step length, the, values of the integral obtained earlier by using larger step lengths were not used. Further,, convergence may be slow., Romberg method is a powerful tool which uses the method of extrapolation., We compute the value of the integral with a number of step lengths using the same, method. Usually, we start with a coarse step length, then reduce the step lengths and recompute the value of the integral. The sequence of these values converges to the exact value of, the integral. Romberg method uses these values of the integral obtained with various step, lengths, to refine the solution such that the new values are of higher order. That is, as if the, results are obtained using a higher order method than the order of the method used. The, extrapolation method is derived by studying the error of the method that is being used., Let us derive the Romberg method for the trapezium and Simpson’s rules., Romberg method for the trapezium rule, Let the integral, I=, , z, , b, , a, , f ( x) dx, , be computed by the composite trapezium rule. Let I denote the exact value of the integral, and I T denote the value obtained by the composite trapezium rule., The error, I – IT , in the composite trapezium rule in computing the integral is given by, I – IT = c1h2 + c2h4 + c3h6 + ..., or, , I = IT + c1h2 + c2h4 + c3h6 + ..., , (3.49), , where c1, c2, c3, ... are independent of h., To illustrate the extrapolation procedure, first consider two error terms., I = IT + c1h2 + c2h4., , (3.50)
Page 159 :
148, , NUMERICAL METHODS, , Let I be evaluated using two step lengths h and qh, 0 < q < 1. Let these values be, denoted by IT (h) and IT (qh). The error equations become, I = IT(h) + c1h2 + c2h4., , (3.51), , I = IT(qh) + c1q2h2 + c2q4h4., , (3.52), , From (3.51), we obtain, I – IT(h) = c1h2 + c2h4., , (3.53), , From (3.52), we obtain, I – IT (qh) = c1q2h2 + c2q4h4., , (3.54), , Multiply (3.53) by q2 to obtain, q2 [I – IT (h)] = c1q2h2 + c2q2h4., , (3.55), , Eliminating c1q2h2 from (3.54) and (3.55), we obtain, (1 – q2)I – IT (qh) + q2IT(h) = c2q2h4(q2 – 1)., Solving for I, we obtain, I=, , IT (qh) − q 2 IT (h), – c2q2h4., (1 − q 2 ), , Note that the error term on the right hand side is now of order O(h4)., Neglecting the O(h4) error term, we obtain the new approximation to the value of the, integral as, I ≈ IT(1) (h) =, , IT (qh) − q 2 IT (h), ., (1 − q 2 ), , (3.56), , We note that this value is obtained by suitably using the values of the integral obtained, with step lengths h and qh, 0 < q < 1. This computed result is of order, O(h4), which is higher, than the order of the trapezium rule, which is of O(h2)., For q = 1/2, that is, computations are done with step lengths h and h/2, the formula, (3.56) simplifies to, I T(1) ( h ) ≈, , =, , I T ( h/2) − (1/4 ) I T ( h ), 1 − (1/4 ), , 4 I T (h/2) − IT (h ) 4 IT (h/2) − I T (h ), =, ., 4 −1, 3, , (3.57), , In practical applications, we normally use the sequence of step lengths h, h/2, h/22, h/23, ..., Suppose, the integral is computed using the step lengths h, h/2, h/22. Using the results, obtained with the step lengths h/2, h/22, we get
Page 160 :
149, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , IT (h/4) − (1/4) IT (h/2), 1 − (1/4), , IT(1) (h/2) ≈, , 4 IT (h/4) − IT (h/2) 4 IT (h/4) − IT (h/2), =, ., 4−1, 3, , =, , (3.58), , Both the results I T(1) (h), I T(1) (h/2) are of order, O(h4). Now, we can eliminate the O(h4), terms of these two results to obtain a result of next higher order, O(h6). The multiplicative, factor is now (1/2)4 = 1/16. The formula becomes, , IT(2) (h) ≈, , 16 IT( 1) (h/2) − IT( 1) (h) 16 IT(1) (h/2) − IT(1) (h), =, ., 16 − 1, 15, , (3.59), , Therefore, we obtain the Romberg extrapolation procedure for the composite trapezium, rule as, , 4 m IT( m −1) (h/2) − IT( m− 1) (h), ,, 4m − 1, , IT( m) (h) ≈, , m = 1, 2, ..., , (3.60), , IT(0) (h) = IT (h) ., , where, , The computed result is of order O(h2m+2)., The extrapolations using three step lengths h, h/2, h/22, are given in Table 3.1., Table 3.1. Romberg method for trapezium rule., Step, , Value of I, , Value of I, , Value of I, , Length, , O(h2), , O(h4), , O(h6), , h, , I(h), , I (1) (h ) =, , h/2, , I ( 2 ) (h ) =, , I(h/2), , I (1) (h/2) =, h/4, , 4 I ( h/2) − I ( h ), 3, 16I (1) ( h/2) − I (1) (h ), 15, , 4 I (h/4 ) − I ( h/2), 3, , I(h/4), , Note that the most accurate values are the values at the end of each column., Romberg method for the Simpson’s 1/3 rule We can apply the same procedure as in trapezium rule to obtain the Romberg’s extrapolation procedure for the Simpson’s 1/3 rule., Let I denote the exact value of the integral and IS denote the value obtained by the, composite Simpson’s 1/3 rule.
Page 161 :
150, , NUMERICAL METHODS, , The error, I – IS, in the composite Simpson’s 1/3 rule in computing the integral is given by, I – IS = c1h4 + c2h6 + c3h8 + ..., I = IS + c1h4 + c2h6 + c3h8 + ..., , or, , (3.61), , As in the trapezium rule, to illustrate the extrapolation procedure, first consider two, error terms., I = IS + c1h4 + c2h6., , (3.62), , Let I be evaluated using two step lengths h and qh, 0 < q < 1. Let these values be, denoted by IS(h) and IS(qh). The error equations become, I = IS(h) + c1h4 + c2h6., , (3.63), , I = IS(qh) + c1q4h4 + c2q6h6., , (3.64), , From (3.63), we obtain, I – IS(h) = c1h4 + c2h6., , (3.65), , From (3.64), we obtain, I – IS(qh) = c1q4h4 + c2q6h6., , (3.66), , Multiply (3.65) by q4 to obtain, q4[I – IS(h)] = c1q4h4 + c2q4h6., , (3.67), , Eliminating c1q4h4 from (3.66) and (3.67), we obtain, (1 – q4)I – IS(qh) + q4 IS(h) = c2q4h6 (q2 – 1)., Note that the error term on the right hand side is now of order O(h6). Solving for I, we, obtain, I=, , IS (qh) − q 4 IS (h), (1 − q 4 ), , −, , c2 q4, h6., 1 + q2, , Neglecting the O(h6) error term, we obtain the new approximation to the value of the, integral as, I ≈ I S(1) (h) =, , I S (qh) − q 4 I S (h), (1 − q 4 ), , ., , (3.68), , Again, we note that this value is obtained by suitably using the values of the integral, obtained with step lengths h and qh, 0 < q < 1. This computed result is of order, O(h6), which, is higher than the order of the Simpson’s 1/3 rule, which is of O(h4)., For q = 1/2, that is, computations are done with step lengths h and h/2, the formula, (3.68) simplifies to, I S(1) (h) ≈, , I S ( h/2) − (1/16) I S ( h), 1 − (1/16)
Page 162 :
151, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , =, , h/23,, , 16 I S (h/2) − IS (h) 16 IS (h/2) − I S (h), =, ., 16 − 1, 15, , (3.69), , In practical applications, we normally use the sequence of step lengths h, h/2, h/22,, ..., , Suppose, the integral is computed using the step lengths h, h/2, h/22. Using the results, obtained with the step lengths h/2, h/22, we get, , IS (h/4) − (1/16) I S (h/2), 1 − (1/16), , I S(1) (h/2) ≈, , 16 I S (h/4) − I S (h/2) 16 IS (h/4) − I S (h/2), ., =, 16 − 1, 15, , =, , (3.70), , Both the results IT(1) (h), IT( 1) (h/2) are of order, O(h6). Now, we can eliminate the O(h6), terms of these two results to obtain a result of next higher order, O(h8). The multiplicative, factor is now (1/2)6 = 1/64. The formula becomes, , I S(2) (h) ≈, , 64 IS(1) (h/2) − IS( 1) (h) 64 I S(1) (h/2) − IS(1) (h), =, ., 64 − 1, 63, , (3.71), , Therefore, we obtain the Romberg extrapolation procedure for the composite Simpson’s, 1/3 rule as, , I S( m) (h) ≈, , 4 m+ 1 I S( m− 1) (h/2) − IS( m −1) (h), 4 m+ 1 − 1, , , m = 1, 2, ..., , (3.72), , I S(0 ) ( h) = IS(h)., , where, , The computed result is of order O(h2m+4)., The extrapolations using three step lengths h, h/2, h/22, are given in Table 3.2., Table 3.2. Romberg method for Simpson’s 1/3 rule., Step, , Value of I, , Value of I, , Value of I, , Length, , O(h4), , O(h6), , O(h8), , h, , I(h), , I (1) (h ) =, h/2, , I(2) (h) =, , I(h/2), , I (1) (h/2) =, h/4, , 16I (h/ 2) − I ( h ), 15, , I(h/4), , 16I ( h/ 4 ) − I ( h/2), 15, , 64 I (1) ( h/2) − I (1) (h ), 63
Page 163 :
152, , NUMERICAL METHODS, , Note that the most accurate values are the values at the end of each column., Example 3.21 The approximations to the values of the integrals in Examples 3.12 and 3.13, were obtained using the trapezium rule. Apply the Romberg’s method to improve the, approximations to the values of the integrals., Solution In Example 3.12, the given integral is, I=, , z, , 1, , 0, , dx, 1+ x, , The approximations using the trapezium rule to the integral with various values of the, step lengths were obtained as follows., h = 1/2, N = 2: I = 0.708334; h = 1/4, N = 4: I = 0.697024., h = 1/8, N = 8: I = 0.694122., We have, , I (1) (1/2) =, , 4 I (1/4) − I (1/2) 4(0.697024) − 0.708334, = 0.693254, =, 3, 3, , I (1) (1/4) =, , 4 I (1/8) − I (1/4) 4(0.694122) − 0.697024, =, = 0.693155., 3, 3, , I (2) (1/2) =, , 16 I (1) (1/4) − I (1) (1/2) 16(0.693155) − 0.693254, = 0.693148., =, 15, 15, , The results are tabulated in Table 3.3., Magnitude of the error is, | I – 0.693148 | = | 0.693147 – 0.693148 | = 0.000001., Table 3.3. Romberg method. Example 3.21., Step, , Value of I, , Value of I, , Value of I, , Length, , O(h2), , O(h4), , O(h6), , 1/2, , 0.708334, , 1/4, , 0.697024, , 0.693254, 0.693148, 0.693155, 1/8, , 0.694122, , In Example 3.13, the given integral is, I=, , z, , 2, , 1, , dx, ., 5 + 3x, , The approximations using the trapezium rule to the integral with various values of the, step lengths were obtained as follows., h = 1/4, N = 4: I = 0.10627; h = 1/8, N = 8: I = 0.10618.
Page 164 :
153, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , We have I (1) (1/4 ) =, , 4 I (1/8) − I (1/4 ) 4( 010618, ., ) − 010627, ., = 0.10615., =, 3, 3, , Since the exact value is I = 0.10615, the result is correct to all places., Example 3.22 The approximation to the value of the integral in Examples 3.16 was obtained, using the Simpson’s 1/3 rule. Apply the Romberg’s method to improve the approximation to the, value of the integral., Solution In Example 3.16, the given integral is, I=, , z, , 1, , 0, , dx, ., 1+ x, , The approximations using the Simpson’s 1/3 rule to the integral with various values of, the step lengths were obtained as follows., h = 1/2, n = 2N = 2: I = 0.694444; h = 1/4, n = 2N = 4: I = 693254;, h = 1/8, n = 2N = 8: I = 693155., We have, , I (1) (1/2) =, , 16 I (1/4) − I (1/2) 16 (0.693254) − 0.694444, = 0.693175, =, 15, 15, , I (1) (1/4) =, , 16 I (1/8) − I (1/4) 16 (0.693155) − 0.693254, =, = 0.693148, 15, 15, , I ( 2 ) (1/2) =, , 64 I (1) (1/4 ) − I (1) (1/2) 64( 0.693148) − 0.693175, = 0.693148., =, 63, 63, , The results are tabulated in Table 3.4., Magnitude of the error is, | I – 0.693148 | = | 0.693147 – 0.693148 | = 0.000001., Table 3.4. Romberg method. Example 3.22., Step, , Value of I, , Value of I, , Value of I, , Length, , O(h4), , O(h6), , O(h8), , 1/2, , 0.694444, 0.693175, , 1/4, , 0.693254, , 1/8, , 0.693155, , 0.693148, 0.693148
Page 165 :
154, , NUMERICAL METHODS, , REVIEW QUESTIONS, 1., , What is the order of the trapezium rule for integrating, sion for the error term?, , z, , b, , a, , f ( x ) dx ? What is the expres-, , Solution The order of the trapezium rule is 1. The expression for the error term is, Error = –, 2., , ( b − a )3, h3, f ′′( ξ ) = −, f ′′( ξ ),, 12, 12, , When does the trapezium rule for integrating, , z, , b, , a, , where a ≤ ξ ≤ b ., , f ( x) dx gives exact results?, , Solution Trapezium rule gives exact results when f(x) is a polynomial of degree ≤ 1., 3., , What is the restriction in the number of nodal points, required for using the trapezium, rule for integrating, , z, , b, , a, , f ( x) dx ?, , Solution There is no restriction in the number of nodal points, required for using the, trapezium rule., 4., , What is the geometric representation of the trapezium rule for integrating, , z, , b, , a, , f ( x) dx ?, , Solution Geometrically, the right hand side of the trapezium rule is the area of the, trapezoid with width b – a, and ordinates f(a) and f(b), which is an approximation to the, area under the curve y = f(x) above the x-axis and the ordinates x = a, and x = b., 5., , State the composite trapezium rule for integrating, error., , z, , b, , a, , f ( x) dx , and give the bound on the, , Solution The composite trapezium rule is given by, , z, , b, , a, , f ( x)dx =, , h, [f(x0) + 2{f(x1) + f(x2) + ... + f(xn–1)} + f(xn)], 2, , where nh = (b – a ). The bound on the error is given by, | Error | ≤, where, 6., , (b − a) h 2, nh 3, M2 =, M2, 12, 12, , M2 = max | f ′′ ( x)| and nh = b – a., a≤x≤b, , What is the geometric representation of the composite trapezium rule for integrating, , z, , b, , a, , f ( x) dx ?, , Solution Geometrically, the right hand side of the composite trapezium rule is the sum, of areas of the n trapezoids with width h, and ordinates f(xi–1) and f(xi) i = 1, 2, ..., n. This
Page 166 :
155, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , sum is an approximation to the area under the curve y = f(x) above the x-axis and the, ordinates x = a and x = b., 7., , How can you deduce that the trapezium rule and the composite trapezium rule produce, exact results for polynomials of degree less than or equal to 1?, Solution The expression for the error in the trapezium rule is given by, R1(f, x) = –, , h3, f ′′(ξ), 12, , and the expression for the error in the composite trapezium rule is given by, R1(f, x) = –, , h3, [f ″(ξ1) + f ″(ξ2) + ... + f ″(ξn)],, 12, , xn–1 < ξn < ξn., , If f(x) is a polynomial of degree ≤ 1, then f ″(x) = 0. This result implies that error is zero, and the trapezium rule produces exact results for polynomials of degree ≤ 1., 8., , When does the Simpson’s 1/3 rule for integrating, , z, , b, , a, , f ( x)dx gives exact results?, , Solution Simpson’s 1/3 rule gives exact results when f(x) is a polynomial of degree ≤ 3., 9., , What is the restriction in the number of nodal points, required for using the Simpson’s, 1/3 rule for integrating, , z, , b, , a, , f ( x) dx ?, , Solution The number of nodal points must be odd for using the Simpson’s 1/3 rule or, the number of subintervals must be even., 10., , State the composite Simpson’s 1/3 rule for integrating, the error., , z, , b, , a, , f ( x) dx , and give the bound on, , Solution Let n = 2N be the number of subintervals. The composite Simpson’s 1/3 rule, is given by, , z, , b, , a, , f ( x) dx =, , h, [{f(x0) + 4f(x1) + f(x2)} + {f(x2) + 4f(x3) + f(x4)} + ..., 3, + {f(x2N–2) + 4 f(x2N–1) + f(x2N)}], , =, , h, [f(x0) + 4{f(x1) + f(x3) + ... + f(x2N–1)}, 3, + 2{f(x2) + f(x4) + ... + f(x2N–2)} + f(x2N)], , The bound on the error is given by, | R(f, x) | ≤, ≤, , h5, | f (4) (ξ 1 )|+ | f ( 4) (ξ 2 )|+ ... + | f ( 4) (ξ N )|, 90, Nh 5, (b − a) h 4, M4 =, M4, 90, 180
Page 167 :
156, , NUMERICAL METHODS, , where, 11., , (4 ), x0 < ξ1 < x2 , x2 < ξ2 < x4, etc., M4 = max | f ( x)| and N h = (b – a)/2., a≤x≤b, , How can you deduce that the Simpson’s 1/3 rule and the composite Simpson’s 1/3 rule, produce exact results for polynomials of degree less than or equal to 3?, Solution The expression for the error in the Simpson’s 1/3 rule is given by, R(f, x) =, , (b − a) 5 (4), c ( 4), h 5 (4 ), f (ξ ) = −, f (ξ ) = −, f (ξ), 4!, 2880, 90, , where h = (b – a)/2, and a ≤ ξ ≤ b., The expression for the error in the composite Simpson’s 1/3 rule is given by, R(f, x) = –, where, , h 5 (4 ), [ f (ξ 1 ) + f (4) (ξ 2 ) + ... + f (4) (ξ N )], 90, , x0 < ξ1 < x2 , x2 < ξ2 < x4, etc., , If f(x) is a polynomial of degree ≤ 3, then f(4)(x) = 0. This result implies that error is zero, and the Simpson 1/3 rule produces exact results for polynomials of degree ≤ 3., 12., , What is the restriction in the number of nodal points, required for using the Simpson’s, 3/8 rule for integrating, , z, , b, , a, , f ( x)dx ?, , Solution The number of subintervals must be divisible by 3., 13., , What are the disadvantages of the Simpson’s 3/8 rule compared with the Simpson’s 1/3, rule?, Solution The disadvantages are the following: (i) The number of subintervals must be, divisible by 3. (ii) It is of the same order as the Simpson’s 1/3 rule, which only requires, that the number of nodal points must be odd. (iii) The error constant c in the case of, Simpson’s 3/8 rule is c = 3/80, which is much larger than the error constant c = 1/90, in, the case of Simpson’s 1/3 rule. Therefore, the error in the case of the Simpson’s 3/8 rule, is larger than the error in the case Simpson 1/3 rule., , 14., , Explain why we need the Romberg method., Solution In order to obtain accurate results, we compute the integrals by trapezium, or Simpson’s rules for a number of values of step lengths, each time reducing the step, length. We stop the computation, when convergence is attained (usually, the magnitude, of the difference between successive values of the integrals obtained with the reducing, values of the step lengths is less than a given accuracy). Convergence may be obtained, after computing the value of the integral with a number of step lengths. While computing, the value of the integral with a particular step length, the values of the integral obtained, earlier by using larger step lengths were not used. Further, convergence may be slow., Romberg method is a powerful tool which uses the method of extrapolation. Romberg, method uses these computed values of the integrals obtained with various step lengths,, to refine the solution such that the new values are of higher order. That is, as if they are, obtained using a higher order method than the order of the method used.
Page 168 :
157, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , 15., , An integral I is evaluated by the trapezium rule with step lengths h and qh. Write the, Romberg method for improving the accuracy of the value of the integral., Solution Let IT(h), IT(qh) denote the values of the integral evaluated using the step, lengths h and qh. The required Romberg approximation is given by, I ≈ IT(1) (h) =, , 16., , IT (qh) − q2 IT (h), ., (1 − q2 ), , An integral I is evaluated by the composite trapezium rule with step lengths h, h/2, h/, 22, ..., h/2m, ... . Write the Romberg method for improving the accuracy of the value of, the integral., Solution The required Romberg approximation is given by, , IT( m) (h) ≈, , I T(0) ( h) = IT (h)., , where, 17., , 4 m IT( m− 1) (h/2) − IT( m− 1) (h), , m = 1, 2, ..., 4m − 1, , An integral I is evaluated by the Simpson’s 1/3 rule with step lengths h and qh. Write, the Romberg method for improving the accuracy of the value of the integral., Solution Let IS(h), IS(qh) denote the values of the integral evaluated using the step, lengths h and qh. The required Romberg approximation is given by, I ≈ I S(1) (h) =, , 18., , I S (qh) − q 4 I S (h), (1 − q4 ), , ., , An integral I is evaluated by the composite Simpson’s 1/3 rule with step lengths h, h/2,, h/22, ..., h/2m, ... . Write the Romberg method for improving the accuracy of the value of, the integral., Solution The required Romberg approximation is given by, , I S( m) (h) ≈, , 4 m+ 1 I S( m− 1) (h/2) − IS( m −1) (h), 4 m+ 1 − 1, , , m = 1, 2, ..., , I S(0 ) ( h) = IS(h), m = 1, 2, ..., , where, , EXERCISE 3.2, 1., , 2., , Evaluate, , z, , 1, , 1/2, , dx, by trapezium rule, dividing the range into four equal parts., x, , Using the trapezium rule, find, , z, , (A.U. May/June 2006), 6, , 0, , f ( x) dx , from the following set of values of x and f(x)., , x, , 0, , 1, , 2, , 3, , 4, , 5, , 6, , f (x), , 1.56, , 3.64, , 4.62, , 5.12, , 7.05, , 9.22, , 10.44
Page 169 :
158, 3., , NUMERICAL METHODS, , z, , Using the trapezium rule, evaluate, intervals., , z, , π, , 0, , 6, , sin x dx by dividing the range into 6 equal, , (A.U. Nov./Dec. 2004), , sin x dx with h = 0.5., , 4., , Using the trapezium rule, evaluate, , 5., , The velocity of a particle which starts from rest is given by the following table., , 1, , t (sec), , 0, , 2, , 4, , 6, , 8, , 10, , 12, , 14, , 16, , 18, , v (ft/sec), , 0, , 12, , 16, , 26, , 40, , 44, , 25, , 12, , 5, , 0, , Evaluate using trapezium rule, the total distance travelled in 18 seconds., , z, , 1, , dx, , −1, , 1 + x2, , 6., , Using the trapezium rule, evaluate, , 7., , Using the Simpson’s 1/3 rule, evaluate, result with actual value., , 8., , Evaluate, , z, z, , 2, , 0, , z, , 1, , 0, , taking 8 intervals. (A.U. April/May 2004), , x e x dx taking four intervals. Compare the, , e x dx using the Simpson’s rule with h = 1 and h = 1/2. Compare with exact, , solution. Improve the result using Romberg integration., 9., 10., , Evaluate, , dx, , 6, , 1 + x2, actual integration., 0, , by (i) trapezium rule, (ii) Simpson’s rule. Also, check the result by, (A.U. Nov./Dec. 2004), , Compute, Ip =, , z, , 1, , 0, , xp, dx for p = 0, 1, x + 10, 3, , using trapezium rule and Simpson’s 1/3 rule with the number of points 3, 5 and 9., Improve the results using Romberg integration., 11., , For the given data, x, , 0.7, , 0.9, , 1.1, , 1.3, , 1.5, , 1.7, , 1.9, , 2.1, , f (x), , 0.64835, , 0.91360, , 1.16092, , 1.36178, , 1.49500, , 1.35007, , 1.52882, , 1.44573, , use Simpson’s 1/3 rule for first six intervals and trapezium rule for the last interval to, evaluate, , z, , 2.1, , 0.7, , f ( x) dx . Also, use trapezium rule for the first interval and Simpson’s 1/3, , rule for the rest of intervals to evaluate, , z, , 2.1, , 0.7, , f ( x) dx . Comment on the obtained results, , by comparing with the exact value of the integral, which is equal to 1.81759., (A.U. April/May 2003)
Page 170 :
159, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , 12., , 13., , Evaluate, , z, , 5, , 0, , dx, by Simpson’s 1/3 rule and hence find the value of loge 5, (n = 10)., 4x + 5, , By dividing the range into ten equal parts, evaluate, , z, , (A.U. April/May 2005), π, , 0, , sin x dx by trapezium rule and, , Simpson’s rule. Verify your answer with integration., (A.U. May/June 2006 ; A.U. Nov./Dec. 2006), 14., , z, , Using Simpson’s 3/8th rule, evaluate, parts., , 1, , dx, , 0, , 1 + x2, , by dividing the range into six equal, (A.U. Nov./Dec. 2004), , 3.3.3 Integration Rules Based on Non-uniform Mesh Spacing, We have defined the general integration rule as, I=, , z, , b, , a, , n, , w( x) f ( x) dx =, , ∑λ, , k, , f ( xk ), , k=0, , = λ0 f(x0) + λ1 f(x1) + λ2 f(x2) + ... + λn f(xn)., , (3.73), , When the abscissas are prescribed and are equispaced, that is, xi = x0 + ih, i = 1, 2,…, n,, we have derived the trapezium and Simpson’s rules (Newton-Cotes formulas). When the, abscissa are not prescribed in advance and they are also to be determined, then the formulas, using less number of abscissas can produce higher order methods compared to the NewtonCotes formulas. Such formulas are called Gaussian integration rules or formulas., Gaussian integration rules can be obtained when the limits are finite or one of the, limits is infinite or both the limits are infinite., We have the following Gaussian integration rules depending on the limits of integration and on the expression for the weight function w(x)., 1., , Gauss-Legendre integration rules, Limits of integration = [– 1, 1]. Weight function = w(x) = 1., Abscissas = Zeros of the corresponding Legendre polynomial., , 2., , Gauss-Chebychev integration rules, Limits of integration = [– 1, 1]. Weight function = w(x) = 1/ 1 − x 2 ., Abscissas = Zeros of the corresponding Chebychev polynomial., , 3., , Gauss-Laguerre integration rules, Limits of integration = [0, ∞]. Weight function = w(x) = e–x., Abscissas = Zeros of the corresponding Laguerre polynomial., , 4., , Gauss-Hermite integration rules, 2, , Limits of integration = (– ∞, ∞). Weight function = w(x) = e − x . Abscissas = Zeros of the, corresponding Hermite polynomial.
Page 171 :
160, , NUMERICAL METHODS, , For our discussion and derivation, we shall consider only the Gauss-Legendre integration rules. As per the terminology used in syllabus, we shall call these formulas as Gaussian, formulas., 3.3.3.1 Gauss-Legendre Integration Rules, Since the weight function is w(x) = 1, we shall write the integration rule as, I=, , z, , b, , a, , f ( x) dx = λ0 f(x0) + λ1 f(x1) + λ2 f(x2) + ... + λn f(xn)., , (3.74), , As mentioned earlier, the limits of integration for Gauss-Legendre integration rules, are [– 1, 1]. Therefore, we transform the limits [a, b] to [– 1, 1], using a linear transformation., Let the transformation be, , x = pt + q., , When x = a, we have t = – 1: a = – p + q., When x = b, we have t = 1:, Solving, we get, , b = p + q., , p(b – a)/2, q = (b + a)/2., , The required transformation is, Then,, , x=, , 1, [(b – a)t + (b + a)]., 2, , (3.75), , f(x) = f{[(b – a)t + (b + a)]/2} and dx = [(b – a)/2]dt., , The integral becomes, I=, , z, , b, , a, , where, , z, , RS 1 [(b − a)t + (b + a)]UV RS 1 (b − a)UV dt =, T2, W T2, W, U R1, U, R1, g(t) = S (b − a) V f S [(b − a)t + (b + a)]V ., 2, 2, W T, W, T, f ( x) dx =, , 1, , −1, , f, , Therefore, we shall derive formulas to evaluate, , z, , 1, , −1, , z, , 1, , −1, , −1, , g (t) dt, , (3.76), , g(t) dt ., , Without loss of generality, let us write this integral as, The required integration formula is of the form, , z, , 1, , z, , 1, , −1, , f ( x) dx ., , f ( x) dx = λ0 f(x0) + λ1 f(x1) + λ2 f(x2) + ... + λn f(xn)., , (3.77), , We shall follow the approach of method of undetermined coefficients to derive the, formulas., Before deriving the methods, let us remember the definition of the order of a method, and the expression for the error of the method., An integration method of the form (3.77) is said to be of order p, if it produces exact, results, that is error Rn = 0, for all polynomials of degree less than or equal to p. That is, it, produces exact results for f(x) = 1, x, x2, ..., x p. When w(x) = 1, this implies that
Page 172 :
161, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , z, , Rn(xm) =, , 1, , n, , x m dx −, , −1, , ∑λ, , k, , x km = 0 , for m = 0, 1, 2, …, p., , k=0, , The error term is obtained for f(x) = x p+1. We define, , z, , c=, , 1, , −1, , x p +1 dx −, , n, , ∑λ, , k, , xkp+ 1, , (3.78), , k=0, , where c is called the error constant. Then, the error term is given by, , z, , Rn(f) =, , n, , 1, , f ( x ) dx −, , −1, , =, , ∑λ, , k, , f (xk ), , k=0, , c, f ( p + 1) (ξ),, ( p + 1) !, , a<ξ<b, , (3.79), , If Rn(x p+1) also becomes zero, then the error term is obtained for f(x) = x p+2., Gauss one point rule (Gauss-Legendre one point rule), The one point rule is given by, , z, , 1, , −1, , f ( x)dx = λ0 f(x0), , (3.80), , where λ0 ≠ 0. The method has two unknowns λ0, x0. Making the formula exact for f(x) = 1, x, we, get, f(x) = 1:, f(x) = x:, Since, λ0 ≠ 0, we get x0 = 0., , z, z, , 1, , −1, 1, , −1, , dx = 2 = λ0., xdx = 0 = λ0 x0., , Therefore, the one point Gauss formula is given by, , z, , 1, , −1, , f ( x)dx = 2 f(0)., , (3.81), , Error of approximation, The error term is obtained when f(x) = x2. We obtain, c=, The error term is given by., R(f ) =, , z, , 1, , −1, , x2 dx – 0 =, , 2, ., 3, , c, 1, f ′′(ξ) = f ′′(ξ),, 2!, 3, , − 1 < ξ < 1., , (3.82)
Page 174 :
163, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Error of approximation, The error term is obtained when f(x) = x4. We obtain, c=, , z, , 1, , −1, , The error term is given by, R(f) =, , x 4 dx −, , LM 1 + 1 OP = 2 − 2 = 8 ., N 9 9 Q 5 9 45, , c ( 4), 1 (4 ), f (ξ) =, f (ξ),, 4!, 135, , − 1 < ξ < 1., , (3.89), , Remark 14 Since the error term contains f (4)(ξ), Gauss two point rule integrates exactly, polynomials of degree less than or equal to 3. Therefore, the results obtained from this rule, are comparable with the results obtained from the Simpson’s rule. However, we require three, function evaluations in the Simpson’s rule whereas we need only two function evaluations in, the Gauss two point rule. If better accuracy is required, then the original interval [a, b] can be, subdivided and the limits of each subinterval can be transformed to [– 1, 1]. Gauss two point, rule can then be applied to each of the integrals., Gauss three point rule (Gauss-Legendre three point rule), The three point rule is given by, , z, , 1, , −1, , f ( x)dx = λ0 f(x0) + λ1 f(x1) + λ2 f(x2), , (3.90), , where λ0 ≠ 0, λ1 ≠ 0, λ2 ≠ 0, and x0 ≠ x1 ≠ x2. The method has six unknowns λ0, x0, λ1, x1, λ2, x2., Making the formula exact for f(x) = 1, x, x2, x3, x4, x5, we get, , z, , f(x) = 1:, f(x) = x:, f(x) = x2:, f(x) = x3:, f(x) = x4:, f(x) = x5:, , z, , z, , 1, , −1, , 1, , −1, , 1, , −1, , z, z, z, , dx = 2 = λ0 + λ1 + λ2., , x dx = 0 = λ0x0 + λ1x1 + λ2x2., , x2 dx =, , 1, , −1, , 1, , −1, 1, , −1, , (3.91), , 2, = λ 0 x02 + λ 1 x12 + λ 2 x22 ., 3, , (3.92), (3.93), , x 3 dx = 0 = λ 0 x03 + λ 1 x13 + λ 2 x23 ., , (3.94), , 2, = λ 0 x04 + λ 1 x14 + λ 2 x24 ., 5, , (3.95), , x 5 dx = 0 = λ 0 x05 + λ 1 x15 + λ 2 x25 ., , (3.96), , x 4 dx =, , Solving this system as in the two point rule, we obtain, x0 = ±, , 3, , x 1 = 0, x 2 = +, 5, , 3, 5, 8, , λ 0 = λ 2 = , λ1 = ., 5, 9, 9
Page 175 :
164, , NUMERICAL METHODS, , Therefore, the three point Gauss rule (Gauss-Legendre rule) is given by, , z, , 1, , −1, , f ( x)dx =, , LM F, MN GH, , F 3 I OP., GH 5 JK PQ, , I, JK, , 1, 5f −, 9, , 3, + 8 f (0) + 5 f, 5, , (3.97), , Error of approximation, The error term is obtained when f(x) = x6. We obtain, , z, , LM F, MN GH, , 1, 5 −, x dx −, c=, −1, 9, 1, , 6, , The error term is given by, R(f) =, , 3, 5, , I, JK, , 6, , F 3 I OP = 2 − 6 = 8 ., + 0 + 5G, H 5 JK PQ 7 25 175, 6, , c (6), 8, 1, f (ξ) =, f (6 ) ( ξ ) =, f (6) (ξ),, (6 !) 175, 6!, 15750, , − 1 < ξ < 1., , (3.98), , Remark 15 Since the error term contains f (6)(ξ), Gauss three point rule integrates exactly, polynomials of degree less than or equal to 5. Further, the error coefficient is very small, (1/15750 ≈ 0.00006349). Therefore, the results obtained from this rule are very accurate. We, have not derived any Newton-Cotes rule, which can be compared with the Gauss three point, rule. If better accuracy is required, then the original interval [a, b] can be subdivided and the, limits of each subinterval can be transformed to [– 1, 1]. Gauss three point rule can then be, applied to each of the integrals., Example 3.23 Evaluate the integral I =, , z, , 2, , 1, , 2x, 1 + x4, , dx, using Gauss one point, two point and, , three point rules. Compare with the exact solution I = tan–1 (4) – (π/4)., Solution We reduce the interval [1, 2] to [– 1, 1] to apply the Gauss rules., Writing, , x = a t + b, we get, 1 = – a + b, 2 = a + b., , Solving, we get a = 1/2, b = 3/2. Therefore, x = (t + 3)/2, dx = dt/2., The integral becomes, I=, where, , z, , 8(t + 3), dt =, − 1 [ 16 + (t + 3) 4 ], 1, , f(t) = 8(t + 3)/[16 + (t + 3)4]., , z, , 1, , −1, , f (t) dt, , Using the one point Gauss rule, we obtain, I = 2 f(0) = 2, , LM 24 OP = 48 = 0.494845., N 16 + 81Q 97, , Using the two point Gauss rule, we obtain, I=f, , FG − 1 IJ + f FG 1 IJ = f(– 0.577350) + f(0.577350), H 3K H 3K, , = 0.384183 + 0.159193 = 0.543376.
Page 176 :
165, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Using the three point Gauss rule, we obtain, I=, , The exact values is, , LM F, MN GH, , I, JK, , 1, 3, 5f −, + 8 f (0) + 5 f, 9, 5, , F 3 I OP, GH 5 JK PQ, , =, , 1, [5 f(– 0.774597) + 8 f(0) + 5f(0.774597)], 9, , =, , 1, [5(0.439299) + 8(0.247423) + 5(0.137889) = 0.540592., 9, , I = 0.540420., , The magnitudes of the errors in the one point, two point and three point rules are, 0.045575, 0.002956, and 0.000172 respectively., Example 3.24 Evaluate the integral I =, with the exact solution., , z, , dx, , using the Gauss three point formula. Compare, 1+ x, , 1, , 0, , Solution We reduce the interval [0, 1] to [– 1, 1] to apply the Gauss three point rule., Writing x = a t + b, we get, 0 = – a + b, 1 = a + b, Solving, we get a = 1/2, b = 1/2. Therefore, x = (t + 1)/2, dx = dt/2., The integral becomes, I=, where, , z, , 1, , −1, , dt, =, t+3, , z, , 1, , −1, , f ( t ) dt, , f(t) = 1/(t + 3)., , Using the three point Gauss rule, we obtain, I=, , =, , LM F, MN GH, , I, JK, , 1, 3, 5f −, + 8 f (0) + 5 f, 9, 5, , F 3 I OP, GH 5 JK PQ, , 1, [5(0.449357) + 8(0.333333) + 5(0.264929)] = 0.693122., 9, , The exact solution is I = ln (2) = 0.693147., The absolute error in the three point Gauss rule is 0.000025., Example 3.25 Evaluate the integral I =, , z, , 2, , ( x 2 + 2x + 1), , 0, , 1 + ( x + 1) 4, , dx, by Gauss three point formula., (A.U. April/May 2005), , Solution We reduce the interval [0, 2] to [– 1, 1] to apply the Gauss three point rule.
Page 177 :
166, , NUMERICAL METHODS, , Writing x = a t, , + b, we get, , 0 = – a + b, 2 = a + b., Solving, we get a = 1, b = 1. Therefore, x = t + 1, and dx = dt., The integral becomes, I=, , z, , (t + 2 )2, , 1, , 1 + (t + 2), , −1, , 4, , dt =, , z, , 1, , −1, , f ( t ) dt, , f(t) = (t + 2)2/[1 + (t + 2)4]., , where, , Using the three point Gauss rule, we obtain, I=, , LM F, MN GH, , I, JK, , 1, 3, 5f −, + 8 f (0) + 5 f, 9, 5, , F 3 I OP, GH 5 JK PQ, , 1, [5(0.461347) + 8(0.235194) + 5(0.127742)] = 0.536422., 9, Remark 16 We have derived the Gauss-Legendre rules using the method of undetermined, parameters. However, all the Gaussian rules can be obtained using the orthogonal polynomials., =, , Consider the integration rule (3.73), I=, , z, , b, , a, , w(x) f(x)dx = λ0 f(x0) + λ1 f(x1) + λ2 f(x2) + ... + λn f(xn)., , (3.99), , We state the following theorem which gives these rules., Theorem 3.1 If the abscissas xk of the integration rule are selected as zeros of an orthogonal, polynomial, orthogonal with respect to the weight function w(x) over [a, b], then the formula, (3.99) has precision 2n + 1 (or the formula is exact for polynomials of degree ≤ 2n + 1). Further,, λk > 0., The weights are given by, λk =, , z, , b, , w(x) lk(x)dx, , a, , where lk(x), k = 0, 1, …, n are the Lagrange fundamental polynomials., For deriving the Gauss-Legendre formulas, we have w(x) = 1, [a, b] = [– 1, 1], and the, orthogonal polynomials are the Legendre polynomials Pk(x). The weights are given by, λk =, , z, , 1, , l (x)dx., −1 k, , Gauss-Legendre two point formula, The abscissas x0, x1 are the zeros of the Legendre polynomial P2(x)., Setting P2(x) =, , 1, 1, (3x2 – 1) = 0, we obtain x = ±, ., 2, 3, , (3.100)
Page 178 :
167, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Let x0 = – 1/ 3 , and x1 = 1/ 3 , we have, , x − x1, x − x0, , and l1(x) =, ., x0 − x1, x1 − x0, , l0(x) =, The weights are given by, λ0 =, , z, , 1, , −1, , l0 ( x) dx = 1, λ 1 =, , The two point rule is as given in (3.88)., , z, , 1, , −1, , l1 ( x) dx = 1., , Gauss-Legendre three point formula, The abscissas x0, x1, x2 are the zeros of the Legendre polynomial P3(x)., Setting P3(x) =, Let x0 = –, , 1, (5x3 – 3x) = 0, we obtain x = 0, ±, 2, , 3 / 5 , x1 = 0, and x2 =, , 3 / 5 . We have, , l0(x) =, , ( x − x 1 )( x − x 2 ), ,, ( x 0 − x 1 )( x 0 − x 2 ), , l2(x) =, , ( x − x0 )( x − x1 ), ., ( x2 − x0 )( x2 − x1 ), , The weights are given by, λ0 =, , 3, ., 5, , z, , 1, , −1, , l0 ( x) dx =, , 5, , λ1 =, 9, , The three point rule is as given in (3.97)., , l1 ( x ) =, , z, , 1, , −1, , ( x − x 0 )( x − x 2 ), ,, ( x1 − x 0 )( x1 − x 2 ), , l1 ( x) dx =, , 8, , λ2 =, 9, , z, , 1, , −1, , l2 ( x) dx =, , 5, ., 9, , REVIEW QUESTIONS, 1. Write the error term in the Gauss one point rule for evaluating the integral, Solution The error term in the Gauss one point rule is given by, R(f) =, , 1, f ′′(ξ) ,, 3, , – 1 < ξ < 1., , 2. Write the error term in the Gauss two point rule for evaluating the integral, Solution The error term in the Gauss two point rule is given by, R(f) =, , 1 ( 4), f (ξ) ,, 135, , – 1 < ξ < 1., , z, , 1, , −1, , z, , 1, , −1, , f ( x) dx ., , f ( x) dx.
Page 179 :
168, , NUMERICAL METHODS, , 3. Write the error term in the Gauss three point rule for evaluating the integral, Solution The error term in the Gauss three point rule is given by, R(f ) =, , 1, f (6) (ξ) ,, 15750, , z, , 1, , −1, , f ( x ) dx ., , – 1 < ξ < 1., , EXERCISE 3.3, 1. Use three point Gauss formula to evaluate, , 2. Apply Gauss two point formula to evaluate, , 3. Using three point Gauss formula, evaluate, , 4. Evaluate, , z, , 2, , 0, , z, z, z, , 2, , 1, , dx, ., x, , 1, , dx, , −1, , 1 + x2, , 1, , dx, , 0, , 1 + x2, , z, , 1.5, , 0.2, , ., , (A.U. April/May 2005), , ., , (A.U. April/May 2004), , ( x 2 + 2 x + 1), dx by Gauss three point formula., 1 + ( x + 1) 4, , 5. Using the three point Gauss quadrature, evaluate, , 6. Evaluate, , (A.U. Nov./Dec. 2003), , z, , (A.U. April/May 2005), , 1, , dx, , 0, , 1 + x4, , 2, , e − x dx using the three point Gauss quadrature. (A.U. April/May 2003), , 7. Use two point and three point Gauss formula to evaluate I =, the exact solution., 8. Use two point and three point Gauss formula to evaluate, , 9. Find the value of the integral I =, formulas., , . (A.U. Nov./Dec. 2005), , z, , 10. In problem 7, write I = I1 + I2 =, , z, , z, , 2, , 0, , dx, , 2, , 0, , dx, . Compare with, 3 + 4x, , 2, , x + 2 x + 10, , ., , cos 2 x, dx, using two point and three point Gauss, 1 + sin x, , 3, , 2, , z, , 1, , 0, , f(x) dx +, , z, , 2, , 1, , f(x) dx. Then, evaluate each of the, , integrals by two point and three point Gauss formulas. Compare with the exact solution.
Page 180 :
169, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , 3.3.4 Evaluation of Double Integrals, , (a, d), , (b, c), , (a, c), , (b, c), , We consider the evaluation of the double integral, , z FGH z, d, , b, , c, , a, , IJ, K, , f ( x, y) dx dy, , (3.101), , Fig. 3.2. Region of integration, (a rectangle)., , over a rectangle x = a, x = b, y = c, y = d. (Fig. 3.2)., , 3.3.4.1 Evaluation of Double Integrals Using Trapezium Rule, Evaluating the inner integral in (3.101) by trapezium rule, we obtain, I=, , b− a, 2, , z, , d, , c, , [ f (a, y) + f (b, y)] dy ., , (3.102), , Using the trapezium rule again to evaluate the integrals in (3.102), we obtain, I=, , (b − a)(c − d), [ f (a, c) + f (a, d) + f (b, c) + f (b, d)] ., 4, , Notice that the points (a, c), (a, d), (b, c), (b, d) are, the four corners of the rectangle (Fig. 3.2). If we denote, h = b – a, k = d – c, we can write the formula as, I=, , hk, [f(a, c) + f(a, d) + f(b, c) + f(b, d)]., 4, , (3.104), , (3.103), 1, , 1, , 1, , 1, , hk, ×, 4, , Fig. 3.3. Weights in formula (3.104)., , The weights (coefficients of the ordinates f ) in the trapezium rule are given in the, computational molecule (Fig. 3.3)., Composite trapezium rule Divide the interval [a, b] into N equal subintervals each of length, h, and the interval [c, d] into M equal subintervals each of length k. We have, h=, , b−a, , x0 = a, x1 = x0 + h, x2 = x0 + 2h, ..., xN = x0 + N h = b,, N, , k=, , d−c, , y0 = c, y1 = y0 + k, y2 = y0 + 2k, ..., yM = y0 + M k = d., M, , The general grid point is given by (xi, yj). Denote, fij = f(xi, yj). That is,, f00 = f(x0, y0) = f(a, c), f10 = f(x1, y0), ..., fN0 = f(xN, y0) = f(b, c), ...,, f01 = f(x0, y1), f11 = f(x1, y1), ..., f0M = f(x0, yM) = f(a, d), etc., If we use the composite trapezium rule in both the directions, we obtain, I=, , hk, [f + 2(f01 + f02 + ... + f0M–1) + f0M, 4 00, +2, , N−1, , ∑, , {fi0 + 2(fi1 + fi2 + ... + fiM–1) + fiM}, , i=1, , + fN0 + 2(fN1 + fN2 + ... + fNM–1) + fNM], , (3.105)
Page 181 :
170, , NUMERICAL METHODS, , If M = N = 1, we get the method given in (3.104)., , 1, , For M = N = 2, the weights in the formula are given in, Fig. 3.4., , 1, , Remark 17 The order of the composite trapezium rule is, , 1, 4, , hk, ×2, 4, , For M = N = 4, the weights in the formula are given in, Fig. 3.5., , 1, that is, it integrates exactly polynomials of degree, , 2, , 2, 1, , 2, , Fig. 3.4. Weights in the trapezium, rule (3.105)., , ≤ 1,, , in x and y. If we use the same mesh lengths along x and y directions, that is, h = k, then, Romberg extrapolation can also be used to improve the computed values of the integral. The, Romberg formula is same as given in (3.60)., 2, , 2, , 2, , 1, , 1, , 2, , hk, ×2, 4, , 2, , 4, , 4, , 4, , 4, , 4, , 4, , 4, , 4, , 4, , 2, , 2, , 2, , 1, 2, , 2, , 2, , 1, , Fig. 3.5. Weights in the trapezium rule., , Example 3.26 Evaluate the integral, I=, , zz, 2, , 1, , 2, , 1, , dx dy, x+y, , using the trapezium rule with h = k = 0.5 and h = k = 0.25. Improve the estimate using Romberg, integration. The exact value of the integral is I = ln (1024/729). Find the absolute errors in the, solutions obtained by the trapezium rule and the Romberg value., Solution We have a = 1, b = 2, c = 1, d = 2., When h = k = 0.5, we have the nodes at (1, 1),, (1.5, 1), (2, 1), (1, 1.5), (1.5, 1.5), (2, 1.5), (1, 2),, (1.5, 2), (2, 2). The nodes are given in Fig. 3.6., The values of the integrand at the nodal points, are obtained as the following., , (1.5, 2), (1, 2), , (1, 1.5), , (1.5, 1.5), , (2, 2), , (2, 1.5), , (1, 1), (1.5, 1), , (2, 1), , Fig. 3.6. Nodal points. h = 0.5. Example 3.26.
Page 182 :
171, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , (x, y), , (1, 1), , (1.5, 1), , (2, 1), , (1, 1.5), , (1.5, 1.5), , f (x, y), , 0.5, , 0.4, , 0.333333, , 0.4, , 0.333333, , (x, y), , (2, 1.5), , (1, 2), , (1.5, 2), , (2, 2), , f (x, y), , 0.285714, , 0.333333, , 0.285714, , 0.25, , Using the trapezium rule, we obtain, I=, , hk, [{f(1, 1) + f(2, 1) + f(1, 2) + f(2, 2)} + 2{f(1.5, 1) + f(1, 1.5) + f(2, 1.5), 4, + f(1.5, 2)} + 4 f(1.5, 1.5)], , = 0.0625 [{0.5 + 0.333333 + 0.333333 + 0.25}, + 2{0.4 + 0.4 + 0.285714 + 0.285714} + 4(0.33333)] = 0.343303., With h = 0.25, we have the nodal points as shown in Fig. 3.7., The values at the nodal points are as the following., f(1, 1) = 0.5, f(1, 1.25) = f(1.25, 1) = 0.444444,, f(1.5, 1) = f(1, 1.5) = f(1.25, 1.25) = 0.4,, f(1.75, 1) = f(1, 1.75) = f(1.25, 1.5) = f(1.5, 1.25) = 0.363636,, f(2, 1) = f(1, 2) = f(1.5, 1.5) = f(1.75, 1.25) = f(1.25, 1.75) = 0.333333,, f(2, 1.25) = f(1.25, 2) = f(1.5, 1.75) = f(1.75, 1.5) = 0.307692,, f(1.75, 1.75) = f(2,1.5) = f(1.5, 2) = 0.285714,, f(2, 1.75) = f(1.75, 2) = 0.266667, f(2, 2) = 0.25., (1.25, 2), , (1.5, 2), , (1.75, 2), , (1, 2), , (1, 1.75), , (1, 1.5), , (1, 1.25), , (2, 2), , (1.25, 1.75) (1.5, 1.75) (1.75, 1.75), (2, 1.75), , (1.25, 1.5) (1.5, 1.5) (1.75, 1.5), (2, 1.5), , (1.25, 1.25)(1.5, 1.25) (1.75, 1.25), (2, 1.25), , (1, 1), , (2, 1), (1.25, 1), , (1.5, 1), , (1.75, 1), , Fig. 3.7. Nodal points. h = 0.25. Example 3.26.
Page 183 :
172, , NUMERICAL METHODS, , Using the composite trapezium rule, we obtain, I=, , hk, [{f(1, 1) + f(2, 1) + f(1, 2) + f(2, 2)} + 2{f(1.25, 1) + f(1.5, 1) + f(1.75, 1), 4, + f(1, 1.25) + f(1, 1.5) + f(1, 1.75) + f(2, 1.25) + f(2, 1.5) + f(2, 1.75), + f(1.25, 2) + f(1.5, 2) + f(1.75, 2)} + 4{f(1.25, 1.25) + f(1.25, 1.5), + f(1.25, 1.75) + f(1.5, 1.25) + f(1.5, 1.5) + f(1.5, 1.75) + f(1.75, 1.25), + f(1.75, 1.5) + f(1.75, 1.75)}], , = (0.015625)[{0.5 + 2(0.333333) + 0.25} + 2{2(0.444444) + 2(0.4), + 2(0.363636) + 2(0.307692) + 2(0.285714) + 2(0.266667)}, + 4{0.4 + 2(0.363636) + 3(0.333333) + 2(0.307692) + 0.285714}], = 0.340668., Romberg integration gives the improved value of the integral as, I=, Exact value:, , 1, 1, [4I(0.25) – I(0.5)] =, [4(0.340668) – 0.343303] = 0.339790., 3, 3, , I = ln (1024/729) = 0.339798., , The magnitudes of the errors in the solutions are the following., Trapezium rule with h = k = 0.5:, , | 0.339798 – 0.343303 | = 0.003505., , Trapezium rule with h = k = 0.25:, , | 0.339798 – 0.340668 | = 0.000870, , Romberg value:, , | 0.339798 – 0.339790 | = 0.000008., , Example 3.27 Evaluate, , zz, 2, , 0, , 2, , 0, , f(x, y) dxdy by trapezium rule for the following data., , y/x, , 0, , 0.5, , 1.0, , 1.5, , 2.0, , 0, , 2, , 3, , 4, , 5, , 5, , 1, , 3, , 4, , 6, , 9, , 11, , 2, , 4, , 6, , 8, , 11, , 14, , (A.U. April/May 2005), Solution We have the step lengths along x-axis and y-axis as h = 0.5 and k = 1.0 respectively., Also, the number of intervals along x-axis and y-axis are M = 4 and N = 2. We have the, following grid (Fig. 3.8).
Page 184 :
173, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , (0, 2), , (0.5, 2), , (1, 2), , (1.5, 2), (2, 2), , (0.5, 1), , (0, 1), , (1, 1), , (1.5, 1), (2, 1), , (0, 0), , (0.5, 0), , (1, 0), , (1.5, 0), , (2, 0), , Fig. 3.8. Nodal points, h = 0.5, k = 1.0. Example 3.27., , Using the trapezium rule, we obtain, , hk, [{f(0, 0) + f(2, 0) + f(0, 2) + f(2, 2)} + 2{f(0.5, 0) + f(1, 0), 4, , I=, , + f(1.5, 0) + f(0, 1) + f(2, 1) + f(0.5, 2) + f(1, 2) + f(1.5, 2)}, + 4{f(0.5, 1) + f(1, 1) + f(1.5, 1)}], = (0.125) [{2 + 5 + 4 + 14} + 2{3 + 4 + 5 + 3 + 11 + 6 + 8 + 11}, + 4{4 + 6 + 9}], = 0.125[25 + 2(51) + 4(19)] = 25.375., 3.3.4.2 Evaluation of Double Integrals by Simpson’s Rule, We consider the evaluation of the double integral, , over a rectangle, , z FGH z, d, , b, , c, , a, , IJ, K, , f ( x, y) dx dy, , x = a, x = b, y = c, y = d. (Fig. 3.2)., , To apply the Simpson’s rule, let h = (b – a)/2 and k = (d – c)/2., Evaluating the inner integral by Simpson’s rule, we obtain, I=, where, , h, 3, , z, , d, , c, , [f(a, y) + 4f(a + h, y) + f(b, y)] dy, , (3.106), , a + h = (a + b)/2., , Evaluating the integral again by Simpson’s rule, we obtain, I=, , hk, [{ f(a, c) + 4f(a, c + k) + f(a, d)} + 4{ f(a + h, c) + 4f(a + h, c + k), 9, + f(a + h, d)} + { f(b, c) + 4f(b, c + k) + f(b, d)}]
Page 185 :
174, , NUMERICAL METHODS, , =, , hk, [{f(a, c) + f(a, d) + f(b, c) + f(b, d)} + 4{f(a, c + k), 9, + f(a + h, c) + f(a + h, d) + f(b, c + k)} + 16 f(a + h, c + k)]. (3.107), , The weights (coefficients of the ordinates f ), in the Simpson’s rule are given in the computational, molecule (Fig. 3.9) below., , 4, , 1, , 16, , hk, ×4, 9, , Composite Simpson’s rule, Divide the interval [a, b] into 2N equal parts each, of length h = (b – a)/(2N)., , 1, , 1, , 4, , 4, 1, , Fig. 3.9. Weights in Simpson’s, rule (3.107)., , Divide the interval [c, d] into 2M equal parts each, of length h = (d – c)/(2M)., , We have odd number of points on each mesh line and the total number of points, (2N + 1), (2M + 1) is also odd., The general grid point is given by (xi, yj). Denote, fij = f(xi, yj)., For M = N = 2, the weights in the composite Simpson’s rule are given in Fig. 3.10., 4, , 2, , 4, , 1, , 1, , 4, , 16, , 8, , 16, , 8, , 4, , 8, , 16, , 8, , 16, , hk, ×2, 9, , 4, , 1, , 4, , 2, , 4, , 2, , 4, , 4, , 1, , Fig. 3.10. Weights in the Simpson’s rule., , Example 3.28 Evaluate the integral, I=, , z z, 1.5, , 2, , y =1, , x =1, , dx dy, x+y, , using the Simpson’s rule with h = 0.5 along x-axis and k = 0.25 along y-axis. The exact value of, the integral is I = 0.184401. Find the absolute error in the solution obtained by the Simpson’s, rule.
Page 186 :
175, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , Solution We have a = 1, b = 2, c = 1, d = 1.5. With h, = 0.5, k = 0.25, we have the following nodal points as, given in Fig. 3.11., , (1, 1.5), , (1.5, 1.5), , (2, 1.5), , (1.5, 1.25), , (2, 1.25), , (1, 1.25), , The values at the nodal points are as follows., f(1, 1) = 0.5, f(1, 1.25) = 0.444444,, f(1.5, 1) = f(1, 1.5) = 0.4,, , (1, 1), , f(1.5, 1.25) = 0.363636,, , (1.5, 1), , (2, 1), , Fig. 3.11. Nodal points. Example 3.28., , f(2, 1) = f(1.5, 1.5) = 0.333333,, f(2, 1.25) = 0.307692, f(2, 1.5) = 0.285714., Simpson rule gives the value of the integral as, , hk, [{f(a, c) + f(a, d) + f(b, c) + f(b, d)} + 4{f(a, c + k), 9, , I=, , + f(a + h, c) + f(a + h, d) + f(b, c + k)} + 16f(a + h, c + k)], , 0.125, [{f(1, 1) + f(2, 1) + f(1, 1.5) + f(2, 1.5)} + 4{f(1.5, 1) + f(1, 1.25), 9, , =, , + f(2, 1.25) + f(1.5, 1.5)} + 16 f(1.5, 1.25)], 0.125, [{0.5 + 0.333333 + 0.4 + 0.285714} + 4{0.4 + 0.444444, 9, , =, , + 0.307692 + 0.333333} + 16(0.363636)] = 0.184432., The magnitude of the error in the solution is given by, | 0.184401 – 0.184432 | = 0.000031., Example 3.29 Evaluate, , zz, 1, , 1, , 0, , 0, , e x + y dx dy using Simpson and trapezium rules., , (A.U. May/June 2006 ; A.U. Nov./Dec. 2006), , Solution Since the step lengths are not prescribed, we, use the minimum number of intervals required to use, both the trapezium and Simpson’s rules., , (0, 1), , (0.5, 1), , (0, 0.5), , (0.5, 0.5), , (0, 0), , (0.5, 0), , (1, 1), , (1, 0.5), , Let h = k = 0.5. We have the following grid of points, (Fig. 3.12)., At the nodal points, we have the following values, of the integrand., f(0, 0) =, , e0, , = 1.0, f(0.5, 0) = f(0, 0.5) =, , (1, 0), , Fig. 3.12. Nodal points. Example 3.29., , e0.5, , = 1.648720,, , f(1, 0) = f(0, 1) = f(0.5, 0.5) = e1 = 2.71828,, f(1, 0.5) = f(0.5, 1) = e1.5 = 4.48169, f(1, 1) = e2 = 7.389056.
Page 187 :
176, , NUMERICAL METHODS, , Using the trapezoidal rule, we obtain, I=, , hk, [{f(0, 0) + f(1, 0) + f(0, 1) + f(1, 1)} + 2{f(0.5, 0) + f(0, 0.5) + f(1, 0.5), 4, + f(0.5, 1)} + 4 f(0.5, 0.5)], , = 0.0625[{1.0 + 2(2.71828) + 7.389056} + 2{2(1.64872), + 2(4.48169)} + 4(2.71828)] = 3.07627., Using the Simpson’s rule, we obtain, I=, , hk, [{f(0, 0) + f(1, 0) + f(0, 1) + f(1, 1)} + 4{f(0.5, 0) + f(0, 0.5), 9, + f(0.5, 1.0) + f(1.0, 0.5)} + 16 f(0.5, 0.5)], , =, , 0.25, [{1.0 + 2(2.71828) + 7.389056} + 4{2(1.64872), 9, + 2(4.48169)} + 16(2.71828)] = 2.95448., , L, I = Me, MN, , The exact solution is, , OP, PQ, , 1, , x, , 0, , LMe, MN, , OP, PQ, , 1, , y, , = ( e − 1) 2 = 2.95249 ., 0, , The magnitudes of errors in the solutions are, Trapezium rule: | 3.07627 – 2.95249 | = 0.12378., Simpson’s rule:, , | 2.95448 – 2.95249 | = 0.00199., , EXERCISE 3.4, 1. Using Simpson’s 1/3 rule, evaluate, , 2. Evaluate, , 3. Evaluate, , zz, 1, , 1, , 0, , 0, , z FGH z, 1, , 0, , zz, 1, , 1, , 0, , 0, , dx dy, taking h = k = 0.5., 1+ x + y, , (A.U. April/May 2004), , dx dy, using trapezium rule, taking h = 0.5, k = 0.25., 1+ x + y, (A.U. Nov./Dec. 2006), 2, , 2 xy, , 1, , 2, , 2, , (1 + x )(1 + y ), , I, JK, , dy dx by trapezium rule, taking h = k = 0.25., , (A.U. Nov./Dec. 2004 ; A.U. Nov./Dec. 2005)
Page 188 :
177, , NUMERICAL DIFFERENTIATION AND INTEGRATION, , 4. Evaluate, , zz, 2, , 1, , 2, , 1, , dx dy, x2 + y2, , numerically with h = 0.2 along x-direction and k = 0.25 in the, , y-direction., , zz, zz, 2.0, , 5. Using trapezium rule, evaluate, ∆y = 0.25., 6. Using trapezium rule evaluate,, , 7. Evaluate the double integral, rule with two subintervals., , 1.4, , 2, , 1, , 1.5, , 1, , 8. Evaluate the double integral, , 1.0, , ln ( x + 2 y ) dy dx choosing ∆x = 0.15 and, , (A.U. April/May 2003), , dx dy, taking four sub-intervals., x+y, , 2, , 1, , zz, zz, , 1.5, , (A.U. Nov./Dec. 2003), , dx dy, , 1.5, , ( x + y 2 )1/ 2, , 1, , 2, , 1, , 1, , 0, , 0, , using the trapezium rule and Simpson’s, , dx dy, using the trapezium rule and, ( 3 + x )( 4 + y ), , Simpson’s rule with two and four subintervals., , 3.4, , ANSWERS AND HINTS, , Exercise 3.1, 1. 1.0., , 2. – 0.2225, 52.170833., , 3. y is maximum at s = 2.3792 or x = 0.3792. y(maximum) = 0.0723. y is minimum at, s = 1.1208 or x = – 0.8792. y(minimum) = – 0.2598., 4. y is maximum at s = 1.0546 or x = 10.0546. y(maximum) = 1339.8637. y is minimum at, s = – 2.0546. y(minimum) = 1300.1363., 5. 3.9485, – 3.5894., 6. – (h2/6) f ′″(xk) + ..., or as – (h2/6) f ′″ (ξ), xk – h < ξ < xk + h., 7. 3.3202, 3.3211., , 8. 0.2558., , 9. (dy/dθ) = sec2 θ. For θ = 31°, (dy/dθ) = 0.023967. sec (31°) = 0.1548., 10. – 3., , 11. 4.4235. Magnitude of error = 0.0582., , 12. 135, 98. Since (dy/dx) is always positive, y is an increasing function. The maximum, value is obtained at x = 9. Maximum value = 922., 13. 135., 14. h = 0.2: 7.3875. h = 0.1: 7.31. Exact : 7.2885. Magnitudes of errors are 0.099 and 0.0245, respectively. Error is smaller for h = 0.1.
Page 189 :
178, , NUMERICAL METHODS, , Exercise 3.2, (For comparison, the exact solutions are given, wherever it is necessary)., 1. h = 0.125, 0.697024, , 2. h = 1, 35.65., , 3. h = π/6, 1.954097, Exact : 2.0., 4. h = 0.5, – 0.411059. Exact: cos 1 – cos 6 = – 0.4199., 6. h = 0.25, 1.565588. Exact: 2 tan–1 1 = 570796., , 5. h = 2,360., 7. h = 0.25, 1.000169. Exact : 1., , 8. h = 1: 6.420728, h = 0.5: 6.391210. Romberg value = 6.389242. Exact: 6.389056., 9. h = 3, IT = 1.840541, IS = 1.427027. Exact: tan–1 6 = 1.405648., 10. Trapezium rule: (Romberg table)., p=0, , p=1, , h, , O(h2), , O(h4), , 1/2, , 0.097110, , 1/4, , 0.097504, , 0.097635, , 1/8, , 0.097604, , 0.097637, , O(h6), , O(h2), , h, , 0.097637, , O(h4), , O(h6), , 1/2, , 0.072419, , 1/4, , 0.061305, , 0.057600, , 1/8, , 0.054322, , 0.051994, , 0.051621, , O(h6), , O(h8), , Simpson’s rule: (Romberg table)., p=0, , p=1, , h, , O(h4), , O(h6), , 1/2, , 0.097662, , 1/4, , 0.097635, , 0.097633, , 1/8, , 0.097634, , 0.097634, , O(h8), , 0.097634, , h, , O(h4), , 1/2, , 0.064740, , 1/4, , 0.056448, , 0.055895, , 1/8, , 0.052283, , 0.052005, , 11. 1.76351, 1.79099. The second result is more accurate., 12. h = 0.5, 0.402521, ln (0.5) = 1.610084. Exact: 1.609438., 13. h = π/10, IT = 1.983524, IS = 2.000110. Exact: 2., 14. h = 1/6, 0.785396., Exercise 3.3, (For comparison, the exact solutions are given, wherever it is necessary)., 1. 2x = t + 3, f(t) = 1/(t + 3), 0.693122, 3. 2x = t + 1, f(t) = 2/[4 + (t +, , 1)2],, , 2. 1.5., , 0.785267, , 4. x = t + 1, f(t) = (t + 2)2/[1 + (t + 2)4], 0.586423., 5. 2x = t + 1, f(t) = 2/[16 + (t + 1)4], 0.216880., , 0.051944
Page 190 :
179, , NUMERICAL DIFFERENTIATION AND INTEGRATION, 2, , 6. x = 0.65t + 0.85, f(t) = 0.65 e − (0.65 t + 0.85) , 0.658602., 7. x = t + 1, f(t) = 1/(4t + 7), I(Two point) = 0.320610, I(Three point) = 0.324390., Exact : 0.324821., 8. x = t + 1, f(t) = 1/[9 + (t + 2)2]. I(Two point) = 0.154639. I(Three point) = 0.154548., 9. 2x = t + 5, f(t) = cos (t + 5)/[2(1 + sin {(t + 5)/2}], I(Two point) = 0.407017., I(Three point) = 0.405428., 10. I1 : 2x = t + 1, f(t) = 1/[2/{3 + 2(t + 1)}], I : 2x = t + 3, f(t) = 1/[2{3 + 2(t + 3)}],, Two point formula: I1 = 0.211268, I2 = 0.112971, I = 0.324239., Three point formula: I1 = 0.211799, I2 = 0.112996, I = 0.324795. Exact: 0.324821., Results are more accurate than in Problem 7., Exercise 3.4, 1. 9 points. 0.524074., , 2. 15 points. 0.531953., , 3. 25 points. 0.312330., , 4. 30 points. 0.232316., , 5. 15 points. 0.428875., , 6. 25 points. 0.340668., , 7. 9 points. IT = 0.142157, IS = 0.141900., 8. Two subintervals: IT = 0.064554, IS = 0.064199., Four subintervals: IT = 0.064285, IS = 0.064195.
Page 191 :
", Initial Value Problems For, Ordinary Differential Equations, , 4.1, , INTRODUCTION, , The general form of an mth order ordinary differential equation is given by, φ(x, y, y′, y″, ..., y(m)) = 0., , (4.1), , The order of a differential equation is the order of its highest order derivative and the, degree is the degree of the highest order derivative after the equation has been rationalized, in derivatives. A linear differential equation of order m can be written as, a0(x) y(m) (x) + a1(x) y(m–1)(x) + ... + am–1(x) y′(x) + am(x) y(x) = r(x), , (4.2), , where a0(x), a1(x), ..., am (x) and r(x) are constants or continuous functions of x., The general solution of the equations (4.1) or (4.2) contains m arbitrary constants. The, solution may be obtained in an implicit form as, g(x, y, c1, c2, ..., cm ) = 0,, , (4.3), , or in an explicit form as, y = h(x, c1, c2, ..., cm ), , (4.4), , The m arbitrary constants c1, c2, ..., cm can be determined by prescribing m conditions of, the form, y(x0) = b0, y′(x0) = b1, y″(x0) = b2, ..., y(m–1) (x0) = bm–1., , (4.5), , The conditions are prescribed at one point x0. This point x0 is called the initial point and, the conditions (4.5) are called initial conditions. The differential equation (4.1) or (4.2) together with the initial conditions (4.5) is called an initial value problem., A first order initial value problem can be written as, y′ = f (x, y),, , y(x0) = b0, , 180, , (4.6)
Page 192 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 181, , Reduction of second order equation to a first order system, Let the second order initial value problem be given as, a0(x) y″(x) + a1(x) y′(x) + a2(x) y(x) = r(x),, y(x0) = b0, y′(x0) = b1, , (4.7), , We can reduce this second order initial value problem to a system of two first order, equations., Define u1 = y. Then, we have the system, u1′ = y′ = u2, u1(x0) = b0,, 1, [r(x) – a1(x) y′(x) – a2(x) y(x)], a0 ( x ), , u2′ = y″ =, =, , 1, [r(x) – a1(x) u2 – a2(x) u1], u2(x0) = b1., a0 ( x), , The system is given by, , LMu OP′ = LMu, OP , LMu ( x ) OP = LMb OP, (, ,, ,, ), u, f, x, u, u, N Q N, Q Nu ( x )Q Nb Q, 1, , 2, , 2, , where, , 2, , f2(x, u1, u2) =, , 1, , 2, , 1, , 0, , 0, , 2, , 0, , 1, , (4.8), , 1, [r(x) – a1(x) u2 – a2(x) u1]., a0 ( x), , In general, we may have a system as, , LMy OP′ = LMf ( x , y , y ) OP , LM yy ( xx ) OP = LMbb OP ., N y Q N f ( x , y , y )Q N ( ) Q N Q, 1, , 1, , 1, , 2, , 1, , 0, , 0, , 2, , 2, , 1, , 2, , 2, , 0, , 1, , (4.9), , In vector notation, denote, y = [y1, y2]T, f = [f1, f2]T, b = [b0, b1]T., Then, we can write the system as, y′ = f(x, y),, y(x0) = b., , (4.10), , Therefore, the methods derived for the solution of the first order initial value problem, , dy, = f(x, y), y(x0) = y0, dx, , (4.11), , can be used to solve the system of equations (4.9) or (4.10), that is, the second order initial, value problem (4.7), by writing the method in vector form., Example 4.1 Reduce the following second order initial value problems into systems of first, order equations:, (i) 2y″ – 5y′ + 6y = 3x,, (ii), , x2y″, , + (2x + 1)y′ + 3y = 6,, , y(0) = 1, y′(0) = 2., y(1) = 2, y′(1) = 0.5.
Page 193 :
182, , NUMERICAL METHODS, , Solution, (i) Let u1 = y. Then, we have the system, u1′ = u2, u2′ =, , u1(0) = 1,, , 1, 1, [3 x + 5 y ′ − 6 y] = [3 x + 5u2 − 6u1 ],, 2, 2, , u2 (0) = 2., , The system may be written as, , LMu OP′ = LMf ( x , u , u ) OP , LMu ( 0) OP = LM1 OP, Nu Q Nf ( x , u , u )Q Nu (0)Q N2Q, where, , 1, , 1, , 1, , 2, , 1, , 2, , 2, , 1, , 2, , 2, , f1(x, u1, u2) = u2 and f2(x, u1, u2) = [3x + 5u2 – 6u1]/2., , (ii) Let u1 = y. Then, we have the system, u1′ = u2,, u2′ =, , 1, x, , 2, , u1(1) = 2,, [6 − (2 x + 1) y ′ − 3 y] =, , 1, x2, , [6 − (2 x + 1)u2 − 3u1 ],, , u2 (1) = 0.5 ., , The system may be written as, , LMu OP′ = LMf ( x , u , u ) OP , LMu (1) OP = LM2 OP, Nu Q Nf ( x , u , u )Q Nu (1)Q N0.5Q, where, , 1, , 1, , 1, , 2, , 1, , 2, , 2, , 1, , 2, , 2, , f1(x, u1, u2) = u2 and, , f2(x, u1, u2) = [6 – (2x + 1)u2 – 3u1]/x2., , We assume the existence and uniqueness of solutions of the problems that we are considering., Numerical methods We divide the interval [x0, b] on which the solution is desired, into a, finite number of subintervals by the points, x0 < x1 < x2 < ... < xn = b., The points are called mesh points or grid points. The spacing between the points is, given by, hi = xi – xi–1, i = 1, 2, ..., n., , (4.12), , If the spacing is uniform, then hi = h = constant, i = 1, 2, ..., n., For our discussions, we shall consider the case of uniform mesh only., , 4.2, , SINGLE STEP AND MULTI STEP METHODS, , The methods for the solution of the initial value problem, y′ = f(x, y),, , y(x0) = y0, , (4.13), , can be classified mainly into two types. They are (i) single step methods, and (ii) multi step, methods.
Page 194 :
183, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , We denote the numerical solution and the exact solution at xi by yi and y(xi) respectively., Single step methods In single step methods, the solution at any point xi+1 is obtained using, the solution at only the previous point xi. Thus, a general single step method can be written as, yi+1 = yi + h φ(xi+1, xi, yi+1, yi, h), , (4.14), , where φ is a function of the arguments xi+1, xi, yi+1, yi, h and depends on the right hand side, f(x, y) of the given differential equation. This function φ is called the increment function., If yi+1 can be obtained simply by evaluating the right hand side of (4.14), then the method, is called an explicit method. In this case, the method is of the form, yi+1 = yi + h φ(xi, yi, h)., , (4.15), , That is, we compute successively, y1 = y0 + h φ(x0, y0, h), y2 = y1 + h φ(x1, y1, h), ...., If the right hand side of (4.14) depends on yi+1 also, then it is called an implicit method,, that is, we obtain a nonlinear algebraic equation for the solution of yi+1 (if the differential, equation is nonlinear)., Local truncation error or discretization error The exact solution y(xi) satisfies the equation, y(xi+1) = y(xi) + h φ(xi+1, xi, y(xi+1), y(xi), h) + Ti+1, , (4.16), , where Ti+1 is called the local truncation error or discretization error. Therefore, the Truncation error (T.E.) is defined by, Ti+1 = y(xi+1) – y(xi) – h φ(xi+1, xi, y(xi+1), y(xi), h )., , (4.17), , Order of a method The order of a method is the largest integer p for which, , 1, Ti + 1 = O(h p ) ., h, , (4.18), , Multi step methods In multi step methods, the solution at any point xi+1 is obtained using, the solution at a number of previous points. Suppose that we use y(x) and y′(x) at k + 1 previous, points xi+1 , xi, xi–1, ..., xi–k+1. That is, the values, yi+1, yi, yi–1, ..., yi–k+1, y′i+1, yi′, y′i–1,..., y′i–k+1, are used to determine the approximation to y(x) at xi+1. We assume that the numerical solution is being obtained at xi+1 and the solution values at all the required previous points are, known. We call the method as a k-step multi step method., For example, a two step method uses the values yi+1, yi, yi–1, y′i+1, yi′, y′i–1 and the method, can be written as, yi+1 = yi + h φ(xi+1 , xi, xi–1, yi+1, yi, yi–1, h), or as, , yi+1 = yi–1 + h φ(xi+1 , xi, xi–1, yi+1, yi, yi–1, h),
Page 195 :
184, , NUMERICAL METHODS, , where φ depends on the right hand side f(x, y) of the given differential equation. This function, φ is called the increment function., If yi+1 can be obtained simply by evaluating the right hand side, then the method is, called an explicit method. In this case, the two step method is of the form, yi+1 = yi + hφ(xi, xi–1, yi, yi–1, h), or as, , yi+1 = yi–1 + hφ(xi, xi–1, yi, yi–1, h)., , If the right hand side depends on yi+1 also, then it is called an implicit method, that is,, we obtain a nonlinear algebraic equation for the solution of yi+1 (if the differential equation is, nonlinear)., A general k-step explicit method can be written as, yi+1 = yi + hφ(xi–k+1, ..., xi–1, xi, yi–k+1, ..., yi–1, yi, h), and a general k-step implicit method can be written as, yi+1 = yi + hφ(xi–k+1, ..., xi, xi+1, yi–k+1, ..., yi, yi+1, h)., We now derive a few numerical methods., , 4.3, , TAYLOR SERIES METHOD, , Taylor series method is the fundamental numerical method for the solution of the initial value, problem given in (4.13)., Expanding y(x) in Taylor series about any point, , xi , with the Lagrange form of remain-, , der, we obtain, y(x) = y(xi) + (x – xi) y′(xi) +, +, , 1, 1, (x – xi)2 y″(xi) + ... +, (x – xi) p y (p) (xi), p!, 2!, , 1, ( x − xi ) p+ 1 y( p+ 1) ( xi + θh), ( p + 1) !, , (4.19), , where 0 < θ < 1, x ∈ [x0, b] and b is the point up to which the solution is required., tively., , We denote the numerical solution and the exact solution at xi by yi and y(xi) respec-, , Now, consider the interval [xi, xi+1]. The length of the interval is h = xi+1 – xi., Substituting x = xi+1 in (4.19), we obtain, y(xi+1) = y(xi) + h y′(xi) +, , h2, h p ( p), h p+ 1, y′′( xi ) + ... +, y ( xi ) +, y ( p +1) ( xi + θh) ., 2!, ( p + 1) !, p!
Page 196 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 185, , Neglecting the error term, we obtain the Taylor series method as, yi+1 = yi + hyi′ +, , h2, h p ( p), yi ., yi″ + ... +, 2!, p!, , (4.20), , Note that Taylor series method is an explicit single step method., Using the definition given in (4.17), the truncation error of the method is given by, Ti+1 =, , h p+ 1, y( p + 1) ( xi + θh) ., ( p + 1) !, , (4.21), , Using the definition of the order given in (4.18), we say that the Taylor series method, (4.20) is of order p., For p = 1, we obtain the first order Taylor series method as, yi+1 = yi + hyi′ = yi + hf(xi, yi)., , (4.22), , This method is also called the Euler method. The truncation error of the Euler’s method is, T.E. =, , h2, yi′′ ( xi + θh) ., 2!, , (4.23), , Sometimes, we write this truncation error as, T.E. =, , h2, h3, y ′′ ( xi ) +, y ′′′( xi ) + ..., 2!, 3!, , (4.24), , 1, (T.E.) = O(h),, h, Euler method is a first order method. If the higher order derivatives can be computed, then, (4.24) can be used to predict the error in the method at any point., Since,, , Remark 1 Taylor series method cannot be applied to all problems as we need the higher order, derivatives. The higher order derivatives are obtained as, y′ = f(x, y), y″ =, y″′ =, , ∂, ∂x, , ∂f ∂f dy, +, = fx + f f y ,, ∂x ∂y dx, , FG ∂f + ∂f dy IJ + ∂ FG ∂f + ∂f dy IJ dy, H ∂x ∂y dx K ∂y H ∂x ∂y dx K dx, , = fxx + 2f fxy + f 2 fyy + fy(fx + f fy), etc., The number of partial derivatives required, increases as the order of the derivative of y, increases. Therefore, we find that computation of higher order derivatives is very difficult., Hence, we need suitable methods which do not require the computation of higher order, derivatives.
Page 197 :
186, , NUMERICAL METHODS, , Remark 2 The bound on the truncation error of the Taylor series method of order p is given, by, , |Ti + 1 |=, , h p+ 1, h p+ 1, y ( p+ 1) ( xi + θh) ≤, M p +1, ( p + 1) !, ( p + 1) !, , (4.25), , ( p+ 1), ( x)|., Mp+1 = max | y, , where, , x0 ≤ x ≤ b, , The bound on the truncation error of the Euler method (p = 1) is given by, | T.E. | ≤, , h2, max | y ′′( x)|., 2 x0 ≤ x ≤ b, , (4.26), , Remark 3 For performing the error analysis of the numerical methods, we need the Taylor, series expansion of function of two variables. The Taylor expansion is given by, , F ∂ + k ∂ IJ f (x, y) + 1 FG h ∂ + k ∂ IJ, f(x + h, y + k) = f(x, y) + G h, 2 ! H ∂x, ∂y K, H ∂x ∂y K, = f(x, y) + (h fx + k fy) +, , 2, , f ( x, y) + ..., , 1 2, (h fxx + 2hk f xy + k2 f yy ) + ..., 2!, , (4.27), , Remark 4 Extrapolation procedure (as described in numerical integration for Romberg integration) can also be used for the solution of the ordinary differential equations. We illustrate, this procedure for Euler’s method. Denote the numerical values obtained with step length h, by yE(h). Euler’s method is of first order, that is, the error expression is given by, y(x) – yE(h) = c1h + c2h2 + c3h3 + ..., , (4.28), , Repeating the computations with step length qh, 0 < q < 1, we get the error of approximation as, y(x) – yE(qh) = c1(qh) + c2(qh)2 + c3(qh)3 + ..., , (4.29), , Eliminating c1, we obtain, q[y(x) – yE(h)] – [y(x) – yE(qh)] = c2(q – q2)h2 + ..., or, , (q – 1)y(x) – [q yE(x) – yE(qh)] = c2(q – q2)h2 + ..., , Neglecting the O(h2) term, we get the new approximation to y(x) as, y(x) ≈, , [q yE (h) − yE (qh)], ., q−1, , y(x) ≈, , [(1/2) yE (h) − yE (h/2)], (1/2) − 1, , (4.30), , For q = 1/2, we get, , =, , [2 yE (h/2) − yE (h)], = [2yE(h/2) – yE(h)]., 2−1, , (4.31)
Page 198 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 187, , We can derive general formula for extrapolation. Let the step lengths be successively, reduced by the factor 2. That is, we use the step lengths, h, h/2, (h/22), ... . The formula is given, by, y(x) ≈ yE( m) (h) =, , 2 m yE( m− 1) (h/2) − yE(m −1) (h), ., 2m − 1, , (4.32), , For m = 1, we get the first column of approximations as, y(x) ≈, , 2 yE(0) (h/2) − yE(0) (h), ( 0), ( 0), = 2 y E ( h/2) − y E ( h ) ., 2−1, , (4.33), , For m = 2, we get the second column of approximations as, y(x) ≈, , 2 2 yE(1) (h/2) − yE(1) (h), ., 22 − 1, , (4.34), , Example 4.2 Solve the initial value problem yy′ = x, y(0) = 1, using the Euler method in 0 ≤ x, ≤ 0.8, with h = 0.2 and h = 0.1. Compare the results with the exact solution at x = 0.8. Extrapolate the result., Solution We have, Euler method gives, Initial condition gives, When h = 0.2, we get, , y′ = f(x, y) = (x/y)., yi+1 = yi + h f (xi, yi) = yi +, , hxi, ., yi, , x0 = 0, y0 = 1., yi+1 = yi +, , 0.2 xi, ., yi, , We have the following results., y(x1) = y(0.2) ≈ y1 = y0 +, , 0.2 x0, = 1.0., y0, , y(x2) = y(0.4) ≈ y2 = y1 +, , 0.2 x1, 0.2(0.2), = 1.0 +, = 1.04., 1.0, y1, , y(x3) = y(0.6) ≈ y3 = y2 +, , 0.2 x2, 0.2(0.4), = 1.11692, = 1.04 +, y2, 1.04, , y(x4) = y(0.8) ≈ y4 = y3 +, , 0.2 x3, 0.2(0.6), = 1.11692 +, = 1.22436., y3, 1.11692, , When h = 0.1, we get yi+1 = yi +, We have the following results., , 0.1 xi, ., yi
Page 199 :
188, , NUMERICAL METHODS, , y(x1) = y(0.1) ≈ y1 = y0 +, , 0.1x0, = 1.0., y0, , y(x2) = y(0.2) ≈ y2 = y1 +, , 0.1x1, 0.1(0.1), = 1.01., = 1.0 +, 1.0, y1, , y(x3) = y(0.3) ≈ y3 = y2 +, , 0.1x2, 0.1(0.2), = 1.01 +, = 1.02980., y2, 1.01, , y(x4) = y(0.4) ≈ y4 = y3 +, , 0.1x3, 0.1(0.3), = 1.0298 +, = 1.05893., y3, 1.0298, , y(x5) = y(0.5) ≈ y5 = y4 +, , 0.1x4, 0.1(0.4), = 1.05893 +, = 1.09670., 1.05893, y4, , y(x6) = y(0.6) ≈ y6 = y5 +, , 0.1x5, 0.1(0.5), = 1.0967 +, = 1.14229., y5, 1.0967, , y(x7) = y(0.7) ≈ y7 = y6 +, , 0.1x6, 0.1(0.6), = 1.14229 +, = 1.19482., y6, 1.14229, , y(x8) = y(0.8) ≈ y8 = y7 +, , 0.1x7, 0.1(0.7), = 1.19482 +, = 1.25341., y7, 1.19482, , The exact solution is y =, , x2 +1 ., , At x = 0.8, the exact value is y(0.8) = 1.64 = 1.28062., The magnitudes of the errors in the solutions are the following:, h = 0.2: | 1.28062 – 1.22436 | = 0.05626., h = 0.1: | 1.28062 – 1.25341 | = 0.02721., Using (4.31), we get the extrapolated result as, y(0.8) = [2yE(h/2) – yE(h)] = 2(1.25341) – 1.22436 = 1.28246., The magnitude of the error in the extrapolated result is given by, | 1.28062 – 1.28246 | = 0.00184., Example 4.3 Consider the initial value problem y′ = x(y + 1), y(0) = 1. Compute y(0.2) with h, = 0.1 using (i) Euler method (ii) Taylor series method of order two, and (iii) fourth order Taylor, 2, , x /2, series method. If the exact solution is y = –1 + 2 e, , find the magnitudes of the actual errors, for y(0.2). In the solutions obtained by the Euler method, find the estimate of the errors., , Solution We have, (i) Euler’s method:, , f(x, y) = x(y + 1), x0 = 0, y0 = 1., yi+1 = yi + h f(xi, yi) = yi + 0.1[xi (yi + 1)]., , With x0 = 0, y0 = 1, we get
Page 201 :
190, , NUMERICAL METHODS, , y(0.2) ≈ y2 = 1.010025 + 0.1(0.201003) + 0.005(2.030125) +, , 0.001, (0.605019), 6, , 0.0001, (6.150877) = 1.040402., 24, The exact value is y(0.1) = 1.010025, y(0.2) = 1.040403., +, , The magnitudes of the actual errors at x = 0.2 are, Euler method: | 1.02 – 1.040403 | = 0.020403., Taylor series method of second order:, , | 1.04025 – 1.040403 | = 0.000152., , Taylor series method of fourth order:, , | 1.040402 – 1.040403 | = 0.000001., , To estimate the errors in the Euler method, we use the approximation, T.E. ≈, We have, , h2, y ′′( xi ) ., 2!, , y0′ = 0, y0″ = 2., , [Estimate of error in y(0.1) at x = 0.1] ≈, , 0.01, (2) = 0.01., 2, , y1′ = x1 (y1 + 1) = 0.2,, y1″ = 1 + y1 + x1y1′ = 1 + 1 + 0.1(0.2) = 2.02., , 0.01, (2.02) = 0.0101., 2, Remark 4 In Example 4.3 (iii), notice that the contributions of the fourth and fifth terms on, the right hand side are 0.000101 and 0.000026 respectively. This implies that if the result is, required to be accurate for three decimal places only (the error is ≤ 0.0005), then we may, include the fourth term and the fifth term can be neglected., [Estimate of error in y(0.2) at x = 0.2] ≈, , Example 4.4 Find y at x = 0.1 and x = 0.2 correct to three decimal places, given, y′ – 2y = 3ex, y(0) = 0., , (A.U. Nov./Dec. 2006), , Solution The Taylor series method is given by, , y i +1 = yi + hyi′ +, We have, , h2, h3, h4 (4), y i′′+, yi′′′+, y + ..., 2!, 3!, 4! i, , y′ = 2y + 3ex, y″ = 2y′ + 3ex, y′″ = 2y″ + 3ex, y(4) = 2y″′ + 3ex., , With x0 = 0, y0 = 0, we get, y0′ = 2y0 + 3e0 = 3, y0″ = 2y0′ + 3 = 2(3) + 3 = 9,, y0″′ = 2y0″ + 3 = 2(9) + 3 = 21, y(4), 0 = 2y0″′ + 3 = 2(21) + 3 = 45.
Page 202 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 191, , The contribution of the fifth term on the right hand side of the Taylor series is, , h 4 (4) 0.0001, y0 =, (45) = 0.000187 < 0.0005., 4!, 24, Therefore, it is sufficient to consider the five terms on the right hand side of the Taylor, series. We obtain, y(0.1) ≈ y1 = y0 + 0.1 y0′ + 0.005y0″ +, = 0 + 0.1(3) + 0.005(9) +, , 0.001, 0.0001 ( 4 ), y 0 ′″ +, y0, 6, 24, , 0.001, 0.0001, (21) +, (45), 6, 24, , = 0.3 + 0.045 + 0.0035 + 0.000187 = 0.348687., With x1 = 0.1, y1 = 0.348687, we get, y1′ = 2y1 + 3e0.1 = 2(0.348687) + 3(1.105171) = 4.012887,, y1″ = 2y1′ + 3e0.1 = 2(4.012887) + 3(1.105171) = 11.341287,, y1″′ = 2y1″ + 3e0.1 = 2(11.341287) + 3(1.105171) = 25.998087,, , y1( 4 ) = 2 y1 ′″ + 3e 0.1 = 2(25.998087) + 3(1.105171) = 55.311687., The contribution of the fifth term on the right hand side of the Taylor series is, , h 4 (4) 0.0001, y0 =, (55.311687) = 0.00023 < 0.0005., 4!, 24, Therefore, it is sufficient to consider the five terms on the right hand side of the Taylor, series. We obtain, y(0.2) ≈ y2 = y1 + 0.1 y1′ + 0.005 y1″ +, , 0.001, 0.0001 ( 4 ), y1 ′″ +, y1, 6, 24, , = 0.348687 + 0.1(4.012887) + 0.005 (11.341287), +, , 0.001, 0.0001, (25.998087) +, (55.311687), 6, 24, , = 0.348687 + 0.401289 + 0.056706 + 0.004333 + 0.00023, = 0.811245., It is interesting to check whether we have obtained the three decimal place accuracy in, the solutions., The exact solution is y(x) = 3(e2x – ex), and y(0.1) = 0.348695, y(0.2) = 0.811266., The magnitudes of the errors are given by, | y(0.1) – y1 | = | 0.348695 – 0.348687 | = 0.000008., | y(0.2) – y2 | = | 0.811266 – 0.811245 | = 0.000021.
Page 203 :
192, , NUMERICAL METHODS, , Example 4.5 Find the first two non-zero terms in the Taylor series method for the solution of, the initial value problem, y′ = x2 + y2, y(0) = 0., Solution We have f(x, y) = x2 + y2. We have, y(0) = 0, y′(0) = 0 + [y(0)]2 = 0,, y″ = 2x + 2yy′, y″(0) = 0 + 2y(0)y′(0) = 0,, y″′ = 2 + 2[yy″ + (y′)2], y″′(0) = 2 + 2 [y(0) y″(0) + {y′(0)}2] = 2,, y(4) = 2[yy″′ + 3y′y″], y(4)(0) = 2[y(0)y″′(0) + 3y′(0)y″(0)] = 0,, y(5) = 2[yy(4) + 4y′y″′ + 3(y″)2],, y(5)(0) = 2[y(0)y(4)(0) + 4y′(0)y″′(0) + 3{y″(0)}2] = 0,, y(6) = 2[yy(5) + 5y′y(4) + 10y″y″′],, y(6)(0) = 2[y(0)y(5)(0) + 5y′(0)y(4)(0) + 10y″(0)y″′(0)] = 0,, y(7) = 2[yy(6) + 6y′y(5) + 15y″y(4) + 10(y″′)2],, y(7)(0) = 2[y(0) y(6)(0) + 6y′(0)y(5)(0) + 15y″(0)y(4)(0) + 10{y″′(0)}2] = 80., The Taylor series with first two non-zero terms is given by, y(x) =, , x3 x7, ., +, 3, 63, , We have noted earlier that from application point of view, the Taylor series method has, the disadvantage that it requires expressions and evaluation of partial derivatives of higher, orders. Since the derivation of higher order derivatives is difficult, we require methods which, do not require the derivation of higher order derivatives. Euler method, which is an explicit, method, can always be used. However, it is a first order method and the step length h has to be, chosen small in order that the method gives accurate results and is numerically stable (we, shall discuss this concept in a later section)., We now derive methods which are of order higher than the Euler method., 4.3.1 Modified Euler and Heun’s Methods, First, we discuss an approach which can be used to derive many methods and is the basis for, Runge-Kutta methods, which we shall derive in the next section. However, all these methods, must compare with the Taylor series method when they are expanded about the point x = xi., Integrating the differential equation y′ = f(x, y) in the interval [xi, xi+1], we get, , z, , x i +1, , xi, , or, , dy, dx =, dx, , z, , x i +1, , xi, , f ( x , y ) dx, , y(xi+1) = y(xi) +, , z, , x i +1, , xi, , f ( x , y ) dx ., , (4.35)
Page 204 :
193, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , Applying the mean value theorem of integral calculus to the right hand side, we obtain, y(xi+1) – y(xi) = (xi+1 – xi) f (xi + θ h, y(xi + θh)),, or, , y(xi+1) = y(xi) + h f (xi + θ h, y(xi + θh)), 0 < θ < 1., , (4.36), , Since xi+1 – xi = h. Any value of θ ∈ [0, 1] produces a numerical method., We note that y′ and hence f(x, y) is the slope of the solution curve. In (4.35), the integrand, on the right hand side is the slope of the solution curve which changes continuously in [xi, xi+1]., If we approximate the continuously varying slope in [xi, xi+1] by a fixed slope or by a linear, combination of slopes at several points in [xi, xi+1], we obtain different methods., Case 1 Let θ = 0. In this case, we are approximating the continuously varying slope in [xi, xi+1], by the fixed slope at xi . We obtain the method, yi+1 = yi + hf(xi, yi),, which is the Euler method. The method is of first order., Case 2 Let θ = 1. In this case, we are approximating the continuously varying slope in [xi, xi+1], by the fixed slope at xi+1. We obtain the method, yi+1 = yi + hf(xi+1, yi+1),, , (4.37), , which is an implicit method as the nonlinear term f(xi+1, yi+1) occurs on the right hand side., This method is called backward Euler method. The method is of first order., The method can be made explicit by writing the approximation yi+1 = yi + hf (xi , yi ) on, the right hand side of (4.37). Then, we have the explicit method, yi+1 = yi + hf(xi+1, yi + hf(xi))., , (4.38), , Case 3 Let θ = 1/2. In this case, we are approximating the continuously varying slope in, [xi, xi+1] by the fixed slope at xi+1/2. We obtain the method, , FG, H, , yi+1 = yi + hf xi +, , FG, H, , h, h, , y xi +, 2, 2, , IJ IJ ., KK, , However, xi + (h/2) is not a nodal point. If we approximate y(xi + (h/2)) on the right hand, side by Euler method with spacing h/2, that is,, , FG, H, , y xi +, we get the method, , IJ, K, , h, h, = yi +, f(xi, yi),, 2, 2, , FG, H, , yi+1 = yi + hf xi +, , IJ, K, , h, h, , yi + f ( xi , yi ) ., 2, 2, , (4.39), , The method is called a modified Euler method or mid-point method. The slope at the, mid-point is replaced by an approximation to this slope.
Page 205 :
194, , NUMERICAL METHODS, , Error of approximation, The truncation error in the method is given by, , FG, H, , T.E. = y(xi+1) – y(xi) – hf x i +, , LM y + hy′ + h, 2, N, , 2, , =, , IJ, K, , h, h, , y( x i ) + f ( x i , y i ), 2, 2, , OP, Q, , LM, N, , y′′ + ... − y − h f +, , OP, Q, , h, h, fx + f f y + (three terms of h 2 ) + ..., 2, 2, , where all the terms are evaluated at (xi , yi ). Using the expressions for y′ and y″, we obtain, , LM, N, , T.E. = y + hf +, , LM, N, , –h f +, , OP, Q, O, + (three terms of h ) + ...P, Q, , h2, ( fx + f f y ) + (five terms of h 3 ) + ... – y, 2, , h, h, fx + f f y, 2, 2, , = (terms of h3) + ..., , 2, , The truncation error is of order O(h3). Therefore, the method is of second order., Case 4 Let the continuously varying slope in [xi, xi+1] be approximated by the mean of slopes, at the points xi and xi+1. Then, we obtain the method, , h, [f(xi, yi) + f(xi+1, yi+1)], 2, , yi+1 = yi +, , h, [f + fi+1], 2 i, , = yi +, , (4.40), , where f(xi, yi) = fi and f(xi+1, yi+1) = fi + 1. The method is an implicit method. It is also called the, trapezium method. The method can be made explicit by writing the approximation, yi+1 = yi + hf(xi, yi) = yi + h fi, on the right hand side of (4.32). Then, we have the explicit method, yi+1 = yi +, , h, [f(xi, yi) + f(xi+1, yi + h fi)]., 2, , (4.41), , The slope at the point xi+1 is replaced by an approximation to this slope. The method is, called Heun’s method or Euler-Cauchy method., Error of approximation, The truncation error in the method is given by, T.E. = y(xi+1) – y(xi) –, , LM, N, , = y + hy ′ +, , h, [f(xi) + f(xi + h, yi + h f(xi))], 2, , OP, Q, , h2, h, 2 f + h f x + hf f y + (three terms of h 2 ) + ..., y ′′ + ... − y −, 2, 2, , where all the terms are evaluated at (xi, yi). Using the expressions for y′ and y″, we obtain
Page 206 :
195, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , LM y + hf + h, 2, N, , 2, , T.E. =, , –, , OP, Q, , ( fx + f f y ) + (five terms of h 3 ) + ... – y, , h, [2f + h fx + h f fy + (three terms of h2) + ...], 2, , = (terms of h3) + ..., The truncation error is of order O(h3). Therefore, the method is of second order., Example 4.6 Solve the following initial value problem using the modified Euler method and, Heun’s method with h = 0.1 for x ∈ [0, 0.3]., y′ = y + x, y(0) = 1., Compare with the exact solution y(x) = 2ex – x – 1., Solution, (i) Modified Euler method is given by, , FG, H, , yi+1 = yi + h f xi +, , IJ, K, , h, h, , yi + f ( xi , yi ), 2, 2, , = yi + 0.1 f(xi + 0.05, yi + 0.05 f(xi, yi))., We have, , x0 = 0, y0 = 1.0, y0′ = f0 = y0 + x0 = 1.0, y(0.1) ≈ y1 = y0 + 0.1 f(x0 + 0.05, y0 + 0.05 f0), = 1.0 + 0.1 f(0.05, 1.05) = 1.0 + 0.1 (1.1) = 1.11., x1 = 0.1, y1 = 1.11, y1′ = f1 = y1 + x1 = 1.11 + 0.1 = 1.21., y(0.2) ≈ y2 = y1 + 0.1 f(x1 + 0.05, y1 + 0.05 f1), = 1.11 + 0.1 f(0.15, 1.11 + 0.05(1.21)), = 1.11 + 0.1 f(0.15, 1.1705) = 1.24205., x2 = 0.2, y2 = 1.24205, y2′ = f2 = y2 + x2 = 1.24205 + 0.2 = 1.44205., y(0.3) ≈ y3 = y2 + 0.1 f(x2 + 0.05, y2 + 0.05 f2), = 1.24205 + 0.1 f(0.25, 1.24205 + 0.05(1.44205)), = 1.24205 + 0.1 f(0.25, 1.31415) = 1.39846., , The errors in the solution are given in Table 4.1., Table 4.1. Errors in the modified Euler method. Example 4.6., Point, , Numerical solution, , Exact solution, , Magnitude of error, , 0.1, , 1.11, , 1.11034, , 0.00034, , 0.2, , 1.24205, , 1.24281, , 0.00076, , 0.3, , 1.39846, , 1.39972, , 0.00126
Page 207 :
196, , NUMERICAL METHODS, , (ii) The Heun’s method is given by, yi+1 = yi +, , h, [f(xi, yi) + f(xi+1, yi + h fi)], 2, , = yi + 0.05 [f(xi, yi) + f(xi+1, yi + 0.1 fi)], Denote yi* = yi + 0.1 fi. Then, we write the method as, yi+1 = yi + 0.05 [f(xi, yi) + f(xi+1, yi*)], We have, , x0 = 0, y0 = 1.0, y0′ = f0 = y0 + x0 = 1.0, y0* = y0 + 0.1 f0 = 1 + 0.1 (1) = 1.1., y(0.1) ≈ y1 = y0 + 0.05[f0 + f(x1, y0*)], = 1.0 + 0.05[1.0 + 1.2] = 1.11., x1 = 0.1, y1 = 1.11, y1′ = f1 = y1 + x1 = 1.11 + 0.1 = 1.21., y1* = y1 + 0.1 f1 = 1.11 + 0.1 (1.21) = 1.231., y(0.2) ≈ y2 = y1 + 0.05[f1 + f(x2, y1*)], = 1.11 + 0.05[1.21 + f(0.2, 1.231)], = 1.11 + 0.05 [1.21 + 1.431] = 1.24205., x2 = 0.2, y2 = 1.24205, y2′ = f2 = f(0.2, 1.24205) = 1.44205., y2* = y2 + 0.1 f2 = 1.24205 + 0.1 (1.44205) = 1.38626., y(0.3) ≈ y3 = y2 + 0.05 [f2 + f(x3, y2*)], = 1.24205 + 0.05[f2 + f(0.3, 1.38626)], = 1.24205 + 0.05[1.44205 + 1.68626] = 1.39847., , The errors in the solution are given in Table 4.2. Note that the modified Euler method, and the Heun’s method have produced the same results in this problem., Table 4.2. Errors in modified Euler method. Example 4.6., Point, , Numerical solution, , Exact solution, , Magnitude of error, , 0.1, , 1.11, , 1.11034, , 0.00034, , 0.2, , 1.24205, , 1.24281, , 0.00076, , 0.3, , 1.39847, , 1.39972, , 0.00125, , Example 4.7 For the following initial value problem, obtain approximations to y(0.2) and, y(0.4), using the modified Euler method and the Heun’s method with h = 0.2., y′ = – 2xy2, y(0) = 1., Compare the numerical solutions with the exact solution y(x) = 1/(1 + x2)., Solution, (i) Modified Euler method is given by
Page 209 :
198, , NUMERICAL METHODS, , REVIEW QUESTIONS, 1. Define truncation error of a single step method for the solution of the initial value problem, y′ = f (x, y), y(x0) = y0., Solution A single step method for the solution of the given initial value problem is, given by, yi+1 = yi + hφ(xi+1, xi, yi+1, yi, h)., The exact solution y(xi) satisfies the equation, y(xi+1) = y(xi) + hφ(xi+1, xi, y(xi+1), y(xi), h) + Ti+1, where Ti+1 is called the local truncation error or discretization error. Therefore, the, Truncation error (T.E.) is defined by, Ti+1 = y(xi+1) – y(xi) – hφ(xi+1, xi, y(xi+1), y(xi), h)., , 2. Define the order of a numerical method for the solution of the initial value problem y′ = f(x, y),, y(x0) = y0., Solution Let Ti+1 define the truncation error of the numerical method. The order of a, method is the largest integer p for which, 1, Ti + 1 = O(h p ) ., h, , 3. Write the truncation error of the Euler’s method., Solution The truncation error of the Euler’s method is, T.E. =, , h2, y″(xi + θh),, 2!, , 0 < θ < 1., , 4. Write the bound on the truncation error of the Euler’s method., Solution The bound on the truncation error of the Euler method (p = 1) is given by, | T.E. | ≤, , h2, max | y ′′( x)|., 2 x0 ≤ x ≤ b, , 5. What is the disadvantage of the Taylor series method ?, Solution Taylor series method requires the computation of higher order derivatives., The higher order derivatives are given by, y′ = f(x, y),, , y″′ =, , FG, H, , y″ =, , ∂f ∂f dy, = fx + f fy,, +, ∂x ∂y dx, , IJ, K, , FG, H, , IJ, K, , ∂ ∂f ∂f dy, ∂ ∂f ∂f dy dy, +, +, +, ∂x ∂x ∂y dx, ∂y ∂x ∂y dx dx, , = fxx + 2 f fxy + f2 fyy + fy(fx + f fy), etc.
Page 210 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 199, , The number of partial derivatives to be computed increases as the order of the derivative, of y increases. Therefore, we find that computation of higher order derivatives is very, difficult., 6. Write the bound on the truncation error of the Taylor series method., Solution The bound on the truncation error of the Taylor series method of order p is, given by, | Tp+1 | =, where, , h p +1, h p +1, y ( p +1) ( x i + θh ) ≤, M p +1, ( p + 1) !, ( p + 1) !, , Mp+1 =, , max | y ( p+ 1) ( x)|., , x0 ≤ x ≤ b, , 7. What are the orders of (i) modified Euler method, (ii) Heun’s method ?, Solution Modified Euler method and Heun’s method are both second order methods., , EXERCISE 4.1, Solve the following initial value problems using (i) Euler method, (ii) modified Euler method,, and (iii) Heun’s method with h = 0.1, x ∈ [1, 1.2]. Compare with the exact solution., 1. y′ = x + y, y(1) = 0., 2. y′ = –y2, y(1) = 1., 3. Find an approximation to y(0.4), for the initial value problem, y′ = x2 + y2, y(0) = 1, using the Euler method with h = 0.1 and h = 0.2. Extrapolate the results to get a better, approximation to y(0.4)., 4. Find an approximation to y(1.6), for the initial value problem, y′ = x + y2, y(1) = 1, using the Euler method with h = 0.1 and h = 0.2. Extrapolate the results to get a better, approximation to y(1.6)., 5. Given the initial value problem,, y′ = 2x + cos y, y(0) = 1, show that it is sufficient to use Euler method with step length h = 0.2 to compute y(0.2), with an error less than 0.05., 6. Use Taylor series method of order four to solve, y′ = x2 + y2, y(0) = 1, for x ∈ [0, 0.4] with h = 0.2, 7. Apply Taylor series method of second order and Heun’s method to integrate, y′ = 2x + 3y, y(0) = 1, x ∈ [0, 0.4], with h = 0.1.
Page 211 :
200, , NUMERICAL METHODS, , 8. Obtain numerical solution correct to two decimals for the initial value problem, y′ = 3x + 4y, y(0) = 1, x ∈ [0, 0.2], using the Taylor series method with h = 0.1., 9. Obtain numerical solution correct to two decimals for the initial value problem, y′ = 3x + y2, y(1) = 1, x ∈ [1, 1.2], using the Taylor series method with h = 0.1., In the following problems, obtain the solution by Taylor series method., 10. Find y at x = 0.1 if y′ = x2y – 1, y(0) = 1., , (A.U. Nov./Dec. 2004), , 11. Find y(1.1) given that y′ = x + y, y(1) = 0., , (A.U. Nov./Dec. 2006), , 12. Find the values y at x = 0.1 and x = 0.2, given, y′ = x + y, y(0) = 1., , (A.U. April/May 2005), , 13. Get the value of y at x = h, given, y′ = x + y + xy, y(0) = 1., , (A.U. Nov./Dec. 2006), , Using the modified Euler method, solve the following initial value problems., 14. Find y(0.1) if y′ = x2 + y2, y(0) = 1., , (A.U. Nov./Dec. 2004), , 15. Find y(0.2), given the initial value problem y′ = y –, , x2, , + 1, y(0) = 0.5., , (A.U. April/May 2003 ; Nov./Dec. 2006), , 4.4, , RUNGE-KUTTA METHODS, , Integrating the differential equation y′ = f (x, y) in the interval [xi, xi+1], we get, , z, , x i +1, , xi, , dy, dx =, dx, , z, , x i +1, , xi, , f ( x , y ) dx ., , (4.42), , We have noted in the previous section, that y′ and hence f (x, y) is the slope of the, solution curve. Further, the integrand on the right hand side is the slope of the solution curve, which changes continuously in [xi, xi+1]. By approximating the continuously varying slope in, [xi, xi+1] by a fixed slope, we have obtained the Euler, Heun’s and modified Euler methods. The, basic idea of Runge-Kutta methods is to approximate the integral by a weighted average of, slopes and approximate slopes at a number of points in [xi, xi+1]. If we also include the slope at, xi+1, we obtain implicit Runge-Kutta methods. If we do not include the slope at xi+1, we obtain, explicit Runge-Kutta methods. For our discussion, we shall consider explicit Runge-Kutta methods only. However, Runge-Kutta methods must compare with the Taylor series method when, they are expanded about the point x = xi. In all the Runge-Kutta methods, we include the slope, at the initial point x = xi, that is, the slope f(xi, yi)., Runge-Kutta method of second order, Consider a Runge-Kutta method with two slopes. Define, k1 = h f(xi , yi ),, k2 = h f(xi + c2h, yi + a21k1),
Page 213 :
202, , NUMERICAL METHODS, , k1 = hf(xi , yi ), k2 = h f(xi + h, yi + k1), which is the Heun’s method or Euler-Cauchy method. Therefore, Heun’s method derived in, the previous section can be written in the formulation of a Runge-Kutta method., If we choose c2 = 1/2, we get w1 = 0. The method is given by, yi+1 = yi + k2, , (4.48), , k1 = hf (xi , yi),, , FG, H, , h, 1, , yi + k1, 2, 2, , k2 = hf xi +, , IJ, K, , which is the modified Euler method. Therefore, modified Euler method can also be written in, the formulation of a Runge-Kutta method., Error of the Runge-Kutta method, Subtracting (4.45) from (4.44), we get the truncation error in the method as, T.E. = y(xi+1) – yi+1, = h3, , LMFG 1 − c IJ { f, NH 6 4 K, 2, , xx, , + 2ffxy + f 2 f yy } +, , OP, Q, , 1, f y ( f x + ff y ) + ..., 6, , (4.49), xi, , Since the truncation error is of order O(h3), the method is of second order for all values, of c2. Therefore, (4.46) gives an infinite family of second order methods. We may note that for, c2 = 2/3, the first term inside the bracket in (4.49) vanishes and we get a method of minimum, truncation error. The method is given by, yi+1 = yi +, where, , 1, (k + 3k2), 4 1, , (4.50), , k1 = hf(xi, yi),, , FG, H, , k2 = hf xi +, , IJ, K, , 2, 2, h, yi + k1 ., 3, 3, , Therefore, the method (4.50) is a second order method with minimum truncation error., Runge-Kutta method of fourth order The most commonly used Runge-Kutta method is a, method which uses four slopes. The method is given by, yi+1 = yi +, , 1, (k + 2k2 + 2k3 + k4), 6 1, , k1 = hf (xi , yi ), , FG, H, F, = hf G x, H, , k2 = hf xi +, k3, , i, , +, , IJ, K, 1 I, + k J ,, 2 K, , h, 1, , yi + k1 ,, 2, 2, , h, , yi, 2, , k4 = hf (xi + h, yi + k3)., , 2, , (4.51)
Page 214 :
203, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , Remark 5 We would like to know as to why the Runge-Kutta method (4.51) is the most, commonly used method. Using two slopes in the method, we have obtained methods of second, order, which we have called as second order Runge-Kutta methods. The method has one, arbitrary parameter, whose value is suitably chosen. The methods using four evaluations of, slopes have two arbitrary parameters. The values of these parameters are chosen such that, the method becomes simple for computations. One such choice gives the method (4.51). All, these methods are of fourth order, that is, the truncation error is of order O(h5). The method, (4.51) is called the classical Runge-Kutta method of fourth order. If we use five slopes, we do, not get a fifth order method, but only a fourth order method. It is due to this reason the, classical fourth order Runge-Kutta method is preferred for computations., Remark 6 All the single step methods (Taylor series, Runge-Kutta methods etc.) are self, starting. They do not require values of y and/or the values of the derivatives of y beyond the, previous point., Example 4.8 Solve the initial value problem, y′ = – 2xy2, y(0) = 1, with h = 0.2 on the interval [0, 0.4]. Use (i) the Heun’s method (second order Runge-Kutta, method); (ii) the fourth order classical Runge-Kutta method. Compare with the exact solution, y(x) = 1/(1 + x2)., Solution, (i) The solution using Heun’s method is given in Example 4.7. The solutions are, y(0.2) ≈ 0.96, y(0.4) ≈ 0.86030., (ii) For i = 0, we have x0 = 0, y0 = 1., k1 = hf (x0, y0) = –2(0.2)(0)(1)2 = 0,, , FG, H, F, = hf G x, H, , k2 = hf x0 +, k3, , 0, , IJ, K, 1 I, + k J = –2 (0.2)(0.1)(0.98), 2 K, , 1, h, , y0 + k1 = –2(0.2)(0.1)(1)2 = –0.04,, 2, 2, , +, , h, , y0, 2, , 2, , 2, , = –0.038416,, , k4 = hf (x0 + h, y0 + k3) = –2(0.2)(0.2)(0.961584)2 = –0.0739715,, y(0.2) ≈ y1 = y0 +, , 1, (k + 2k2 + 2k3 + k4), 6 1, , = 1.0 +, For i = 1, we have, , 1, [0.0 – 0.08 – 0.076832 – 0.0739715] = 0.9615328., 6, , x1 = 0, y1 = 0.9615328., k1 = h f (x1, y1) = –2(0.2)(0.2)(0.9615328)2 = – 0.0739636,
Page 215 :
204, , NUMERICAL METHODS, , FG, H, F, = hf G x, H, , k2 = hf x1 +, k3, , 1, , +, , IJ, K, 1 I, + k J = –2(0.2)(0.3)(0.9102451), 2 K, , h, 1, , y1 + k1 = –2(0.2)(0.3) (0.924551)2 = – 0.1025753,, 2, 2, h, , y1, 2, , 2, , 2, , = – 0.0994255,, , k4 = hf (x1 + h, y1 + k3) = –2(0.2)(0.4)(0.86210734)2 = – 0.1189166,, y(0.4) ≈ y2 = y1 +, , 1, (k + 2k2 + 2k3 + k4), 6 1, , = 0.9615328 +, , 1, [–0.0739636 –0.2051506 –0.1988510 –, 6, , 0.1189166], = 0.8620525, The absolute errors in the numerical solutions are given in Table 4.4., Table 4.4. Absolute errors in Heun’s method and fourth order Runge-Kutta method. Example 4.8., Heun’s method, , Runge-Kutta method, , x, , Exact solution, , Num. solution, , | Error |, , Num. solution, , | Error |, , 0.2, , 0.9615385, , 0.96, , 0.0015385, , 0.9615328, , 0.0000057, , 0.4, , 0.8620690, , 0.86030, , 0.0017690, , 0.8620525, , 0.0000165, , Example 4.9 Given y′ = x3 + y, y(0) = 2, compute y(0.2), y(0.4) and y(0.6) using the Runge-Kutta, method of fourth order., (A.U. April/May 2004), Solution We have, , x0 = 0, y0 = 2, f(x, y) = x3 + y, h = 0.2., , For i = 0, we have, , x0 = 0, y0 = 2., k1 = hf(x0, y0) = 0.2 f (0, 2) = (0.2)(2) = 0.4,, , FG, H, , k2 = hf x0 +, , IJ, K, , 1, h, , y0 + k1 = 0.2 f(0.1, 2.2), 2, 2, , = (0.2)(2.201) = 0.4402,, , FG, H, , k3 = hf x0 +, , h, 1, , y0 + k2, 2, 2, , IJ = 0.2 f(0.1, 2.2201), K, , = (0.2)(2.2211) = 0.44422,, k4 = hf (x0 + h, y0 + k3) = 0.2 f (0.2, 2.44422), = (0.2)(2.45222) = 0.490444,, y(0.2) ≈ y1 = y0 +, , 1, (k + 2k2 + 2k3 + k4), 6 1
Page 216 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , = 2.0 +, , 205, , 1, [0.4 + 2(0.4402) + 2(0.44422) + 0.490444], 6, , = 2.443214., For i = 1, we have, , x1 = 0.2, y1 = 2.443214., k1 = h f (x1, y1) = 0.2 f(0.2, 2.443214) = (0.2)(2.451214) = 0.490243,, , FG, H, , k2 = hf x1 +, , IJ, K, , 1, h, , y1 + k1 = 0.2 f(0.3, 2.443214 + 0.245122), 2, 2, , = (0.2)(2.715336) = 0.543067,, , FG, H, , k3 = hf x1 +, , h, 1, , y1 + k2, 2, 2, , IJ = 0.2 f(0.3, 2.443214 + 0.271534), K, , = (0.2)(2.741748) = 0.548350,, k4 = hf (x1 + h, y1 + k3) = 0.2 f(0.4, 2.443214 + 0.548350), = (0.2)(3.055564) = 0.611113,, y(0.4) ≈ y2 = y1 +, , 1, (k + 2k2 + 2k3 + k4), 6 1, , = 2.443214 +, , 1, [0.490243 + 2(0.543067) + 2(0.548350) + 0.611113], 6, , = 2.990579., For i = 2, we have, , x2 = 0.4, y2 = 2.990579., k1 = hf (x2, y2) = 0.2 f (0.4, 2.990579) = (0.2)(3.054579) = 0.610916,, , FG, H, , k2 = hf x2 +, , 1, h, , y2 + k1, 2, 2, , IJ, K, , = 0.2 f(0.5, 2.990579 + 0.305458), = (0.2)(3.421037) = 0.684207,, , FG, H, , k3 = hf x2 +, , 1, h, , y2 + k2, 2, 2, , IJ = 0.2f (0.5, 2.990579 + 0.342104), K, = (0.2)(3.457683) = 0.691537,, , k4 = hf (x2 + h, y2 + k3) = 0.2 f (0.6, 2.990579 + 0.691537), = (0.2) (3.898116) = 0.779623., y(0.6) ≈ y3 = y2 +, , 1, (k + 2k2 + 2k3 + k4), 6 1, , = 2.990579 +, = 3.680917., , 1, [0.610916 + 2(0.684207) + 2(0.691537) + 0.779623], 6
Page 217 :
206, , NUMERICAL METHODS, , REVIEW QUESTIONS, 1. Write the Heun’s method for solving the first order initial value problems in the RungeKutta formulation., Solution Heun’s method can be written as follows, yi+1 = yi +, , 1, (k + k2), 2 1, , k1 = hf (xi , yi),, k2 = hf (xi + h, yi + k1)., 2. Write the modified Euler method for solving the first order initial value problems in the, Runge-Kutta formulation., Solution Modified Euler method can be written as follows, yi+1 = yi + k2, k1 = hf (xi , yi), , FG, H, , k2 = hf xi +, , IJ, K, , 1, h, , yi + k1 ., 2, 2, , 3. Why is the classical Runge-Kutta method of fourth order, the most commonly used, method for solving the first order initial value problems ?, Solution Using two slopes in the method, we can obtain methods of second order, which, are called as the second order Runge-Kutta methods. The method has one arbitrary, parameter, whose value is suitably chosen. The methods using four evaluations of slopes, have two arbitrary parameters. All these methods are of fourth order, that is the truncation error is of order O(h5 ). The values of these parameters are chosen such that the, method becomes simple for computations. One such choice gives the classical RungeKutta method of fourth order. If we use five slopes, we do not get a fifth order method,, but only a fourth order method. It is due to this reason, the classical fourth order RungeKutta method is preferred for computations., , EXERCISE 4.2, In the following problems, obtain the solution by the fourth order Runge-Kutta method., 1. Find f(0.4), f(0.6), given the initial value problem y′ = y – x2 + 1, y(0) = 0.5., (A.U. April/May 2003), 2. Solve, , dy y 2 − x 2, with y(0) = 1 at x = 0.2., =, dx y 2 + x 2, , (A.U. April/May 2005, Nov./Dec. 2004), , 3. Find y(0.1) and y(0.2) for the initial value problem y′ = x + y2, y(0) = 1.
Page 218 :
207, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 4. Find y(0.4) given that y′ = x + y2, y(0) = 1.3456. Take h = 0.2., 5. Determine y(0.2) with h = 0.1, for the initial value problem y′ = x2 + y2, y(0) = 1., 6. Find an approximate value of y when x = 0.2 and x = 0.4 given that y′ = x + y, y(0) = 1,, with h = 0.2., (A.U. May/June 2006, Nov./Dec. 2006), 7. Determine y(0.2), y(0.4) with h = 0.2, for the initial value problem y′ = x3 + 3y, y(0) = 1., 8. Solve, , dy y − x 2, , y(0) = 1 at x = 0.2 with h = 0.1., =, dx y + x 2, , 4.5, , SYSTEM OF FIRST ORDER INITIAL VALUE PROBLEMS, , In section 4.1, we have discussed the reduction of a second order initial value problem to a, system of first order initial value problems. For the sake of completeness, let us repeat this, procedure., Let the second order initial value problem be given as, a0(x) y″(x) + a1(x)y′(x) + a2(x)y(x) = r(x), , (4.52), , y(x0) = b0, y′(x0) = b1., Define u1 = y. Then, we have the system, u1′ = y′ = u2, u1(x0) = b0,, u2′ = y″ =, =, , 1, [r(x) – a1(x) y′(x) – a2(x) y(x)], a0 ( x), 1, [r(x) – a1(x) u2 – a2(x) u1], u2(x0) = b1., a0 ( x), , The system is given by, , LMu OP′ = LMu, OP , LMu (x ) OP = LMb OP, (, ,, ,, ), u, f, x, u, u, N Q N, Q Nu (x )Q Nb Q, where, , 1, , 2, , 2, , 2, , f2 (x, u1, u2) =, , 1, , 2, , 1, , 0, , 0, , 2, , 0, , 1, , (4.53), , 1, [r(x) – a1(x) u2 – a2(x) u1]., a0 ( x), , In general, we may have a system as, , LM y OP′ = LM f (x, y , y )OP , LM y (x ) OP = LMb OP ., N y Q N f (x, y , y ) Q N y (x )Q Nb Q, 1, , 1, , 1, , 2, , 1, , 0, , 0, , 2, , 2, , 1, , 2, , 2, , 0, , 1, , In vector notation, denote, y = [y1, y2]T, f = [f1, f2]T, b = [b0, b1]T., , (4.54)
Page 222 :
211, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , FG, H, , k23 = hf2 x1 +, , h, 1, 1, , u1 + k12 , v1 + k22, 2, 2, 2, , IJ, K, , = 0.2 f2 (0.3, 0.1006, 0.2217), = 0.2 [3(0.1006) – 4(0.2217)] = – 0.1170., k14 = hf1(x1 + h, u1 + k13, v1 + k23), = 0.2 f1(0.4, 0.1284, 0.1423), = 0.2[– 3(0.1284) + 2(0.1423)] = – 0.0201., k24 = hf2 (x1 + h, u1 + k13, v1 + k23), = 0.2 f2(0.4, 0.1284, 0.1423), = 0.2[3(0.1284) – 4(0.1423)] = – 0.0368., , 1, (k + 2k12 + 2k13 + k14), 6 11, , u(0.4) ≈ u2 = u1 +, = 0.1001 +, v(0.4) ≈ v2 = v1 +, = 0.2593 +, , 1, (0.0437 + 0.0020 + 0.0566 – 0.0201) = 0.1138., 6, 1, (k + 2k22 + 2k23 + k24), 6 21, 1, (– 0.1474 – 0.1506 – 0.2340 – 0.0368) = 0.1645., 6, , Example 4.11 Compute approximations to y(0.4) and y′(0.4), for the initial value problem, y″ + 4y = cos t, y(0) = 1, y′(0) = 0, using (i) Taylor series method of fourth order, (ii) Runge-Kutta method of fourth order, with, step length h = 0.2. If exact solution is given by y(t) = (2 cos 2t + cos t)/3, find the magnitudes of, the errors., Solution Let y = u. Reducing the given second order equation to a system of first order, equations, we obtain, u′ = v, u(0) = 1,, v′ = cos t – 4y = cos t – 4u, v(0) = 0., (i) Taylor series method of fourth order gives, ui+1 = ui + hui′ +, , h2, h3, h 4 (4), ui′′ +, u i′′′+, u, 2, 6, 24 i, , = ui + 0.2 ui′ + 0.02 ui″ +, vi+1 = vi + hvi +, , 0.008, 0.0016 ( 4 ), u i′′′ +, ui, 6, 24, , h2, h3, h4 (4), vi″ +, vi′′′ +, v, 2, 6, 24 i
Page 224 :
213, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , = – 0.585333 + 0.2(– 2.782865) + 0.02(2.142663), +, , 0.008, 0.0016, (10.151393) +, (– 8.371983) = – 1.086076., 6, 24, , The exact solutions are, u(0.2) =, , 1, [2 cos (0.4) + cos (0.2)] = 0.940730., 3, , v(0.2) = –, u(0.4) =, , 1, [4 sin (0.4) + sin (0.2)] = – 0.585448., 3, , 1, [2 cos (0.8) + cos (0.4)] = 0.771491., 3, , v(0.4) = –, , 1, [4 sin (0.8) + sin (0.4)] = – 1.086281., 3, , The magnitudes of errors in the solutions are, | u(0.2) – u1 | = | 0.940730 – 0.940733 | = 0.000003,, | v(0.2) – v1 | = | – 0.585448 + 0.585333 | = 0.000115,, | u(0.4) – u2 | = | 0.771491 – 0.771543 | = 0.000052,, | v(0.4) – v2 | = | – 1.086281 + 1.086076 | = 0.000205., (ii) For i = 0, we have t0 = 0, u0 = 1, v0 = 0, f1(u, v) = v, f2(u, v) = cos t – 4u., k11 = hf1(t0, u0, v0) = hf1(0, 1, 0) = 0., k21 = hf2(t0, u0, v0) = hf2(0, 1, 0) = 0.2 (1 – 4) = – 0.6., , FG, H, , k12 = hf1 t0 +, , h, 1, 1, , u0 + k11, v0 + k21, 2, 2, 2, , IJ, K, , = 0.2 f1(0.1, 1 + 0.0, 0.0 – 0.3) = 0.2 f1(0.1, 1.0, – 0.3), = 0.2 (– 0.3) = – 0.06., , FG, H, , k22 = hf2 t0 +, , 1, 1, h, , u0 + k11, v0 + k21, 2, 2, 2, , IJ, K, , = 0.2 f2 (0.1, 1.0, – 0.3) = 0.2 [cos (0.1) – 4] = – 0.600999., , FG, H, , k13 = hf1 t0 +, , h, 1, 1, , u0 + k12 , v0 + k22, 2, 2, 2, , IJ, K, , = 0.2 f1(0.1, 1.0 – 0.03, 0.0 – 0.3004995), = 0.2 f1(0.1, 0.97, – 0.3004995), = 0.2 (– 0.3004995) = – 0.060100.
Page 227 :
216, , NUMERICAL METHODS, , 2. y″ – 6y′ + 5y = sin 2t, with y(0) = 0 and y′(0) = 1., 3. y″ – 2y′ + y = tet, with y(0) = 0.5 and y′(0) = 0.8., Solve the following second order initial value problems by Taylor series method., 4. y″ – 2y′ + 2y = e2t sin t, with y(0) = – 0.4 and y′(0) = – 0.6. Find y(0.1)., (A.U.April/May 2003), 5. y″ + 3y′ + 2y =, , et,, , with y(0) = 1 and y′(0) = 1. Find y(0.2) with h = 0.2., , 6. y″ – 4y′ + 4y = e2t, with y(0) = 0.5 and y′(0) = 1. Find y(0.2) with h = 0.1., 7. y″ – 6y′ + 5y = et, with y(0) = 0 and y′(0) = – 1. Find y(0.1) with h = 0.1., In the following second order initial value problems, obtain the solution by the fourth order, Runge-Kutta method., 8. Consider the second order initial value problem, y″ – 2y′ + 2y = e2t sin t, with y(0) = – 0.4 and y′(0) = – 0.6., Find y(0.2)., , (A.U. April/May 2003), , 9. Given y″ + y′ + y = 0, y(0) = 1, y′(0) = 0, find the value of y(0.1). (A.U. Nov./Dec. 2006), 10. y″ + 3y′ + 2y = et, with y(0) = 1 and y′(0) = 1. Find y(0.2) with h = 0.1., 11. y″ + 2y′ + y = tet, with y(0) = 0.5 and y′(0) = 0.8. Find y(0.2) with h = 0.2., 12. What are the values of k1 and l1 in the Runge-Kutta method of fourth order, to solve, y″ + xy′ + y = 0, y(0) = 1, y′(0) = 0., (A.U. April/May 2005), , 4.6, , MULTI STEP METHODS AND PREDICTOR-CORRECTOR METHODS, , In section 4.2, we have defined the explicit and implicit multi step methods for the solution of, the initial value problem, y′ = f (x, y), y(x0) = b0., , (4.66), , A general k-step explicit method can be written as, yi+1 = yi = hφ(xi–k+1, ..., xi–1, xi, yi–k+1, ..., yi–1, yi, h), , (4.67), , and a general k-step implicit method can be written as, yi+1 = yi = hφ(xi–k+1, ..., xi, xi+1, yi–k+1, ..., yi, yi+1, h)., , (4.68), , Remark 7 Multi step methods are not self starting, since a k-step multi step method requires, the k previous values yi, yi–1, ..., yi–k+1. The k values that are required for starting the application, of the method are obtained by using some single step method like Euler’s method, Taylor, series method or Runge-Kutta method, which is of the same or lower order than the order of, the multi step method.
Page 228 :
217, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , Let us construct a few multi step methods., Integrating the differential equation y′ = f(x, y) in the interval [xi, xi+1], we get, , z, , xi + 1, , xi, , dy, dx =, dx, , z, , xi + 1, , xi, , f ( x, y) dx ., , y( xi + 1 ) = y( xi ) +, , or, , z, , xi + 1, , xi, , f ( x, y) dx ., , (4.69), , To derive the methods, we approximate the integrand f(x, y) by a suitable interpolation, polynomial., In general, we may integrate the differential equation y′ = f(x, y) in the interval, [xi–m, xi+1]. We get, , z, , x i +1, , xi −m, , or, , dy, dx =, dx, , z, , x i +1, , f ( x , y ) dx, , x i −m, , y( xi + 1 ) = y( xi − m ) +, , For m = 0, we get (4.69)., , z, , xi + 1, , xi − m, , f ( x, y) dx ., , 4.6.1 Predictor Methods (Adams-Bashforth Methods), All predictor methods are explicit methods., We have k data values, (xi, fi)(xi–1–, fi–1), ..., (xi–k+1, fi–k+1). For this data, we fit the Newton’s, backward difference interpolating polynomial of degree k – 1 as (see equation (2.47) in, chapter 2), Pk–1(x) = f(xi + sh) = f(xi) + s∇f(xi) +, +, Note that, , s(s + 1) 2, ∇ f(xi) + ..., 2!, , s(s + 1)(s + 2) ... (s + k − 2) k− 1, f ( xi ) ., ∇, (k − 1) !, , (4.70), , s = [(x – xi)/h] < 0., , The expression for the error is given by, T.E. =, , s(s + 1)(s + 2) ... (s + k − 1) k (k), h f (ξ), (k) !, , (4.71), , where ξ lies in some interval containing the points xi, xi–1, ..., xi–k+1 and x. We replace f(x, y) by, Pk–1(x) in (4.69). The limits of integration in (4.69) become, for x = xi , s = 0 and for x = xi+1, s = 1., Also, dx = hds. We get, yi+1 = yi + h, , z LMN, 1, , 0, , fi + s∇fi +, , OP, Q, , 1, 1, s( s + 1)∇ 2 fi + s( s + 1)( s + 2)∇3 fi + ... ds, 2, 6
Page 229 :
218, , NUMERICAL METHODS, , z, , s dx =, , 1, ,, 2, , s(s + 1)(s + 2) ds =, , 9, ,, 4, , Now,, , z, , 1, , 0, , 1, , 0, , Hence, we have, , z, z, 1, , s( s + 1) ds =, , 0, , 1, , 0, , 5, ,, 6, , s(s + 1)(s + 2)(s + 3) ds =, , LM, N, , yi+1 = yi + h fi +, , 251, ., 30, , OP, Q, , 1, 5 2, 3, 251 4, ∇ fi +, ∇ fi + ∇ 3 fi +, ∇ fi + ... ., 2, 12, 8, 720, , (4.72), , These methods are called Adams-Bashforth methods., Using (4.71), we obtain the error term as, Tk = hk+1, = hk+1, , z, z, , s(s + 1)(s + 2) ... (s + k − 1) (k), f (ξ) ds, (k) !, , 1, , 0, 1, , g(s) f (k) (ξ) ds., , 0, , (4.73), , Since, g(s) does not change sign in [0, 1], we get by the mean value theorem, Tk = hk+1 f, where, , g(s) =, , (k), , (ξ1), , z, , 1, , 0, , g(s)ds,, , 0 < ξ1 < 1, , (4.74), , 1, [s(s + 1) ... (s + k – 1)]., k!, , Alternately, we write the truncation error as, T.E. = y(xn+1) – yn+1, Using Taylor series, we expand y(xn+1), yn+1 about xn, and simplify. The leading term, gives the order of the truncation error., Remark 8 From (4.74), we obtain that the truncation error is of order O(hk+1). Therefore, a kstep Adams-Bashforth method is of order k., By choosing different values for k, we get different methods., k = 1: We get the method, yi+1 = yi + hfi, , (4.75), , which is the Euler’s method. Using (4.74), we obtain the error term as, T1 =, , h2, h2, f ′(ξ 1 ) =, y′′(ξ 1 ) ., 2, 2, , Therefore, the method is of first order., k = 2: We get the method, yi+1 = yi + h, , LM f, N, , i, , +, , OP, Q, , LM, N, , 1, 1, ∇fi = yi + h fi + ( fi − fi −1 ), 2, 2, , OP, Q
Page 230 :
219, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , = yi +, , h, [3fi – fi–1]., 2, , (4.76), , For using the method, we require the starting values yi and yi–1., Using (4.74), we obtain the error term as, T2 =, , 5 3, 5 3, h f ′′( ξ 2 ) =, h y″ ′ (ξ 2 )., 12, 12, , Therefore, the method is of second order., k = 3: We get the method, , LM, N, L, = y + hMf, N, , yi+1 = yi + h fi +, , i, , = yi +, , i, , +, , 1, 5 2, ∇ fi +, ∇ fi, 2, 12, , OP, Q, , 1, 5, ( fi − f i − 1 ) +, ( fi − 2 f i − 1 + f i − 2 ), 2, 12, , h, [23fi – 16fi–1 + 5fi–2]., 12, , OP, Q, (4.77), , For using the method, we require the starting values yi , yi–1 and yi–2., Using (4.74), we obtain the error term as, T3 =, , 3 4 (3), 3 4 (4), h f (ξ3) =, h y (ξ3)., 8, 8, , Therefore, the method is of third order., k = 4: We get the method, , LM, N, L, = y + h Mf, N, , yi+1 = yi + h fi +, , i, , = yi +, , i, , +, , 1, 5 2, 3, ∇ fi +, ∇ fi + ∇ 3 fi, 2, 12, 8, , OP, Q, , 1, 5, 3, ( fi − fi − 1 ) +, ( fi − 2 fi − 1 + fi − 2 ) + ( fi − 3 fi − 1 + 3 fi − 2 − fi − 3 ), 2, 12, 8, , h, [55fi – 59fi–1 + 37fi–2 – 9fi–3]., 24, , OP, Q, , (4.78), , For using the method, we require the starting values yi , yi–1, yi–2 and yi–3., Using (4.74), we obtain the error term as, T4 =, , 251 5 b 4g, 251 5 (5), h f (ξ 4 ) =, h y (ξ 4 ) ., 720, 720, , Therefore, the method is of fourth order., Remark 9 The required starting values for the application of the Adams-Bashforth methods, are obtained by using any single step method like Euler’s method, Taylor series method or, Runge-Kutta method.
Page 231 :
220, , NUMERICAL METHODS, , Example 4.12 Find the approximate value of y(0.3) using the Adams-Bashforth method of, third order for the initial value problem, y′ = x2 + y2, y(0) = 1, with h = 0.1. Calculate the starting values using the corresponding Taylor series method with, the same step length., Solution We have, , f(x, y) = x2 + y2, x0 = 0, y0 = 1., , The Adams-Bashforth method of third order is given by, yi+1 = yi +, , h, [23fi – 16fi–1 + 5fi–2]., 12, , We need the starting values, y0, y1, y2. The initial condition gives y0 = 1., The third order Taylor series method is given by, yi+1 = yi + hyi′ +, , h2, h3, y i″ +, y i′″ ., 2, 6, , y′ = x2 + y2, y″ = 2x + 2yy′, y″′ = 2 + 2[yy″ + (y′)2]., , We have, , We obtain the following starting values., i = 0 : x0 = 0, y0 = 1, y0′ = 1, y0″ = 2, y0″′ = 8., y(0.1) ≈ y1 = y0 + 0.1 y0′ +, , 0.01, 0.001, y 0″ +, y 0′″, 2, 6, , = 1 + 0.1(1) + 0.005(2) +, , 0.001, (8) = 1.111333., 6, , i = 1: x1 = 0.1, y1 = 1.111333, y1′ = 1.245061,, y1″ = 2.967355, y1′″ = 11.695793., y(0.2) ≈ y2 = y1 + 0.1 y1′ +, , 0.01, 0.001, y1″ +, y1′″, 2, 6, , = 1.111333 + 0.1(1.245061) + 0.005 (2.967355) +, , 0.001, (11.695793), 6, , = 1.252625., Now, we apply the given Adams-Bashforth method. We have, x2 = 0.2, y2 = 1.252625, y2′ = f2 = 1.609069., For i = 2, we obtain, y(0.3) ≈ y3 = y2 +, = y2 +, , h, [23f2 – 16f1 + 5 f0], 12, 0.1, [23(1.609069) – 16(1.245061) + 5(1)] = 1.436688., 12
Page 232 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 221, , Example 4.13 Find the approximate value of y(0.4) using the Adams-Bashforth method of, fourth order for the initial value problem, y′ = x + y2, y(0) = 1, with h = 0.1. Calculate the starting values using the Euler’s method with the same step length., Solution We have f(x, y) = x + y2, x0 = 0, y0 = 1., The Adams-Bashforth method of fourth order is given by, yi+1 = yi +, , h, [55fi – 59fi–1 + 37fi–2 – 9fi–3]., 24, , We need the starting values, y0, y1, y2, y3. The initial condition gives y0 = 1., Euler’s method is given by, yi+1 = yi + h yi′ = yi + h fi., We obtain the following starting values., x0 = 0, y0 = 1, y0′ = f0 = 1., , i = 0:, , y(0.1) ≈ y1 = y0 + 0.1 y0′ = 1 + 0.1(1) = 1.1., i = 1:, , x1 = 0.1, y1 = 1.1, y1′ = f(0.1, 1.1) = 1.31., y(0.2) ≈ y2 = y1 + 0.1 y1′ = 1.1 + 0.1(1.31) = 1.231., , i=2:, , x2 = 0.2, y2 = 1.231, y2′ = f(0.2, 1.231) = 1.715361., y(0.3) ≈ y3 = y2 + 0.1 y2′ = 1.231 + 0.1(1.715361) = 1.402536., , Now, we apply the given Adams-Bashforth method. We have, x3 = 0.3, y3 = 1.402536, y3′ = f3 = 2.267107., For i = 3, we obtain, y(0.4) ≈ y4 = y3 +, , 0.1, [55 f3 – 59f2 + 37f1 – 9f0], 24, , = 1.402536 +, , 0.1, [55(2.267107) – 59(1.715361) + 37(1.31) – 9(1)], 24, , = 1.664847., 4.6.2 Corrector Methods, All corrector methods are implicit methods., 4.6.2.1 Adams-Moulton Methods, Consider the k + 1 data values, (xi+1, fi+1), (xi , fi), (xi–1, fi–1), ..., (xi–k+1, fi–k+1) which include the, current data point. For this data, we fit the Newton’s backward difference interpolating polynomial of degree k as (see equation (2.47) in chapter 2)
Page 233 :
222, , NUMERICAL METHODS, , Pk(x) = f(xi + sh) = f(xi+1) + (s – 1) ∇f(xi+1) +, +, where, , (s − 1) s, ∇2 f(xi+i) + ..., 2!, , (s − 1) s(s + 1)(s + 2) ... (s + k − 2) k, ∇ f ( xi + 1 ), (k) !, , (4.79), , s = [(x – xi)/h] < 0., , The expression for the error is given by, T.E. =, , (s − 1)s(s + 1)(s + 2) ... (s + k − 1) k+1 (k+1), h, f, (ξ), (k + 1) !, , (4.80), , where ξ lies in some interval containing the points xi+1, xi , ..., xn–k+1 and x. We replace f(x, y) by, Pk(x) in (4.69). The limits of integration in (4.69) become, for x = xi, s = 0, and for x = xi+1, s = 1., Also, dx = hds. We get, , z LMN, 1, , yi+1 = yi + h, , +, , Now,, , z, z, z, , 1, , 0, , 1, , 0, 1, , 0, , ( s − 1) ds = −, , 0, , fi +1 + ( s − 1) ∇fi +1 +, , 1, ( s − 1)s∇ 2 fi +1, 2, , OP, Q, , 1, ( s − 1)s( s + 1)∇3 fi +1 + ... ds, 6, , z, , 1, ,, 2, , 1, , 0, , ( s − 1)s ds =, , Ls s O, (s − 1) s(s + 1) ds = M − P, N4 2Q, 4, , (s − 1) s(s + 1)( s + 2) ds = −, , 2 1, 0, , =−, , LM s − s OP, MN 3 2 PQ, 3, , 2, , 1, , =−, 0, , 1, 6, , 1, ., 4, , 19, ., 30, , Hence, we have, , LM, N, , yi+1 = yi + h fi + 1 −, , OP, Q, , 1, 1 2, 1 3, 19 4, ∇ fi + 1 −, ∇ fi + 1 −, ∇ fi + 1 −, ∇ fi + 1 − ..., 2, 12, 24, 720, , (4.81), , These methods are called Adams-Moulton methods., Using (4.80), we obtain the error term as, Tk = hk+2, = hk+2, , z, z, , 1, , 0, 1, , 0, , ( s − 1) s(s + 1)( s + 2) ... ( s + k − 1) (k+1), f, (ξ) ds, ( k + 1) !, g( s) f ( k+1) (ξ) ds, , (4.82)
Page 234 :
223, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , where, , g(s) =, , 1, [(s – 1)s(s + 1) ... (s + k – 1)]., +, (k 1) !, , Since g(s) does not change sign in [0, 1], we get by the mean value theorem, Tk = hk+2 f (k+1) (ξ1), , z, , 1, , 0, , g( s) ds , 0 < ξ1 < 1., , (4.83), , Remark 10 From (4.83), we obtain that the truncation error is of order O(hk+2). Therefore, a, k-step Adams-Moulton method is of order k + 1., By choosing different values for k, we get different methods., k = 0 : We get the method, yi+1 = yi + hfi +1, , (4.84), , which is the backward Euler’s method. Using (4.83), we obtain the error term as, T1 = –, , h2, h2, f ′ (ξ 1 ) = −, y ′′(ξ 1 ) ., 2, 2, , Therefore, the method is of first order., k = 1: We get the method, , LM, N, , yi+1 = yi + h fi + 1 −, = yi +, , OP, Q, , LM, N, , 1, 1, ∇ fi + 1 = y i + h fi + 1 − ( fi + 1 − f i ), 2, 2, , h, [ f + f ]., 2 i+1 i, , OP, Q, (4.85), , This is also a single step method and we do not require any starting values. This method, is also called the trapezium method., Using (4.83), we obtain the error term as, T2 = –, , 1 3, 1 3, h f ″ (ξ2) = –, h y′″(ξ2)., 12, 12, , Therefore, the method is of second order., k = 2: We get the method, , LM, N, L, = y + h Mf, N, , yi + 1 = yi + h f i +1 −, , = yi +, , i +1, , −, , 1, 1 2, ∇ fi + 1 −, ∇ fi + 1, 2, 12, , OP, Q, , 1, 1, ( f i +1 − f i ) −, ( f i +1 − 2 fi + f i −1 ), 2, 12, , h, [5fi + 1 + 8fi – fi – 1]., 12, , OP, Q, (4.86)
Page 235 :
224, , NUMERICAL METHODS, , For using the method, we require the starting values, , y i , y i−1., , Using (4.83), we obtain the error term as, , 1 4 (3), 1 4 (4 ), h f (ξ 3 ) = −, h y (ξ 3 ) ., 24, 24, , T3 = –, , Therefore, the method is of third order., k = 3: We get the method, , LM, N, L, = y + h Mf, N, , yi+1 = yi + h fi + 1 −, , i, , –, , −, , i +1, , 1, 1 2, 1 3, ∇ fi + 1 −, ∇ fi + 1 −, ∇ fi + 1, 2, 12, 24, , 1, 1, ( fi + 1 − f i ) −, ( fi +1 − 2fi + fi −1 ), 2, 12, , 1, (f – 3fi + 3fi–1 – fi–2), 24 i+1, , = yi +, , OP, Q, , OP, Q, , h, [9fi+1 + 19fi – 5fi–1 + fi–2]., 24, , (4.87), , For using the method, we require the starting values yi, yi–1, yi–2., Using (4.83), we obtain the error term as, , 19 5 ( 4), 19 5 (5), h f (ξ 4 ) = −, h y (ξ 4 ) ., 720, 720, , T4 = –, , Therefore, the method is of fourth order., 4.6.2.2 Milne-Simpson Methods, To derive the Milne’s methods, we integrate the differential equation y′ = f(x, y) in the interval, [xi–1, xi+1]. We get, , z, , x i +1, , x i −1, , or, , dy, dx =, dx, , z, , x i +1, , x i −1, , f ( x , y ) dx ., , z, , y(xi+1) = y(xi–1) +, , x i +1, , x i −1, , f ( x , y ) dx ., , (4.88), , To derive the methods, we use the same approximation, follow the same procedure and, steps as in Adams-Moulton methods. The interval of integration for s is [– 1, 1]. We obtain, yi+1 = yi–1 + h, , +, , z LMN, 1, , 0, , fi +1 + ( s − 1) ∇fi +1 +, , OP, Q, , 1, ( s − 1)s∇ 2 fi +1, 2, , 1, ( s − 1)s( s + 1)∇3 fi +1 + ... ds, 6
Page 236 :
225, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , z, , Now,, , z, , 1, , −1, , 1, , −1, , z, , (s – 1) ds = – 2,, , (s – 1)s(s + 1) ds = 0,, , Hence, we have, , z, , 1, , 0, , 1, , −1, , (s – 1)s ds =, , 2, ,, 3, , (s – 1)s(s + 1)(s + 2) ds = –, , LM, N, , yi+1 = yi–1 + h 2 fi + 1 − 2∇fi + 1 +, , 24, ., 90, , OP, Q, , 1 2, 1 4, ∇ fi + 1 + (0) ∇ 3 fi + 1 −, ∇ fi + 1 − ... ., 3, 90, , (4.89), , These methods are called Milne’s methods., The case k = 2, is of interest for us. We obtain the method as, , LM, N, L, + h M2 f, N, , yi+1 = yi–1 + h 2 fi + 1 − 2∇fi + 1 +, = yi–1, , = yi–1 +, , i+ 1, , 1 2, ∇ fi + 1, 3, , − 2( fi + 1 − fi ) +, , OP, Q, , 1, ( fi + 1 − 2 fi + fi − 1 ), 3, , h, [f + 4fi + fi–1)]., 3 i+1, , OP, Q, (4.90), , This method is also called the Milne-Simpson’s method., For using the method, we require the starting values yi, yi–1., The error term is given by, Error = –, , 1 5 ( 4), 1 5 (5 ), h f (ξ) = −, h y (ξ) ., 90, 90, , Therefore, the method is of fourth order., Remark 11 The methods derived in this section are all implicit methods. Therefore, we need, to solve a nonlinear algebraic equation for obtaining the solution at each point. Hence, these, methods are not used as such but in combination with the explicit methods. This would give, rise to the explicit-implicit methods or predictor-corrector methods, which we describe in the, next section., 4.6.2.3 Predictor-Corrector Methods, In the previous sections, we have derived explicit single step methods (Euler’s method, Taylor, series methods and Runge-Kutta methods), explicit multi step methods (Adams-Bashforth, methods) and implicit methods (Adams-Moulton methods, Milne-Simpson methods) for the, solution of the initial value problem y′ = f(x, y), y(x0) = y0. If we perform analysis for numerical, stability of these methods (we shall discuss briefly this concept in the next section), we find, that all explicit methods require very small step lengths to be used for convergence. If the, solution of the problem is required over a large interval, we may need to use the method, thousands or even millions of steps, which is computationally very expensive. Most implicit, methods have strong stability properties, that is, we can use sufficiently large step lengths for, computations and we can obtain convergence. However, we need to solve a nonlinear alge-
Page 237 :
226, , NUMERICAL METHODS, , braic equation for the solution at each nodal point. This procedure may also be computationally, expensive as convergence is to be obtained for the solution of the nonlinear equation at each, nodal point. Therefore, we combine the explicit methods (which have weak stability properties) and implicit methods (which have strong stability properties) to obtain new methods., Such methods are called predictor-corrector methods or P-C methods., Now, we define the predictor-corrector methods. We denote P for predictor and C for, corrector., P: Predict an approximation to the solution yi+1 at the current point, using an explicit, p), method. Denote this approximation as yi(+1, ., p), C: Correct the approximation yi(+1, , using a corrector, that is, an implicit method. Denote, c), this corrected value as yi(+1, . The corrector is used 1 or 2 or 3 times, depending on the, orders of explicit and implicit methods used., , Remark 12 The order of the predictor should be less than or equal to the order of the corrector., If the orders of the predictor and corrector are same, then we may require only one or two, corrector iterations at each nodal point. For example, if the predictor and corrector are both of, fourth order, then the combination (P-C method) is also of fourth order and we may require, one or two corrector iterations at each point. If the order of the predictor is less than the order, of the corrector, then we require more iterations of the corrector. For example, if we use a first, order predictor and a second order corrector, then one application of the combination gives a, result of first order. If corrector is iterated once more, then the order of the combination increases, by one, that is the result is now of second order. If we iterate a third time, then the truncation, error of the combination reduces, that is, we may get a better result. Further iterations may, not change the results., We give below a few examples of the predictor-corrector methods., Example 1, Predictor P: Euler method:, yn( p+)1 = yn + hf ( xn , yn ) ., , (4.91), , h2, h2, f ′ (ξ 1 ) =, y ′′(ξ 1 ) ., 2, 2, Corrector C: Backward Euler method (4.84):, , Error term =, , yn( c+) 1 = yn + hf ( xn +1 , yn( p+)1 ) ., h2, h2, f ′ (ξ 1 ) = −, y ′′(ξ 1 ) ., 2, 2, Both the predictor and corrector methods are of first order. We compute, , Error term = –, , yn(0+)1 = yn + hf ( xn , yn ) ., yn(1+) 1 = yn + hf ( xn +1 , yn(0+)1 ) ., , yn(2+)1 = yn + hf ( xn + 1, yn(1+) 1 ), etc., , (4.92)
Page 239 :
228, , NUMERICAL METHODS, , Predictor P: Adams-Bashforth method of fourth order., , 4h, [ 2 f i − fi − 1 + 2 f i − 2 ] ., 3, , yi(+p1) = yi − 3 +, Error term =, , (4.97), , 14 5 ( 4 ), 14 5 ( 5), h f (ξ) =, h y (ξ) ., 45, 45, , The method requires the starting values yi, yi–1, yi–2 and yi–3., Corrector C: Milne-Simpson’s method of fourth order., , yi(+c)1 = yi − 1 +, Error term = –, , h, [ f ( xi + 1, yi(+p1) ) + 4 fi + fi −1 )] ., 3, , (4.98), , 1 5 (4), 1 5 (5 ), h f (ξ) = −, h y (ξ) ., 90, 90, , The method requires the starting values yi, yi–1., The combination requires the starting values yi, yi–1, yi–2 and yi–3. That is, we require, the values y0, y1, y2, y3. Initial condition gives the value y0., Remark 13 Method (4.97) is obtained in the same way as we have derived the Adams-Bashforth, methods. Integrating the given differential equation y′ = f(x, y) on the interval, (xi–3 , xi+1), we obtain, , z, , x i +1, , xi −3, , or, , dy, dx =, dx, , z, , x i +1, , xi −3, , f ( x , y ) dx, , y(xi+1) = y(xi–3) +, , z, , x i +1, , xi −3, , f ( x , y ) dx ., , Replace the integrand on the right hand side by the same backward difference polynomial (4.70) and derive the method in the same way as we have done in deriving the explicit, Adams-Bashforth methods. We obtain the method as, , LM, N, , y i +1 = yi −3 + h 4 fi − 4∇fi +, , OP, Q, , 8 2, 14 4, ∇ fi + ( 0)∇3 fi +, ∇ fi + ... ., 3, 35, , Retaining terms up to ∇ 3fi , we obtain the method, , LM, N, L, + h M4 f, N, , yi + 1 = yi −3 + h 4 fi − 4∇fi +, , = yi − 3, , = yi −3 +, , i, , 8 2, ∇ fi + (0) ∇ 3 fi, 3, , − 4 ( fi − fi − 1 ) +, , OP, Q, , 8, ( fi − 2 fi − 1 + fi − 2, 3, , 4h, [2 f i − f i − 1 + 2 f i − 2 ], 3, , OP, Q, , (4.99)
Page 240 :
229, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , The error term is given by, T.E. =, , 14 5 ( 4), 14 5 (5), h f (ξ) =, h y (ξ) ., 45, 45, , Therefore, the method is of fourth order., Example 4.14 Using the Adams-Bashforth predictor-corrector equations, evaluate y(1.4), if y, satisfies, , dy y, 1, + = 2, dx x x, and y(1) = 1, y(1.1) = 0.996, y(1.2) = 0.986, y(1.3) = 0.972., , (A.U. Nov./Dec. 2006), , Solution The Adams-Bashforth predictor-corrector method is given by, Predictor P: Adams-Bashforth method of fourth order., , h, [55 fi − 59 fi −1 + 37 fi − 2 − 9 fi − 3 ]., 24, , yi(+p1) = yi +, , The method requires the starting values yi, yi–1, yi–2 and yi–3., Corrector C: Adams-Moulton method of fourth order., , yi(+c)1 = yi +, , h, [9 f ( xi + 1, yi(+p1) ) + 19 fi − 5 fi − 1 + fi − 2 ], 24, , The method requires the starting values yi, yi–1, yi–2., The combination requires the starting values yi, yi–1, yi–2 and yi–3. That is, we require, the values y0, y1, y2, y3. With h = 0.1, we are given the values, y(1) = 1, y(1.1) = 0.996, y(1.2) = 0.986, y(1.3) = 0.972., We have, , f(x, y) =, , 1, x, , 2, , −, , y, ., x, , Predictor application, For i = 3, we obtain, , y4(0) = y4( p) = y3 +, We have, , h, [55 f3 − 59 f2 + 37 f1 − 9 f0 ], 24, , f0 = f(x0, y0) = f(1, 1) = 1 – 1 = 0,, f1 = f(x1, y1) = f(1.1, 0.996) = – 0.079008,, f2 = f(x2, y2) = f(1.2, 0.986) = – 0.127222,, f3 = f(x3, y3) = f(1.3, 0.972) = – 0.155976., y 4( 0) = 0.972 +, , 01, ., [ 55( − 0.155976) − 59( − 0127222, ., ) + 37( − 0.079008 ) − 9( 0 )], 24, , = 0.955351.
Page 241 :
230, , NUMERICAL METHODS, , Corrector application, Now,, , f ( x4 , y4(0) ) = f(1.4, 0.955351) = – 0.172189., , First iteration, y 4(1) = y 4( c ) = y 3 +, , h, [ 9f ( x 4 , y 4( 0 ) ) + 19f3 − 5f 2 + f1 ], 24, , = 0.972 +, , 0.1, [9(– 0.172189) + 19(– 0.155976) – 5(– 0.127222), 24, , + (– 0.079008)] = 0.955516., Second iteration, f ( x4 , y4( 1) ) = f(1.4, 0.955516) = – 0.172307., , y4(2) = y3 +, , h, [9 f ( x4 , y4(1) ) + 19 f3 − 5 f2 + f1 ], 24, , = 0.972 +, , 0.1, [9(– 0.172307) + 19(– 0.155976) – 5(– 0.127222), 24, , + (– 0.079008)] = 0.955512., Now,, , | y4( 2) − y4( 1) | = | 0.955512 – 0.955516 | = 0.000004., , Therefore,, , y(1.4) = 0.955512. The result is correct to five decimal places., , Example 4.15 Given y′ = x3 + y, y(0) = 2, the values y(0.2) = 2.073, y(0.4) = 2.452, and y(0.6), = 3.023 are got by Runge-Kutta method of fourth order. Find y(0.8) by Milne’s predictor-corrector, method taking h = 0.2., (A.U. April/May 2004), Solution Milne’s predictor-corrector method is given by, Predictor P: Adams-Bashforth method of fourth order., , yi(+p1) = yi − 3 +, , 4h, [ 2 f i − fi − 1 + 2 f i − 2 ] ., 3, , Corrector C: Milne-Simpson’s method of fourth order., , yi(+c)1 = yi − 1 +, , h, [ f ( xi + 1 , yi(+p1) ) + 4 fi + fi − 1 ] ., 3, , The method requires the starting values yi, yi–1, yi–2 and yi–3. That is, we require the, values y0, y1, y2, y3. Initial condition gives the value y0., We are given that, f(x, y) = x3 + y, x0 = 0, y0 = 2, y(0.2) = y1 = 2.073,, y(0.4) = y2 = 2.452, y(0.6) = y3 = 3.023.
Page 242 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , Predictor application, For i = 3, we obtain, , 4(0.2), [2 f3 − f 2 + 2 f1 ] ., 3, f0 = f(x0, y0) = f(0, 2) = 2,, , y4(0) = y4( p) = y0 +, We have, , f1 = f(x1, y1) = f(0.2, 2.073) = 2.081,, f2 = f(x2, y2) = f(0.4, 2.452) = 2.516,, f3 = f(x3, y3) = f(0.6, 3.023) = 3.239., , y4(0) = 2 +, , 0.8, [2(3.239) – 2.516 + 2(2.081)] = 4.1664., 3, , Corrector application, First iteration For i = 3, we get, , y 4(1) = y2 +, , 0.2, [ f ( x 4 , y 4( 0 ) ) + 4 f3 + f2 ], 3, , Now, f ( x4 , y4(0) ) = f(0.8, 4.1664) = 4.6784., , y4(1) = 2.452 +, , 0.2, [4.6784 + 4(3.239) + 2.516] = 3.79536., 3, , Second iteration, y 4( 2 ) = y 2 +, , 0.2, [ f ( x 4 , y 4(1) ) + 4 f3 + f2 ], 3, , Now, f ( x4 , y4(1) ) = f(0.8, 4.6784) = 4.30736., , y4(2) = 2.452 +, We have, , 0.2, [4.30736 + 4(3.239) + 2.516] = 3.770624., 3, , | y4( 2) − y4( 1) | = | 3.770624 – 3.79536 | = 0.024736., , The result is accurate to one decimal place., Third iteration, y 4( 3) = y 2 +, , Now,, , 0.2, [ f ( x 4 , y 4( 2 ) ) + 4 f3 + f 2 ], 3, , f ( x4 , y4(2) ) = f (0.8, 3.770624) = 4.282624., y4(3) = 2.452 +, , We have, , 0.2, [4.282624 + 4(3.239) + 2.516] = 3.768975., 3, , | y4(3) − y4( 2) | = | 3.768975 – 3.770624 | = 0.001649., , The result is accurate to two decimal places., , 231
Page 243 :
232, , NUMERICAL METHODS, , Fourth iteration, y 4( 4 ) = y 2 +, , Now,, , 0.2, [ f ( x 4 , y 4( 3 ) ) + 4 f3 + f 2 ], 3, , f ( x4 , y4(3) ) = f(0.8, 3.76897) = 4.280975., , y4(4) = 2.452 +, , 0.2, [4.280975 + 4(3.239) + 2.516] = 3.768865., 3, , We have | y4( 4) − y4(3) | = | 3.768865 – 3.768975 | = 0.000100., The result is accurate to three decimal places., The required result can be taken as y(0.8) = 3.7689., Example 4.16 Using Milne’s predictor-corrector method, find y(0.4) for the initial value problem, y′ = x2 + y2, y(0) = 1, with h = 0.1., Calculate all the required initial values by Euler’s method. The result is to be accurate to three, decimal places., Solution Milne’s predictor-corrector method is given by, Predictor P: Adams-Bashforth method of fourth order., yi(+p1) = yi − 3 +, , 4h, [ 2 fi − fi − 1 + 2 fi − 2 ] ., 3, , Corrector C: Milne-Simpson’s method of fourth order., y i( +c1) = y i −1 +, , h, [ f ( x i +1 , y i( +p1) ) + 4 f i + f i −1 ] ., 3, , The method requires the starting values yi, yi–1, yi–2 and yi–3. That is, we require the, values y0, y1, y2, y3. Initial condition gives the value y0., We are given that, f(x, y) = x2 + y2, x0 = 0, y0 = 1., Euler’s method gives, yi + 1 = yi + hf ( xi , yi ) = yi + 0.1( xi2 + yi2 ) ., , With x0 = 0, y0 = 1, we get, y1 = y0 + 0.1 ( x02 + y02 ) = 1.0 + 0.1 (0 + 1.0) = 1.1., y2 = y1 + 0.1 ( x12 + y12 ) = 1.1 + 0.1 (0.01 + 1.21) = 1.222., y3 = y2 + 0.1 ( x22 + y22 ) = 1.222 + 0.1[0.04 + (1.222)2] = 1.375328.
Page 244 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , Predictor application, For i = 3, we obtain, , y4(0) = y4( p) = y0 +, We have, , 4(0.1), [2 f3 − f2 + 2 f1 ], 3, , f1 = f(x1, y1) = f(0.1, 1.1) = 1.22,, f2 = f(x2, y2) = f(0.1, 1.222) = 1.533284,, f3 = f(x3, y3) = f(0.3, 1.375328) = 1.981527., , y4(0) = 1.0 +, , 0.4, [2(1.981527) – 1.533284 + 2(1.22)] = 1.649303., 3, , Corrector application, First iteration For i = 3, we get, y 4(1) = y 2 +, , Now,, , 01, ., [ f ( x 4 , y 4( 0 ) ) + 4 f3 + f 2 ], 3, , f ( x4 , y4(0) ) = f(0.4, 1.649303) = 2.880200., , y4(1) = 1.222 +, , 0.1, [2.880200 + 4(1.981527) + 1.533284] = 1.633320., 3, , Second iteration, y 4( 2) = y 2 +, , Now,, , 01, ., [ f ( x 4 , y 4(1) ) + 4 f3 + f 2 ], 3, , f ( x4 , y4(1) ) = f(0.4, 1.633320) = 2.827734., y4( 2) = 1.222 +, , 0.1, [2.827734 + 4(1.981527) + 1.533284] = 1.631571., 3, , We have | y4( 2) − y4( 1) | = | 1.631571 – 1.633320 | = 0.001749., The result is accurate to two decimal places., Third iteration, y 4( 3) = y 2 +, , Now,, , 01, ., [ f ( x 4 , y 4( 2 ) ) + 4 f3 + f 2 ], 3, , f ( x4 , y4(2) ) = f(0.4, 1.631571) = 2.822024., y4(3) = 1.222 +, , 0.1, [2.822024 + 4(1.981527) + 1.533284] = 1.631381., 3, , We have | y4(3) − y4( 2) | = | 1.631381 – 1.631571 | = 0.00019., The result is accurate to three decimal places., The required result can be taken as y(0.4) ≈ 1.63138., , 233
Page 245 :
234, , NUMERICAL METHODS, , REVIEW QUESTIONS, 1. Are the multi step methods self starting ?, Solution Multi step methods are not self starting, since a k-step multi step method, requires the k previous values yi, yi–1, ..., yi–k+1. The k values that are required for starting the application of the method are obtained using some single step method like Euler, method, Taylor series method or Runge-Kutta method, which is of the same or lower, order than the order of the multi step method., 2. Why do we require predictor-corrector methods for solving the initial value problem, y′ = f(x, y), y(x0) = y0 ?, Solution If we perform analysis for numerical stability of single or multi step methods,, we find that all explicit methods require very small step lengths to be used for convergence. If the solution of the problem is required over a large interval, we may need to, use the method, thousands or even millions of steps, which is computationally very, expensive. Most implicit methods have strong stability properties, that is, we can use, sufficiently large step lengths for computations and we can obtain convergence. However, we need to solve a nonlinear algebraic equation for the solution at each nodal, point. This procedure may also be computationally expensive as convergence is to be, obtained for the solution of the nonlinear equation at each nodal point. Therefore, we, combine the explicit methods (which have weak stability properties) and implicit methods (which have strong stability properties) to obtain new methods. Such methods are, called predictor-corrector methods., 3. What are predictor-corrector methods for solving the initial value problem, y′ = f (x, y), y(x0) = y0 ? Comment on the order of the methods used as predictors and, correctors., Solution We combine the explicit methods (which have weak stability properties) and, implicit methods (which have strong stability properties) to obtain new methods. Such, methods are called predictor-corrector methods. We denote P for predictor and C for, corrector., P: Predict an approximation to the solution yi+1 at the current point, using an explicit, p), method. Denote this approximation as yi(+1, ., , p), C: Correct the approximation yi(+1, , using a corrector, that is, an implicit method. Denote, c), this corrected value as yi(+1, . The corrector is used 1 or 2 or 3 times, depending on the, , orders of explicit and implicit methods used., The order of the predictor should be less than or equal to the order of the corrector. If, the orders of the predictor and corrector are same, then we may require only one or two, corrector iterations at each nodal point. For example, if the predictor and corrector are, both of fourth order, then the combination (P-C method) is also of fourth order and we, may require one or two corrector iterations at each point. If the order of the predictor is, less than the order of the corrector, then we require more iterations of the corrector. For, example, if we use a first order predictor and a second order corrector, then one
Page 246 :
INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 235, , application of the combination gives a result of first order. If corrector is iterated once, more, then the order of the combination increases by one, that is, the result is now of, second order. If we iterate a third time, then the truncation error of the combination, reduces, that is, we may get a better result. Further iterations may not change the, results., 4. Write Adams-Bashforth predictor-corrector method for solving the initial value problem, y′ = f(x, y), y(x0) = b0. Comment on the order and the required starting values., Solution The Adams-Bashforth predictor-corrector method is given by, Predictor P: Adams-Bashforth method of fourth order., , yi(+p1) = yi +, , h, [55fi – 59fi–1 + 37fi–2 – 9fi–3]., 24, , 251 5 ( 4), 251 5 ( 5), h f (ξ 4 ) =, h y (ξ 4 ) ., 720, 720, The method requires the starting values yi, yi–1, yi–2 and yi–3., Error term =, , Corrector C: Adams-Moulton method of fourth order., , yi(+c)1 = yi +, Error term = –, , h, [9 f ( xi + 1, yi(+p1) ) + 19 fi − 5 fi − 1 + fi − 2 ] ., 24, , 19 5 ( 4 ), 19 5 ( 5 ), h f, h y (ξ4 ) ., (ξ4 ) = −, 720, 720, , The method requires the starting values yi, yi–1, yi–2., The combination requires the starting values yi, yi–1, yi–2 and yi–3. That is, we require, the values y0, y1, y2, y3. Initial condition gives the value y0., 5. Write the Milne’s predictor-corrector method for solving the initial value problem, y′ = f(x, y), y(x0) = b0. Comment on the order and the required starting values., Solution Milne’s predictor-corrector method is given by, Predictor P: Adams-Bashforth method of fourth order, , yi( +p1) = y i −3 +, Error term =, , 4h, [ 2fi − fi −1 + 2fi −2 ] ., 3, , 14 5 ( 4), 14 5 (5), h f (ξ) =, h y (ξ) ., 45, 45, , The method requires the starting values yi, yi–1, yi–2 and yi–3., Corrector C: Milne-Simpson’s method of fourth order, , y i( +c1) = y i −1 +, Error term = –, , h, [ f ( x i +1 , y i( +p1) ) + 4 fi + fi −1 ], 3, , 1 5 (4 ), 1 5 (5), h f (ξ) = −, h y (ξ) ., 90, 90, , The method requires the starting values yi, yi–1.
Page 247 :
236, , NUMERICAL METHODS, , The combination requires the starting values yi, yi–1, yi–2 and yi–3. That is, we require, the values y0, y1, y2, y3. Initial condition gives the value y0., 6. How many prior values are required to predict the next value in Adams-BashforthMoulton method ?, Solution The Adams-Bashforth-Moulton predictor-corrector method requires four, starting values yi, yi–1, yi–2 and yi–3. That is, we require the values y0, y1, y2, y3. Initial, condition gives the value y0., 7. How many prior values are required to predict the next value in Milne’s predictorcorrector method ?, Solution The Milne’s predictor-corrector method requires four starting values yi, yi–1,, yi–2 and yi–3. That is, we require the values y0, y1, y2, y3. Initial condition gives the value, y0 ., 8. What are the orders of the predictor and corrector in Adams-Bashforth-Moulton predictor-corrector method ?, Solution Both the predictor and corrector are of fourth order, that is, truncation error, is of order O(h5) in each case., 9. What are the orders of the predictor and corrector in Milne’s predictor-corrector method ?, Solution Both the predictor and corrector are of fourth order, that is, truncation error, is of order O(h5) in each case., , EXERCISE 4.4, 1. Using the Runge-Kutta method of order 4, find y for x = 0.1, 0.2, 0.3 given that, , dy, = xy + y2 , y(0) = 1, dx, and also find the solution at x = 0.4 by Milne’s method., , (A.U. Nov./Dec. 2003), , 2. Use Milne’s method to find y(4.4) given that, 5xy′ + y2 – 2 = 0, y(4) = 1, y(4.1) = 1.0049, y(4.2) = 1.0097, y(4.3) = 1.0143., (A.U. Nov./Dec. 2004), x2,, , is satisfied by y(0) = 1, y(0.2) = 1.12186, y(0.4), 3. The differential equation y′ = y –, = 1.46820, y(0.6) = 1.7359. Compute the value of y(0.8) by Milne’s predictor-corrector, formula., (A.U. Nov./Dec. 2006), 4. Solve y′ = x – y2, 0 ≤ x ≤ 1, y(0) = 0, y(0.2) = 0.02, y(0.4) = 0.0795, y(0.6) = 0.1762 by, Milne’s method to find y(0.8) and y(1)., (A.U. April/May 2005), 5. Determine the value of y(0.4) using Milne’s method given that y′ = xy + y2, y(0) = 1. Use, Taylor series method to get the values of y(0.1), y(0.2) and y(0.3)., (A.U. Nov./Dec. 2003), 6. Given that y′ + xy + y = 0, y(0) = 1, obtain y for x = 0.1, 0.2, and 0.3 by Taylor series, method and find the solution for y(0.4) by Milne’s method., (A.U. Nov./Dec. 2003)
Page 248 :
237, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 7. Compute the first 3 steps of the initial value problem y′ = (x – y)/2, y(0) = 1.0 by Taylor, series method and next step by Milne’s method with step length h = 0.1., (A.U. Nov./Dec. 2005), 8. Solve the initial value problem, y′ = (1 + x2)(y – 1), y(1) = 0,, , x ∈ [1.0, 1.4], , with h = 0.1 using the Milne’s predictor corrector method. Perform two iterations of the, corrector. Compute the starting values using the Euler method with the same step size., 9. Solve the initial value problem, y′ = y – x2, y(0) = 1, x ∈ [0.0, 0.4], with h = 0.1 using the Adams-Bashforth predictor-corrector method. Perform two, iterations of the corrector. Compute the starting values using the Taylor series method, of the same order. Also, compare these solutions with the exact solution y(x) = x2 + 2x, + 2 – ex., 10. Consider the initial value problem, dy, = y − x 2 + 1 , y(0) = 0.5, dx, , (A.U. April/May 2003), , Using the Adams-Bashforth predictor-corrector method, find f(0.8)., 11. Given, , dy, ,, ., , y(1.3) = 1979, ., = x 2 (1 + y), y(1) = 1, y(1.1) = 1.233, y(1.2) = 1548, dx, , evaluate y(1.4) by Adams-Bashforth method., , (A.U. Nov./Dec. 2004), , 12. Solve y′ = 1 – y with the initial condition x = 0, y = 0, using Euler’s algorithm and, tabulate the solutions at x = 0.1, 0.2, 0.3, 0.4. Using these results find y(0.5), using, Adams-Bashforth predictor-corrector method., (A.U. May/June 2006), , 4.7, , STABILITY OF NUMERICAL METHODS, , In any initial value problem, we require solution for x > x0 and usually up to a point x = b. The, step length h for application of any numerical method for the initial value problem must be, properly chosen. The computations contain mainly two types of errors: truncation error and, round-off error. Truncation error is in the hand of the user. It can be controlled by choosing, higher order methods. Round-off errors are not in the hands of the user. They can grow and, finally destroy the true solution. In such case, we say that the method is numerically unstable., This happens when the step length is chosen larger than the allowed limiting value. All explicit, methods have restrictions on the step length that can be used. Many implicit methods have no, restriction on the step length that can be used. Such methods are called unconditionally stable, methods., The behaviour of the solution of the given initial value problem is studied by considering the linearized form of the differential equation y′ = f (x, y). The linearized form of the, initial value problem is given by y′ = λ y, λ < 0, y(x0) = y0. The single step methods are applied, to this differential equation to obtain the difference equation yi+1 = E(λh)yi, where E(λh) is
Page 249 :
238, , NUMERICAL METHODS, , called the amplification factor. If | E(λh) | < 1, then all the errors (round-off and other errors), decay and the method gives convergent solutions. We say that the method is stable. This, condition gives a bound on the step length h that can be used in the computations. We have, the following conditions for stability of the single step methods that are considered in the, previous sections., 1. Euler method: – 2 < λh < 0., 2. Runge-Kutta method of second order: – 2 < λh < 0., 3. Classical Runge-Kutta method of fourth order: – 2.78 < λh < 0., 4. Backward Euler method: Stable for all h, that is, – ∞ < λh < 0. (Unconditionally, stable method)., Similar stability analysis can be done for the multi step methods. We have the following stability intervals (condition on λ h), for the multi step methods that are considered in the, previous sections., Order, , Adams-Bashforth methods, , Adams-Moulton methods, , 1, , (– 2, 0), , (– ∞, 0), , 2, , (– 1, 0), , (– ∞, 0), , 3, , (– 0.5, 0), , (– 6, 0), , 4, , (– 0.3, 0), , (– 3, 0), , Thus, we conclude that a numerical method can not be applied as we like to a given, initial value problem. The choice of the step length is very important and it is governed by the, stability condition., For example, if we are solving the initial value problem y′ = – 100y, y(x0) = y0, by Euler, method, then the step length should satisfy the condition – 2 < λh < 0 or – 2 < – 100h < 0, or, h < 0.02., The predictor-corrector methods also have such strong stability conditions., , 4.8, , ANSWERS AND HINTS, , Exercise 4.1, 1. 0.1, 0.22; 0.11, 0.24205; 0.11, 0.24205., 2. 0.9, 0.819; 0.90975, 0.834344; 0.9095, 0.833962., 3. h = 0.1: 1.573481; h = 0.2: 1.496. Extrapolated value = 2(1.573481) – 1.496 =1.650962., 4. h = 0.1: 3.848948; h = 0.2: 3.137805. Extrapolated value = 2(3.848948) – 3.137805, = 4.560091., 2, 2, 5. | Error | ≤ (h2/2) max | y ′′( x)|= (h /2) max |1 − sin y|≤ h . For h = 0.2, | Error | ≤, 0 ≤ x ≤ 0.2, , 0.05., 6. y1 = 1.252533, y2 = 1.693175., , 0 ≤ x ≤ 0.2
Page 250 :
239, , INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS, , 7. Taylor series method: 1.355, 1.855475, 2.551614, 3.510921. Heun’s method: 1.355,, 1.855475, 2.551614, 3.510921., 8. Use Taylor series method of fourth order 1.508933, 2.305006., 9. Use Taylor series method of fourth order 1.46555, 2.128321., In Problems 10–13, use Taylor series method of fourth order., 10. 0.900308., 13. 1 + h +, , h2, , +, , (h3/3), , +, , (h4/12), , 11. 0.110342., , 12. 1.110342, 1.242806., , 14. 1.1105., , 15. 0.66475., , Exercise 4.2, 1. h = 0.2. 1.214076, 1.648922. 2. 1.196, 3. h = 0.1: 1.116492, 1.273563. 4. y(0.2) ≈ 1.866204, y(0.4) ≈ 3.07267, 5. y(0.1) ≈ 1.111463, y(0.2) ≈ 1.253015., 6. y(0.2) ≈ 1.2428, y(0.4) ≈ 1.583636., 7. y(0.2) ≈ 1.821846, y(0.4) ≈ 3.325775., 8. y(0.1) ≈ 1.099383, y(0.2) ≈ 1.195440., Exercise 4.3, 1. Set u = y. u′ = v, v′ = e2t – 2u – 3v, u(0) = 1, v(0) = 1., 2. Set u = y. u′ = v, v′ = sin 2t – 5u + 6v, u(0) = 0, v(0) = 1., 3. Set u = y. u′ = v, v′ = tet – u – 2v, u(0) = 0.5, v(0) = 0.8., In Problems 4–7, use Taylor series method of fourth order., 4. Set u = y. u′ = v, v′ = e2t sin t – 2u + 2v, u(0) = – 0.4, v(0) = – 0.6, y(0.1) ≈ – 0.461735., 5. Set u = y. u′ = v, v′ = et – 2u – 3v, u(0) = 1, v(0) = 1, y(0.2) ≈ 1.133067., 6. Set u = y. u′ = v, v′ = e2t – 4u + 4v, u(0) = 0.5, v(0) = 1, y(0.2) ≈ 0.775727., 7. Set u = y. u′ = v, v′ = et – 5u + 6v, u(0) = 0, v(0) = – 1, y(0.1) ≈ – 0.129492., 8. Set u = y. u′ = v, v′ = e2t sin t – 2u + 2v, u(0) = – 0.4, v(0) = – 0.6, y(0.2) ≈ – 0.525572., 9. Set u = y. u′ = v, v′ = – u – v, u(0) = 1, v(0) = 0, y(0.1) ≈ 0.995167., 10. Set u = y. u′ = v, v′ = et – 2u – 3v, u(0) = 1, v(0) = 1, y(0.2) ≈ 1.133187., 11. Set u = y. u′ = v, v′ = tet – u – 2v, u(0) = 0.5, v(0) = 0.8, y(0.2) ≈ 0.623546., 12. Set u = y. u′ = v, v′ = – u – xv, u(0) = 1, v(0) = 0, k1 = 0.0, l1 = – h., Exercise 4.4, In the following problems, two iterations of the corrector in Milne’s method were performed., Taylor series method of fourth order was used. Two iterations of the corrector in AdamsBashforth predictor-corrector method were performed., 1. y(0.1) = 1.116887, y(0.2) = 1.277391, y(0.3) = 1.504187. y(0.4) = 1.839364., 2. y(4.4) = 1.018737., 4. y(0.8) = 0.304614, y(1.0) = 0.455551., , 3. y(0.8) = 2.013683.
Page 251 :
240, , NUMERICAL METHODS, , 5. y(0.1) = 1.116838, y(0.2) = 1.277276, y(0.3) = 1.503843, y(0.4) = 1.839043., 6. y(0.1) = 0.900325, y(0.2) = 0.802520, y(0.3) = 0.708222, y(0.4) = 0.618784., 7. y(0.1) = 0.953688, y(0.2) = 0.914512, y(0.3) = 0.882124, y(0.4) = 0.856192., 8. y(1.1) = – 0.2, y(1.2) = – 0.4652, y(1.3) = – 0.822709, y(1.4) = – 1.483650., 9. y(0.1) = 1.104829, y(0.2) = 1.218596, y(0.3) = 1.34039, y(0.4) = 1.468174., 10. y(0.2) = 0.8293, y(0.4) = 1.214091, y(0.6) = 1.648947, y(0.8) = 2.127230., 11. y(1.4) = 2.575142., 12. y(0.1) = 0.1, y(0.2) = 0.19, y(0.3) = 0.271, y(0.4) = 0.3439. y(0.5) = 0.406293.
Page 252 :
#, Boundary Value Problems in Ordinary, Differential Equations and Initial and, Boundary Value Problems in Partial, Differential Equations, 5.1 INTRODUCTION, Boundary value problems are of great importance in science and engineering. In this chapter,, we shall discuss the numerical solution of the following problems:, (a) Boundary value problems in ordinary differential equations., (b) Boundary value problems governed by linear second order partial differential equations. We shall discuss the solution of the Laplace equation uxx + uyy = 0 and the, Poisson equation uxx + uyy = G(x, y)., (c) Initial boundary value problems governed by linear second order partial differential, equations. We shall discuss the solution of the heat equation ut = c2uxx and the wave, equation utt = c2uxx under the given initial and boundary conditions., , 5.2, , BOUNDARY VALUE PROBLEMS GOVERNED BY SECOND ORDER ORDINARY, DIFFERENTIAL EQUATIONS, , A general second order ordinary differential equation is given by, y″ = f(x, y, y′),, , x ∈ [a, b]., , (5.1), , Since the ordinary differential equation is of second order, we need to prescribe two, suitable conditions to obtain a unique solution of the problem. If the conditions are prescribed, at the end points x = a and x = b, then it is called a two-point boundary value problem. For our, discussion in this chapter, we shall consider only the linear second order ordinary differential, equation, a0(x) y″ + a1(x) y′ + a2(x) y = d(x),, or, in the form, 241, , x ∈ [a, b], , (5.2)
Page 253 :
242, , NUMERICAL METHODS, , y″ + p(x) y′ + q(x) y = r(x),, , x ∈ [a, b] ., , (5.3), , We shall assume that the solution of Eq.(5.3) exists and is unique. This implies that, a0(x), a1(x), a2(x) and d(x), or p(x), q(x) and r(x) are continuous for all x ∈ [a, b]., The two conditions required to solve Eq.(5.2) or Eq.(5.3), can be prescribed in the following three ways:, (i) Boundary conditions of first kind The dependent variable y(x) is prescribed at the, end points x = a and x = b., y(a) = A, y(b) = B., , (5.4), , (ii) Boundary conditions of second kind The normal derivative of y(x), (slope of the, solution curve) is prescribed at the end points x = a and x = b., y′(a) = A, y′(b) = B., , (5.5), , (iii) Boundary conditions of third kind or mixed boundary conditions, a0 y(a) – a1 y′(a) = A,, b0y(b) + b1 y′(b) = B,, , (5.6), , where a0, a1, b0, b1, A and B are constants such that, a0a1 ≥ 0, | a0 | + | a1 | ≠ 0, b0b1 ≥ 0, | b0 | + | b1 | ≠ 0, | a0 | + | b0 | ≠ 0., We shall consider the solution of Eq.(5.2) or Eq.(5.3) under the boundary conditions of, first kind only, that is, we shall consider the solution of the boundary value problem, y″ + p(x) y′ + q(x) y = r(x),, , x ∈ [a, b], , y(a) = A, y(b) = B., , (5.7), , Finite difference method Subdivide the interval [a, b] into n equal sub-intervals. The length, of the sub-interval is called the step length. We denote the step length by ∆x or h. Therefore,, , b−a, , or b = a + nh., n, The points a = x0, x1 = x0 + h, x2 = x0 + 2h, ....., xi = x0 + ih, ....., xn = x0 + nh = b, are called, the nodes or nodal points or lattice points (Fig. 5.1)., ∆x = h =, , h, a = x0, , h, x1, , h, x2, , xi–1, , xi, , xi+1, , xn = b, , Fig. 5.1 Nodes., , We denote the numerical solution at any point xi by yi and the exact solution by y(xi)., In Chapter 3, we have derived the following approximations to the derivatives., Approximation to y′(xi) at the point x = xi, (i) Forward difference approximation of first order or O(h) approximation:, y′(xi ) ≈, , 1, 1, [y(xi+1) – y(xi)], or y′i =, [y – yi]., h, h i+1, , (5.8)
Page 254 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 243, , (ii) Backward difference approximation of first order or O(h) approximation:, y′(xi) ≈, , 1, [y(xi) – y(xi–1)],, h, , or y′i =, , 1, [y – yi–1]., h i, , (5.9), , (iii) Central difference approximation of second order or O(h2) approximation:, y′(xi) ≈, , 1, 1, [y(xi+1) – y(xi–1)], or y′i =, [y – yi–1]., 2h, 2h i+1, , (5.10), , Approximation to y″(xi) at the point x = xi, Central difference approximation of second order or O(h2) approximation:, y″(xi) ≈, or, , y″i =, , 1, h2, 1, h2, , [y(xi+1) – 2y(xi) + y(xi–1)],, [yi+1 – 2yi + yi–1]., , (5.11), , Applying the differential equation (5.3) at the nodal point x = xi, we obtain, y″(xi) + p(xi ) y′(xi ) + q(xi ) y(xi ) = r(xi )., , (5.12), , Since y(a) = y(x0) = A and y(b) = y(xn) = B are prescribed, we need to determine the, numerical solutions at the n – 1 nodal points x1, x2, ..., xi, ...., xn–1., Now, y′(xi) is approximated by one of the approximations given in Eqs. (5.8), (5.9), (5.10), and y″(xi) is approximated by the approximation given in Eq.(5.11). Since the approximations, (5.10) and (5.11) are both of second order, the approximation to the differential equation is of, second order. However, if y′(xi) is approximated by (5.8) or (5.9), which are of first order, then, the approximation to the differential equation is only of first order. But, in many practical, problems, particularly in Fluid Mechanics, approximations (5.8), (5.9) give better results (nonoscillatory solutions) than the central difference approximation (5.10)., Using the approximations (5.10) and (5.11) in Eq.(5.12), we obtain, 1, h, , or, , 2, , [yi+1 – 2yi + yi–1] +, , p( xi ), [yi+1 – yi–1] + q(xi) yi = ri, 2h, , 2[yi+1 – 2yi + yi–1] + h p(xi) [yi+1 – yi–1] + 2h2 q(xi) yi = 2h2 ri ., , Collecting the coefficients, we can write the equation as, ai yi–1 + bi yi + ci yi+1 = di , i = 1, 2, …, n – 1, where, , (5.13), , ai = 2 – h p(xi), bi = – 4 + 2h2 q(xi), ci = 2 + h p(xi), di = 2h2r(xi)., , Let us now apply the method at the nodal points. We have the following equations., At x = x1, or, , i = 1:, , a1 y0 + b1 y1 + c1 y2 = d1, or b1 y1 + c1 y2 = d1 – a1 A = d1*., , (5.14), , At x = xi , i = 2, 3, …, n – 2 :, ai yi–1 + bi yi + ci yi +1 = di, , (5.15)
Page 255 :
244, , NUMERICAL METHODS, , At x = xn–1, or i = n – 1:, * ., an–1 yn–2 + bn–1 yn–1 + cn–1 yn = dn–1, or an–1 yn–2 + bn–1 yn–1 = dn–1 – cn–1 B = dn−1, , (5.16), , Eqs.(5.14), (5.15), (5.16) give rise to a system of (n – 1) × (n – 1) equations Ay = d for the, unknowns y1, y2, ..., yi, ..., yn–1, where A is the coefficient matrix and, *, y = [y1, y2, ..., yi, ..., yn–1]T, d = [ d1* , d2, ..., di, ..., dn–2, dn−1, ] T., , It is interesting to study the structure of the coefficient matrix A. Consider the case, when the interval [a, b] is subdivided into n = 10 parts. Then, we have 9 unknowns, y1, y2, ....,, y9, and the coefficient matrix A is as given below., Remark 1 Do you recognize the structure of A? It is a tri-diagonal system of algebraic equations., Therefore, the numerical solution of Eq.(5.2) or Eq.(5.3) by finite differences gives rise to a, tri-diagonal system of algebraic equations, whose solution can be obtained by using the Gauss, elimination method or the Thomas algorithm. Tri-diagonal system of algebraic equations is, the easiest to solve. In fact, even if the system is very large, its solution can be obtained in a, few minutes on a modern desk top PC., , LMb, MM0a, M0, A = M0, MM0, MM00, MN0, , c1, b2, a3, 0, 0, 0, 0, 0, 0, , 1, 2, , 0, c2, b3, a4, 0, 0, 0, 0, 0, , 0, 0, c3, b4, a5, 0, 0, 0, 0, , 0, 0, 0, c4, b5, a6, 0, 0, 0, , 0, 0, 0, 0, c5, b6, a7, 0, 0, , 0, 0, 0, 0, 0, c6, b7, a8, 0, , 0, 0, 0, 0, 0, 0, c7, b8, b9, , 0, 0, 0, 0, 0, 0, 0, c8, c9, , OP, PP, PP, PP, PP, PQ, , Remark 2 Does the system of equations (5.13) always converge? We have the following sufficient, condition: If the system of equations (5.13) is diagonally dominant, then it always converges., Using the expressions for ai, bi, ci, we can try to find the bound for h for which this condition is, satisfied., Example 5.1 Derive the difference equations for the solution of the boundary value problem, y″ + p(x) y′ + q(x) y = r(x),, , x ∈ [a, b], , y(a) = A, y(b) = B, using central difference approximation for y″ and forward difference approximation for y′., Solution Using the approximations, yi′′ =, , 1, h, , 2, , [ yi + 1 − 2 yi + yi − 1 ],, , yi′ =, , 1, [ yi + 1 − yi ], h, , in the differential equation, we obtain, , 1, h, , 2, , [ yi+ 1 − 2 yi + yi− 1 ] +, , p( xi ), [ yi+ 1 − yi ] + q( xi ) yi = r ( xi ), h
Page 257 :
246, , NUMERICAL METHODS, , We have the following system of equations, , LM− 39, MN 240, , OP LM y OP LM− 20OP, PQ MN yy PQ = MN− 560PQ ., , 20, 0, 24, − 47, 28 − 55, , 1, , 2, 3, , We can solve this system using Gauss elimination. We obtain, , LM− 39 20 0 − 20OP R LM 1 − 20/39 0 20 / 39OP , R – 24R ,, 24, 0, 24, 0 ,, , 24, − 47, MN 240 − 47, 28, 28 − 55 − 56PQ − 39 MN 0, − 55 − 56 PQ, 0, 20 / 39 O, LM1 − 20/39 0 20 / 39 OP R, L1 − 20/39, 1, 0 − 1353/39 24 − 480/39 ,, , M0, − 936/1353 480/1353P ,, MN0 28 − 55 − 56 PQ (− 1353/39) MN0 28, − 55, − 56 PQ, 0, 20 / 39 O, L1 − 20/39, R – 28R , M0, − 936/1353, 1, 480/1353 P, MN0 0 − 48207/1353 − 89208/1353PQ, 1, , 2, , 1, , 2, , 3, , 2, , From the last equation, we get y3 =, Back substitution gives y2 =, , 89208, = 1.85052., 48207, , 480, 936, +, (1.85052) = 1.63495,, 1353 1353, y1 =, , 20, (1 + 1.63495) = 1.35126., 39, , Example 5.4 Using the second order finite difference method, find y(0.25), y(0.5), y(0.75) satisfying the differential equation y″ – y = x and subject to the conditions y(0) = 0, y(1) = 2., Solution We have h = 0.25 and n =, We have five nodal points, , b − a 1− 0, =, = 4., h, 0.25, , x0 = 0.0, x1 = 0.25, x2 = 0.5, x3 = 0.75, x4 = 1.0., , We are given the data values y(x0) = y0 = y(0) = 0, y(x4) = y4 = y(1) = 2., We are to determine the approximations for y(0.25), y(0.5), y(0.75). Using the central, difference approximation for y″i, we get, 1, h2, , [ yi +1 − 2 yi + yi − 1 ] − yi = xi , or 16yi–1 – 33yi + 16yi+1 = xi., , We have the following difference equations., For i = 1, x1 = 0.25, y0 = 0.0 :, , 16y0 – 33y1 + 16y2 = 0.25 or – 33y1 + 16y2 = 0.25,, , For i = 2, x2 = 0.5 :, , 16y1 – 33 y2 + 16y3 = 0.5,, , For i = 3, x3 = 0.75, y4 = 2.0 :, , 16y2 – 33y3 + 16y4 = 0.75, , or 16y2 – 33y3 = – 31.25.
Page 258 :
247, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , We have the following system of equations, , LM− 33, MN 160, , 16, 0, 16, − 33, 16 − 33, , OP LM y OP LM 0.25OP ., PQ MN yy PQ = MN− 31.025.5PQ, 1, , 2, 3, , We can solve this system using Gauss elimination. We obtain, , LM− 33 16 0 0.25OP R LM 1 − 0.48485 0 − 0.007576OP, , R, 16, 0.5, 16, 0.5 ,, , 16, − 33, MN 160 − 33, 16, 16 − 33 − 31.25PQ − 33 MN 0, − 33, − 56 PQ, LM1 − 0.48485 0 − 0.007576OP R, L1 − 0.48485 0, 0 − 25.2424 16, 0.621216 ,, , M0, MN0 16 − 33 − 31.25 PQ (− 25.2424) MN0 161 − 0−.63385, 33, L1 − 0.48485 0 − 0.007576OP ., R – 16R , M0, − 0.02461, MN0 01 −− 022.63385, .8584 − 30.85624 PQ, 1, , 2, , 2, , 3, , – 16R1,, , OP, PQ, , − 0.007576, − 0.02461 ,, − 31.25, , 2, , From the last equation, we get, , y3 =, , 30.85624, = 1.34989., 22.8584, , Back substitution gives, y2 = – 0.02461 + 0.63385(1.34989) = 0.83102,, y1 = – 0.007576 + 0.48485(0.83102) = 0.39534., Example 5.5 Solve the boundary value problem y″ + 5y′ + 4y = 1, y(0) = 0, y(1) = 0 by finite, difference method. Use central difference approximations with h = 0.25. If the exact solution is, y(x) = Ae–x + Be–4x + 0.25, where A =, , e −3 − e, 4(1 − e −3 ), , , B = – 0.25 – A, , find the magnitude of the error and percentage relative error at x = 0.5., Solution We have h = 0.25 and n =, We have five nodal points, , b − a 1− 0, =, = 4., h, 0.25, , x0 = 0.0, x1 = 0.25, x2 = 0.5, x3 = 0.75, x4 = 1.0., , We are given the data values y(x0) = y0 = y(0) = 0, y(x4) = y4 = y(1) = 0., We are to determine the approximations for y(0.25), y(0.5), y(0.75). Using the central, difference approximations, we get, 1, h, , or, , 2, , [ yi + 1 − 2 yi + yi −1 ] +, , 5, ( yi + 1 − yi − 1 ) + 4yi = 1,, 2h, , 16[ yi+1 – 2yi + yi–1] + 10(yi+1 – yi–1) + 4yi = 1, or 6yi–1 – 28yi + 26yi+1 = 1.
Page 259 :
248, , NUMERICAL METHODS, , We have the following difference equations., For i = 1, x1 = 0.25, y0 = 0.0 :, , 6y0 – 28y1 + 26y2 = 1 or – 28y1 + 26y2 = 1., , For i = 2, x2 = 0.5 :, , 6y1 – 28y2 + 26y3 = 1., , For i = 3, x3 = 0.75, y4 = 0 :, , 6y2 – 28y3 + 26y4 = 1, , or 6y2 – 28y3 = 1., , We have the following system of equations, , LM− 28, MN 60, , OP LM y OP LM1OP ., PQ MN yy PQ = MN11PQ, , 26, 0, − 28, 26, 6 − 28, , 1, , 2, 3, , We can solve this system using Gauss elimination. We obtain, , LM− 28 26 0 1OP R LM1 − 0.92857 0, 26, 26 1 ,, , 6, − 28, MN 60 − 286 − 28, 6, 1PQ − 28 MN0, − 28, LM1 − 0.92857 0 − 0.03571OP R, L1, 0 − 22.42858 26, 1.21426 ,, , M0, MN0, PQ (− 22.42858) MN0, − 28, 6, 1, − 0.03571O, 0, L1 − 0.92857, R – 6R , M0, − 1.15924 − 0.05414P ., 1, MN0 0 − 2104456, ., 1.32484 PQ, , OP, PQ, , − 0.03571, 1, , R2 – 6R1, 1, , 1, , 2, , 3, , 2, , From the last equation, we get y3 =, , 1.32484, = – 0.06295., − 21.04456, , Back substitution gives, y2 = – 0.05414 – 1.15924(0.06295) = – 0.12711,, y1 = – 0.03571 – 0.92857(0.12711) = – 0.15374., We also have A = – 0.70208, B = 0.45208, y(0.5) = Ae–0.5 + Be–2 = 0.11465., Now,, , | error at x = 0.5 | = | y2 – y(0.5) | = | – 0.12711 + 0.11465 | = 0.01246., Percentage relative error =, , OP, PQ, , − 0.92857, − 0.03571, 0, − 1.15924 − 0.05414, 1, − 28, 6, 1, , 0.01246, (100) = 10.8%., 0.11465, , Example 5.6 Solve the boundary value problem, (1 + x2)y″ + 4xy′ + 2y = 2, y(0) = 0, y(1) = 1/2, by finite difference method. Use central difference approximations with h = 1/3., Solution We have h = 1/3. The nodal points are x0 = 0, x1 = 1/3, x2 = 2/3, x3 = 1.
Page 260 :
249, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , Using the central difference approximations, we obtain, , 1, h, , 2, , (1 + xi2 )[ yi+ 1 − 2 yi + yi−1 ] +, , 4 xi, ( yi+ 1 − yi− 1 ) + 2 yi = 2, 2h, , [9(1 + xi2 ) − 6 xi ] yi − 1 + [2 − 18(1 + xi2 )] yi + [9(1 + xi2 ) + 6 xi ] yi + 1 = 2., , or, , We have the following difference equations., For i = 1,, , x1 = 1/3, y0 = 0 :, , LM9FG 1 + 1IJ − 2OP y + LM2 − 18 FG 1 + 1IJ OP y + LM9FG 1 + 1IJ + 2OP y, N H 9K Q N H 9 K Q N H 9 K Q, 0, , or, , 1, , 2, , =2, , – 18y1 + 12y2 = 2., , For i = 2, x1 = 2/3, y3 = 1/2 :, , LM9FG1 + 4 IJ − 4OP y + LM2 − 18 FG1 + 4 IJ OP y + LM9FG1 + 4 IJ + 4OP y, N H 9 K Q N H 9K Q N H 9 K Q, 1, , 2, , 3, , =2, , or 9y1 – 24y2 = – 6.5., Solving the equations, – 9y1 + 6y2 = 1, 9y1 – 24y2 = – 6.5, we obtain, , y1 =, , 15, 49.5, = 0.092592, y2 =, = 0.305556 ., 162, 162, , REVIEW QUESTIONS, 1. Write the first order difference approximations for y′(xi) based on (i) forward differences, (ii) backward differences., Solution, (i) y′(xi) = [ yi+1 – yi]/(h),, , (ii) y′(xi) = [yi – yi–1]/h, where h is the step length., , 2. Write the second order difference approximations for (i) y′(xi), (ii) y″(xi) based on central, differences., Solution (i) y′(xi) = [yi+1 – yi–1]/(2h), (ii) y″(xi) = [yi+1 – 2yi + yi–1]/h2,, where h is the step length., 3. Finite difference methods when applied to linear second order boundary value problems in ordinary differential equations produce a system of linear equations Ay = b., What is the structure of the coefficient matrix A ?, Solution Tridiagonal matrix., 4. What types of methods are available for the solution of linear system of algebraic, equations ?, Solution (i) Direct methods. (ii) Iterative methods.
Page 261 :
250, , NUMERICAL METHODS, , 5. When iterative methods are used to solve the linear system of algebraic equations,, under what conditions convergence to the exact solution is guaranteed?, Solution A sufficient condition for convergence is that the coefficient matrix A should, n, , be diagonally dominant, that is, |a ii |≥, , ∑, , |a ij |. That is, in this case convergence is, , j = 1, i ≠ j, , guaranteed. Since it is a sufficient condition, it implies that the system may converge, even if the system is not diagonally dominant., , EXERCISE 5.1, Solve the following boundary value problems using the finite difference method and central, difference approximations., 1. y″ = xy, y(0) = 0, y(1) = 1 with h = 0.25., 2. y″ = y + 1, y(0) = 0, y(1) = e – 1 with h = 1/3. If the exact solution is y(x) = ex – 1, find the, absolute errors at the nodal points., 3. y″ = (y + 1)/4, y(0) = 0, y(1) =, , e – 1 with h = 1/4., , 4. y″ = y′ + 1, y(0) = 1, y(1) = 2(e – 1) with h = 1/3. If the exact solution is y(x) = 2ex – x – 1,, find the absolute errors at the nodal points., 5. y″ – y = – 4xex, y(0) = 0, y(1) = 1 with h = 0.25., 6. y″ = 2x–2y + x–1, y(2) = 0, y(3) = 0 with h = 1/3., 7. y″ + 3y′ + 2y = 1, y(0) = 1, y(1) = 0 with h = 1/3., 8. y″ – 3y′ + 2y = 0, y(1) = 2, y(2) = 0 with h = 1/4., 9. x2y″ = 2y – x, y(2) = 0, y(3) = 0 with h = 1/3., 10. Solve the boundary value problem y″ – 10y′ = 0, y(0) = 0, y(1) = 1 with h = 0.25, by using, central difference approximation to y″ and (i) central difference approximation to y′, (ii), backward difference approximation to y′, (iii) forward difference approximation to y′. If, the exact solution is y(x) = (e10x – 1)/(e10 – 1), compare the magnitudes of errors at the, nodal points in the three methods., , 5.3, , CLASSIFICATION OF LINEAR SECOND ORDER PARTIAL DIFFERENTIAL, EQUATIONS, , In this and later sections, we shall study the numerical solution of some second order linear, partial differential equations. Most of the mathematical models of the physical systems give, rise to a system of linear or nonlinear partial differential equations. Since analytical methods, are not always available for solving these equations, we attempt to solve by numerical methods. The numerical methods can broadly be classified as finite element methods and finite, difference methods. We shall be considering only the finite difference methods for solving, some of these equations.
Page 262 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 251, , First, we classify the linear second order partial differential equation, Auxx + 2Buxy + Cuyy + Dux + Euy + Fu + G = 0, , (5.17), , where A, B, C, D, E, F and G are functions of x, y or are real constants., The partial differential equation is called a, if B2 – AC < 0, , Elliptic equation, Parabolic equation, Hyperbolic equation, , (5.18 i), , if, , B2, , – AC = 0, , (5.18 ii), , if, , B2, , – AC > 0 ., , (5.18 iii), , Remark 3 Some books write the coefficient of u xy in Eq.(5.17) as B. Then, the condition in, Eq.(5.18) changes to B2 – 4AC. Note that the lower order terms do not contribute to the classification of the partial differential equation., The simplest examples of the above equations are the following:, Parabolic equation:, , ut = c2uxx ,, c2uxx, , Hyperbolic equation:, , utt =, , ,, , Elliptic equation:, , uxx + uyy = 0,, , (One dimensional heat equation)., , (5.19), , (One dimensional wave equation)., , (5.20), , (Two dimensional Laplace equation)., , (5.21), , We can verify that, in Eq.(5.19),, , A = c2, B = 0, C = 0, , and B2 – AC = 0., , in Eq.(5.20),, , A = c2, B = 0, C = – 1, , and B2 – AC = c2 > 0., , in Eq.(5.21),, , A = 1, B = 0, C = 1, , and B2 – AC = – 1 < 0., , Remark 4 What is the importance of classification? Classification governs the number and, type of conditions that should be prescribed in order that the problem has a unique solution., For example, for the solution of the one dimensional heat equation (Eq.(5.19)), we require an, initial condition to be prescribed, u(x, 0) = f(x), and the conditions along the boundary lines x, = 0, and x = l, where l is the length of the rod (boundary conditions), are to be prescribed., Suppose that the one dimensional wave equation (Eq.(5.20)) represents the vibrations, of an elastic string of length l. Here, u(x, t) represents the displacement of the string in the, vertical plane. For the solution of this equation, we require two initial conditions to be prescribed, the initial displacement u(x, 0) = f(x), the initial velocity ut(x, 0) = g(x), and the, conditions along the boundary lines x = 0 and x = l, (boundary conditions), are to be prescribed., For the solution of the Laplace’s equation (Eq.(5.21)), we require the boundary conditions to be prescribed on the bounding curve., Remark 5 Elliptic equation together with the boundary conditions is called an elliptic boundary, value problem. The boundary value problem holds in a closed domain or in an open domain, which can be conformally mapped on to a closed domain. For example, Laplace’s equation, (Eq.(5.21)) may be solved inside, say, a rectangle, a square or a circle etc. Both the hyperbolic, and parabolic equations together with their initial and boundary conditions are called initial, value problems. Sometimes, they are also called initial-boundary value problems. The initial, value problem holds in either an open or a semi-open domain. For example, in the case of the, one dimensional heat equation (Eq.(5.19)), x varies from 0 to l and t > 0. In the case of the one, dimensional wave equation (Eq.(5.20)), x varies from 0 to l and t > 0.
Page 263 :
252, , NUMERICAL METHODS, , Example 5.7 Classify the following partial differential equations., (a) uxx = 6ux + 3uy., , (b) 2uxx + 3uyy – ux + 2uy = 0., , (c) utt + 4utx + 4uxx + 2ux + ut = 0., , (d) uxx + 2xuxy + (1 – y2)uyy = 0., , Solution, (a) Write the given equation as uxx – 6ux – 3uy = 0. We have A = 1, B = 0, C = 0 and, B2 – AC = 0. Hence, the given partial differential equation is a parabolic equation., (b) We have A = 2, B = 0, C = 3 and B2 – AC = – 6 < 0.Hence, the given partial differential, equation is an elliptic equation., (c) We have A = 1, B = 2, C = 4 and B2 – AC = 0. Hence, the given partial differential, equation is a parabolic equation., (d) We have A = 1, B = x, C = 1 – y2 and B2 – AC = x2 – (1 – y2) = x2 + y2 – 1. Hence, if, x2 + y2 – 1 > 0, that is, outside the unit circle, 2, 2, x +y =1, Parabolic, x2 + y2 = 1, the given partial differential equation is an hyperbolic equation. If x2 + y2 – 1, Elliptic, Hyperbolic, = 0, that is, on the unit circle x2 + y2 = 1, the, given partial differential equation is a parabolic equation. If x2 + y2 – 1 < 0,that is, inside, the unit circle x2 + y2 = 1, the given partial, Fig. 5.2. Example 5.7., differential equation is an elliptic equation, (see Fig. 5.2)., , EXERCISE 5.2, Classify the following partial differential equations., 1. uxx + 4uyy = ux + 2uy = 0., 3. uxx +, 5. uxx +, , 5.4, , 4xuxy + (1 – 4y2)uyy = 0., 4uxy + (x2 + 4y2)uyy = x2 +, , 2. uxx – uyy + 3ux + 4uy = 0., 4. utt + (5 + 2x2)uxt + (1 + x2)(4 + x2)uxx = 0., y2 ., , FINITE DIFFERENCE METHODS FOR LAPLACE AND POISSON EQUATIONS, , In this section, we consider the solution of the following boundary value problems governed by, the given partial differential equations along with suitable boundary conditions., (a) Laplace’s equation: uxx + uyy = ∇2u = 0, with u(x, y) prescribed on the boundary, that, is, u(x, y) = f(x, y) on the boundary., (b) Poisson’s equation: uxx + uyy = ∇2u = G(x, y), with u(x, y) prescribed on the boundary,, that is, u(x, y) = g(x, y) on the boundary., In both the problems, the boundary conditions are called Dirichlet boundary conditions, and the boundary value problem is called a Dirichlet boundary value problem., Finite difference method We have a two dimensional domain (x, y) ∈ R. We superimpose on, this domain R, a rectangular network or mesh of lines with step lengths h and k respectively,
Page 264 :
253, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , parallel to the x- and y-axis. The mesh of lines is called a grid. The points of intersection of the, mesh lines are called nodes or grid points or mesh points. The grid points are given by (xi, yj),, (see Figs. 5.3 a, b), where the mesh lines are defined by, xi = ih, i = 0, 1, 2, ...; yj = jk, j = 0, 1, 2, ..., If h = k, then we have a uniform mesh. Denote the numerical solution at (xi, yj) by ui, j ., y, , y, , O, , x, , O, , x, , Fig. 5.3a. Nodes in a rectangle., , Fig. 5.3b. Nodes in a square., , At the nodes, the partial derivatives in the differential equation are replaced by suitable difference approximations. That is, the partial differential equation is approximated by a, difference equation at each nodal point. This procedure is called discretization of the partial, differential equation. We use the following central difference approximations., (ux)i, j =, (uxx)i, j =, , 1, (u, – ui–1, j),, 2h i+1, j, 1, h, , 2, , (uy)i, j =, , (ui+1, j – 2ui, j + ui–1, j),, , 1, (u ,, – ui, j–1),, 2k i j+1, , (uyy)i, j =, , 1, k2, , (ui, j+1 – 2ui, j + ui,, , j–1)., , Solution of Laplace’s equation We apply the Laplace’s equation at the nodal point (i, j)., Inserting the above approximations in the Laplace’s equation, we obtain, (uxx)i, j + (uyy)i, j =, or, , 1, 1, (ui+1, j – 2ui, j + ui–1, j) + 2 (ui ,, h2, k, , j+1, , – 2ui, j + ui,, , (ui+1, j – 2ui, j + ui–1, j) + p2 (ui, j+1 – 2ui, j + ui, j–1) = 0, where p = h/k., , j–1), , =0, , (5.22), (5.23), , If h = k, that is, p = 1 (called uniform mesh spacing), we obtain the difference approximation as, ui+1, j + ui–1, j + ui, j+1 + ui, j–1 – 4ui, j = 0, , (5.24), , This approximation is called the standard five point formula. We can write this formula as, ui, j =, , 1, (u, + ui–1, j + ui, j+1 + ui, j–1)., 4 i+1, j, , (5.25), , We observe that ui, j is obtained as the mean of the values at the four neighbouring, points in the x and y directions., The nodal points that are used in computations are given in Fig.5.4., Remark 6 The nodes in the mesh are numbered in an orderly way. We number them from left, to right and from top to bottom or from bottom to top. A typical numbering is given in Figs.5.5a,, 5.5b.
Page 266 :
255, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , We have the following linear algebraic system of equations,, , LM− 4, MM 01, MM 01, MM 0, MM 00, MN 0, , OP LMu OP LMb OP, PP MMuu PP MMbb PP, PP MMuu PP = MMb0 PP, PP MMu PP MMb PP, PP MMuu PP MMbb PP, PQ MNu PQ MNb PQ, , 1, 0, 1, 0, 0, 0, 0, 0, 1, 0, 1, 0, 0, 0, 0, −4, 1 −4, 0, 0, 1, 0, 0, 0, 0, 0 −4, 1, 0, 1, 0, 0, 1, 0, 1 −4, 1, 0, 1, 0, 0, 1, 0, 1 −4, 0, 0, 1, 0, 0, 1, 0, 0 −4, 1, 0, 0, 0, 0, 1, 0, 1 −4, 1, 0, 0, 0, 0, 1, 0, 1 −4, , which is of the form Au = d., , 1, , 1, , 2, , 2, , 3, , 3, , 4, , 4, , 5, 6, , 6, , 7, , 7, , 8, , 8, , 9, , 9, , Remark 7 Do you recognize the structure of the matrix? It is a band matrix system. The half, band width is the number of nodal points on each mesh line, that is, 3. Therefore, the total, band width of the matrix is 3 + 3 + 1 = 7, that is, all the non-zero elements are located in this, band. In the general case, for a large n × n system (n unknowns on each mesh line), the half, band width is n and the total band width is n + n + 1 = 2n + 1. All the elements on the leading, diagonal are non-zero and are equals to – 4. Except in the case of the equations corresponding, to the nodal points near the boundaries, all the elements on the first super-diagonal and the, first sub-diagonal are non-zero and are equal to 1. The remaining two non-zero elements, (which equals 1) corresponding to each equation are located in the band. For equations corresponding to the nodal points near the boundary, the number of non-zero elements is less than, 5. At the corner points, the number of non-zero elements is 3 (in the above example, u1, u3, u7,, u9 are corner points) and at other points near the boundaries (in the above example, u2, u4, u6,, u8 are these points), the number of non-zero elements is 4. The remaining elements in the, matrix are all zero. This property is true in all problems of solving Dirichlet boundary value, problems for Laplace’s equation. The software for the solution of such band matrix systems is, available in all computers., Remark 8 Let us derive the error or truncation error (T.E) in the approximation for the, Laplace’s equation. Consider the case of uniform mesh, that is, h = k. Using the Taylor series, expansions in Eq.(5.23) with h = k, we obtain, [{u(xi+1, yj) – 2u(xi, yj) + u(xi–1, yj)} + {u(xi, yj+1) – 2u(xi, yj) + u(xi, yj–1)}], , LMR|F ∂u h ∂ u h ∂ u h ∂ u I, MNST|GH u + h ∂x + 2 ∂x + 6 ∂x + 24 ∂x + ...JK − 2u, F ∂u + h ∂ u − h ∂ u + h ∂ u − ...I |UV, + Gu − h, H ∂x 2 ∂x 6 ∂x 24 ∂x JK |W, R|F ∂u + h ∂ u + h ∂ u + h ∂ u + ...I − 2u, + SG u + h, T|H ∂y 2 ∂y 6 ∂y 24 ∂y JK, F ∂u + h ∂ u − h ∂ u + h ∂ u − ...I U|VOP, + Gu − h, H ∂y 2 ∂y 6 ∂y 24 ∂y JK |WPQ, 2, , =, , 2, , 3, , 3, , 2, , 2, , 4, , 3, , 2, , 3, , 4, , 3, , 2, , 2, , 4, , 2, , 2, , 3, , 4, , 3, , 4, , 4, , 3, , 3, , 2, , 4, , 3, , 2, , 2, , 4, , 3, , 4, , 4, , 3, , 4, , 4, , i, j
Page 267 :
256, , NUMERICAL METHODS, , LM F ∂ u + ∂ u I + h F ∂ u + ∂ u I + ...OP, MN GH ∂x ∂y JK 12 GH ∂x ∂y JK PQ, , = h2, , since,, , 2, , 2, , 2, , 4, , 2, , 4, , 4, , 4, , =, , 4, , i, j, , h4, 12, , F ∂ u + ∂ uI, GH ∂x ∂y JK, 4, , 4, , 4, , + ..., , 4, , i, j, , ∂2u ∂2u, +, = 0., ∂x 2 ∂y 2, , The truncation error of the method (5.23) when h = k, is given by, T.E = (ui+1, j – 2ui, j + ui–1, j) + (ui, j+1 – 2ui, j + ui, j–1), =, , F, GH, , h4 ∂ 4 u ∂ 4 u, +, 12 ∂x 4 ∂y 4, , I, JK, , + ..., i, j, , using the above derivation. Hence, the truncation error of the method is of order O(h4)., The order of the formula (5.23) is defined as, Order =, , 1, h2, , (T.E) = O(h2)., , We say that the method is of second order., What is the importance of the order of the finite difference formulas? When a method converges, it implies that the errors in the numerical solutions → 0 as h → 0. Suppose that a, method is of order O(h2). Then, if we reduce the step length h by a factor, say 2, and recompute the numerical solution using the step length h/2, then the error becomes O[(h/2)2] =, [O(h2)]]/4. Therefore, the errors in the numerical solutions are reduced by a factor of 4. This, can easily be checked at the common points between the two meshes., Another five point formula The standard five point formula (5.23) or (5.24) at (i, j) uses the, four neighbours, (i + 1, j), (i – 1, j), (i, j + 1), (i, j – 1), on the x and y axis. We can obtain another, five point formula by using the four neighbours on the diagonals, (i + 1, j + 1), (i – 1,, j + 1), (i + 1, j –1), (i – 1, j – 1). The five point formula for solving the Laplace’s equation is, given by, (uxx)i, j + (uyy)i, j =, , 1, 2h 2, , (ui+1, j+1 + ui–1, j+1 + ui+1, j–1 + ui–1, j–1 – 4ui, j ) = 0, , or, , ui+1, j+1 + ui–1, j+1 + ui+1, j–1 + ui–1, j–1 – 4ui, j = 0, , or, , ui, j =, , (5.26), (5.27), , 1, (u, + ui–1, j+1 + ui+1, j–1 + ui–1, j–1)., 4 i+1, j+1, , (5.28), , Note the factor 2 in the denominator of (5.26). This formula is called the diagonal five, point formula. The nodal points are given in Fig.5.6. Using the Taylor series expansions as in, Remark 8, we obtain the error or truncation error (T.E) in the formula as, T.E =, , h4, 6, , F∂ u + 6 ∂ u, GH ∂x ∂x ∂y, 4, , 4, , 4, , 2, , 2, , +, , ∂4u, ∂y 4, , I, JK, , + ..., i, j
Page 268 :
257, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , The order of the formula is given by, Order =, , 1, h2, , (T.E) = O(h2)., , Therefore, the orders of the standard and the diagonal five point formulas are the same., Solution of the system of equations The solution of the system of equations can be obtained by direct or iterative methods. For the purpose of our study, we shall consider the, solution of the system of equations Au = d by Gauss elimination (a direct method) and an, iterative method called Liebmann iteration, which is the application of Gauss-Seidel iterative, method to the present system. When the order of the system of equations is not large, say, about 50 equations, we use the direct methods. Dii + 1, j + 1, rect methods require the loading of all the elements, i – 1, j + 1, of the coefficient matrix and the right hand side, vector into the memory of the computer, which may, i, j, not be possible if the system is large. When the order of the system is large, which is the case in most, practical problems, we use the iterative methods., i + 1, j – 1, i – 1, j – 1, In fact, in many problems, we encounter thousands, of equations. Iterative methods do not require the, Fig. 5.6. Diagonal five point formula., loading of all the elements of the coefficient matrix, and the right hand side vector. Information of few, equations only can be loaded at a time., Solution of Poisson equation Consider the solution of the Poisson’s equation, uxx + uyy = ∇2u = G(x, y),, with u(x, y) prescribed on the boundary, that is, u(x, y) = g(x, y) on the boundary., Eqs. (5.23)-(5.25) become, (uxx)i, j + (uyy)i, j =, or, , 1, h, , 2, , (ui+1, j – 2ui, j + ui–1, j) +, , 1, k2, , (ui, j+1 – 2ui, j + ui, j–1) = Gi, j, , (ui+1, j – 2ui, j + ui–1, j) + p2 (ui, j+1 – 2ui, j + ui, j–1) = h2Gi, j ,, , (5.29), (5.30), , where Gi, j = G(xi, yj) and p = h/k., If h = k, that is, p = 1, we obtain the difference approximation as, ui+1, j + ui–1, j + ui, j+1 + ui, j–1 – 4ui, j = h2Gi, j ., , (5.31a), , This approximation is called the standard five point formula for Poisson’s equation., The formula (5.30) is of order O(h2 + k2) and formula (5.31a) is of order O(h2). We also call it a, second order formula., When h = k, the diagonal five point formula for solving the Poisson’s equation can be, written as, ui+1, j+1 + ui–1, j+1 + ui+1, j–1 + ui–1, j–1 – 4ui, j = 2h2Gi, j ., , (5.31b), , We shall illustrate the application of the finite difference method through the following, examples.
Page 269 :
258, , NUMERICAL METHODS, , Example 5.8 Solve uxx + uyy = 0 numerically for the following, mesh with uniform spacing and with boundary conditions as, shown below in the figure 5.7., , 3, , Solution We note that the partial differential equation and, the boundary conditions are symmetric about the diagonals, AC and BD. Hence, u1 = u4 and u2 = u3. Therefore, we need to, solve for two unknowns u1 and u2. We use the standard five, point formula, ui+1, j + ui–1, j, , 3, , D, , 6, , 6, , C, , u1, , u2, , u3, , u4, , 6, , 3, , A, , B, , 6, , + ui, j+1 + ui, j–1 – 4ui, j = 0., , We obtain the following difference equations., , 3, , Fig. 5.7. Example 5.8., , At 1: u2 + 3 + 3 + u3 – 4u1 = 0,, or, , – 4u1 + 2u2 = – 6,, , At 2: 6 + 6 + u1 + u4 – 4u2 = 0,, , or, , – 2u1 + u2 = – 3., , or, , 2u1 – 4u2 = – 12., , Adding the two equations, we get – 3u2 = – 15, or u2 = 5., From the first equation, we get, , 2u1 = u2 + 3 = 5 + 3 = 8, or u1 = 4., , Example 5.9 Solve uxx + uyy = 0 numerically for the following, mesh with uniform spacing and with boundary conditions, as shown below in the figure 5.8., , 4, , BD. Hence, u2 = u3 and we need to determine u1 , u 2 and u 4 ., We use the standard five point formula, , 4, , u1, , 2, , Solution We note that the partial differential equation and, the boundary conditions are symmetric about the diagonal, , ui+1, j + ui–1, j, , 2, , D, , C, , u2, , 6, , u4, , 8, , u3, , A, , + ui, j+1 + ui, j–1 – 4ui, j = 0., , B, , 6, , 8, , Fig. 5.8. Example 5.9., , We obtain the following difference equations., At1:, , u2 + 2 + 2 + u3 – 4u1 = 0,, , or, , – 4u1 + 2u2 = – 4,, , At 2, , 6 + 4 + u1 + u4 – 4u2 = 0,, , or, , u1 – 4u2 + u4 = – 10., , At 4: 8 + u2 + u3 + 8 – 4u4 = 0,, , or, , 2u2 – 4u4 = – 16,, , or, , – 2u1 + u2 = – 2., , or, , u2 – 2u4 = – 8., , We solve the system of equations using the Gauss elimination method. We use the, augmented matrix [A|d]., , LM− 2, MN 01, , 1, −4, 1, , 0, 1, −2, , LM, MN, , 1, R2, , 0, − (7/2) 0, , OP, PQ, , LM, MN, , −2, 1, R, − 10 ; 1 , 1, −8 −2 0, − 1/ 2, 1, 1, , 0, − 2/ 7, −2, , − 1/2, −4, 1, , OP, PQ, , 0, 1, −2, , 1, 22 / 7 ; R3, −8, , OP, PQ, L1, − R , M0, MN0, , LM, MN, , 1, 1, − 10 ; R2 − R1 , 0, −8, 0, , 2, , − 1/ 2, 1, 0, , − 1/2, − 7/2, 1, , 0, − 2/ 7, − 12 / 7, , 0, 1, −2, , OP, PQ, , 1, − 11 ;, −8, , OP, PQ, , 1, 22 / 7 ., − 78 / 7
Page 270 :
259, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , Solving the last equation, we get, , u4 =, , 78, = 6.5 ., 12, , Substituting in the second equation, we get, , u2=, , 22 13 35, +, =, = 5., 7, 7, 7, , Substituting in the first equation, we get, , u1 = 1 +, , 5, = 3.5 ., 2, , Example 5.10 Solve uxx + uyy = 0 numerically for the following, mesh with uniform spacing and with boundary conditions as, shown below in the figure 5.9., , 2, , Solution We note that the boundary conditions have no symmetry. Therefore, we need to find the values of the four un-, , 0, , knowns u1 , u 2 , u 3 and u 4 . We use the standard five point for-, , 0, , 3, , u1, , u2, , u3, , u4, , 1, , 2, , mula, ui+1, j + ui–1, j, , + ui, j+1 + ui, j–1 – 4ui, j = 0., , 0, , 0, , Fig. 5.9. Example 5.10., , We obtain the following difference equations., At1:, , u2 + 2 + 0 + u3 – 4u1 = 0,, , or, , – 4u1 + u2 + u3 = – 2., , At 2, , 1 + 3 + u1 + u4 – 4u2 = 0,, , or, , u1 – 4u2 + u4 = – 4., , At 3: u4 + u1 + 0 + 0 – 4u3 = 0,, , or, , u1 – 4u3 + u4 = 0., , At 4: 2 + u2 + u3 + 0 – 4u4 = 0,, , or, , u2 + u3 – 4u4 = – 2., , We solve the system of equations using the Gauss elimination method. We use the, augmented matrix [A|d]., , LM− 4, MM 11, N 0, , OP, PP, Q, , OP, PP, Q, , LM, MM, N, , 1 − 1/4 − 1/4, 0 1/2, 1, 1, 0 −2, 1, 0, 1 −4, −4, 0, 1 − 4 R1, −4, ;, ,, ; R2 − R1 , R3 − R1,, 1, 0, 1, 0, −4, 0 −4, 1, 0 −4, 0, 1, 1 −4 −2, 1, 1 −4 −2, , LM 1, MM00, N0, , 0, 1/2, − 1/4 − 1/4, 1/4, 1 − 9/2, − 15/4, ;, 1/4 − 15/4, 1 − 1/2, 1, 1 −4, −2, , OP, LM 1 − 1/4, R, PP F − 15 I ; MM00 1/14, Q GH 4 JK N0 1, 1/2 O, LM1, R, 0, 18/15 P, ,, − 4/5 P (− 56/15) M0, P, MN0, − 48/15Q, , LM 1, MM00, N0, , 0, − 1/4, − 1/4, 1, − 1/15 − 4/15, 0 − 56/15, 16/15, 0, 16/15 − 56/15, , 2, , 3, , OP, PP, Q, , 0, 1/2, − 1/4, 1, − 1/15 − 4/15 18/15 R3 − R2 ,, 4, 1, − 15/4, − 1/2, R4 − R2 ,, 1, −4, −2, , OP, PP, Q, , 0, 1/2, − 1/4 − 1/4, 1 − 1/15 − 4/15, 18/15, 0, 1, − 16/56 12/56 ;, 0 16/15 − 56/15 − 48/15
Page 272 :
261, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , We solve the system of equations using the Gauss elimination method. We use the, augmented matrix [A|d]., , LM− 4, MM 11, N 0, , OP, PP, Q, , OP, PP, Q, , LM, MM, N, , 1 − 0.25 − 0.25, 0 − 0.25, 1, 1, 0, 1, R1 1, 0, 1 − 5/3, −4, 0, 1 − 5/3, −4, ; R2 − R1 , R3 − R1 ,, ;, ,, 0, 1 − 1/3, −4, 0 −4, 1 − 1/3 − 4 1, 0, 1, 1 −4, −3, 1, 1 −4 −3, , OP, PP, Q, , LM 1, MM00, N0, , 0, − 0.25 − 0.25, − 0.25, R2, 0.25, 1 − 1.41667, − 3.75, ;, 0.25 − 3.75, 1 − 0.08333 − 3.75, 1, 1, −4, −3, , LM1, MM00, N0, , − 0.25, − 0.25, − 0.25, 0, 1 − 0.06667 − 0.26667 0.37778, − 3.75, − 0.08333 ;, 0.25, 1, −4, −3, 1, 1, , OP, PP, Q, , OP, PP, Q, , LM, MM, N, , 1 − 0.25, 0, − 0.25, − 0.25, R3, R3 − 0.25 R2 , 0, 1 − 0.06667 − 0.26667, 0.37778, ;, ,, R4 − R2 ,, 0, 0, 1.06667 − 0.17778, − 3.73333, − 3.73333, 0, 0, 1.06667 − 3.73333 − 3.377778, , OP, PP, Q, , LM 1, MM00, N0, , − 0.25, − 0.25, 0, − 0.25, 1 − 0.06667 − 0.26667 0.37778, ;, 0, 1, − 0.28572 − 0.04762, 0, 106667, ., − 3.73333 − 3.37778, , LM1, MM00, N0, , − 0.25, 1, 0, 0, , − 0.25, − 0.06667, 1, 0, , 0, − 0.26667, − 0.28572, − 3.42856, , R4 – 1.06667 R3,, , OP, PP, Q, , − 0.25, 0.37778, ., 0.04762, − 3.42857, , Last equation gives u4 = 1., Substituting in the third equation, we get u3 = 0.04762 + 0.28572 = 0.33334., Substituting in the second equation, we get, u2 = 0.37778 + 0.06667 (0.33334) + 0.26667 = 0.66667., Substituting in the first equation, we get u1 = – 0.25 + 0.25(0.66667 + 0.33334) = 0., Example 5.12 Solve the boundary value problem for the Poisson equation, uxx + uyy = x2 – 1, | x | ≤ 1, | y | ≤ 1,, u = 0 on the boundary of the square, using the five point formula with square mesh of width h = 1/2.
Page 273 :
262, , NUMERICAL METHODS, , Solution The mesh is given in Fig.5.11. The partial differential equation and the boundary, conditions are symmetric about x-and y-axis. We need to find the values of the four unknowns, u1, u2, u3 and u4. We use the standard five point formula, y, 0, , 0, , 0, , 0, , 0, , 0, , 0, , u4, , u3, , u4, , u2, , u1, , u2, , 0, , 0, 0, , x, , 0, u4, , u3, , u4, , 0, 0, , 0, , 0, , Fig. 5.11. Example 5.12., , ui+1, j + ui–1, j + ui, j+1 + ui, j–1 – 4ui, j = h2Gi, j = 0.25(xi2 – 1)., We obtain the following difference equations., u2 + u3 + u2 + u3 – 4u1 = – 0.25,, , At 1(0, 0):, or, , – 2u1 + u2 + u3 = – 0.125., , At 2(0.5, 0):, , 0 + u4 + u1 + u4 – 4u2 = 0.25(0.25 – 1) = – 0.1875,, , or, , u1 – 4u2 + 2u4 = – 0.1875., , At 3(0, 0.5):, , u4 + 0 + u4 + u1 – 4u3 = 0.25(0 – 1) = – 0.25,, , or, , u1 – 4u3 + 2u4 = – 0.25., , At 4(0.5, 0.5):, , 0 + 0 + u3 + u2 – 4u4 = 0.25(0.25 – 1) = – 0.1875,, , or, , u2 + u3 – 4u4 = – 0.1875., , We solve the system of equations using the Gauss elimination method. We use the, augmented matrix [A|d]., , LM− 2, MM 11, N0, LM1, MM00, N0, , OP, PP, Q, , 1, 1, 0 − 0.125, R, 0, 2 − 0.1875, −4, ; 1 ,, 0 −4, 2, − 0.25 − 2, 1, 1 − 4 − 0.1875, − 0.5, − 3.5, 0.5, 1, , − 0.5, 0.5, − 3.5, 1, , 0, 2, 2, −4, , OP, PP, Q, , LM1, MM11, N0, , OP, PP, Q, , 0, 0.0625, − 0.5 − 0.5, 0, 2 − 0.1875, −4, ; R2 – R1, R3 – R1,, 0, 2, −4, − 0.25, 1, 1 − 4 − 0.1875, , LM, MM, N, , 1, 0.0625, R2, 0, − 0.25, ;, ,, − 0.3125 − 3.5 0, 0, ., − 01875, , − 0.5, 1, 0.5, 1, , − 0.5, ., − 014286, − 3.5, 1, , 0, − 0.57143, 2, −4, , OP, PP, Q, , 0.0625, 0.07143, ;, − 0.3125, ., − 01875
Page 274 :
263, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , OP, PP, Q, , LM, MM, N, , 1 − 0.5, 0, 0.0625, − 0.5, R3, R3 − 0.5 R2 , 0, 1, − 0.14286 − 0.57143 0.07143, ;, R4 − R2 ,, 0, 0, − 3.42857 2.28572 − 0.34822, − 3.42857 ,, 0, 0, 1.14286 − 3.42857 − 0.25893, , LM1, MM00, N0, , − 0.5, 1, 0, 0, , LM1, MM00, N0, , − 0.5, − 0.5, 0, 0.0625, − 0.14286 − 0.57143 0.07143 ., 1, − 0.66667 0.10156, 0, 1, − 2.66667 − 0.37500, 0, 0, , − 0.5, − 014286, ., 1, 114286, ., , 0, − 0.57143, − 0.66667, − 3.42857, , OP, PP, Q, , 0.0625, 0.07143, ;, 010156, ., − 0.25893, , R4 – 1.14286 R3,, , OP, PP, Q, , 0.37500, = 0.14062., 2.66667, Substituting in the third equation, we get u3 = 0.10156 + 0.66667(0.14062) = 0.19531., Last equation gives, , u4 =, , Substituting in the second equation, we get, u2 = 0.07143 + 0.14286(0.19531) + 0.57143(0.14062) = 0.17969., Substituting in the first equation, we get u1 = 0.5(0.17969 + 0.19531) + 0.0625 = 0.25., Iterative methods We mentioned earlier that when the order of the system of equations is, large, which is the case in most practical problems, we use iterative methods. In fact, in many, practical applications, we encounter thousands of equations. There are many powerful iterative methods available in the computer software, which are variants of successive over relaxation (SOR) method, conjugate gradient method etc. However, we shall discuss here, the implementation of the Gauss-Seidel method for the solution of the system of equations obtained in, the application of the finite difference methods. Let us recall the properties of the GaussSeidel method., (a) A sufficient condition for convergence is that the coefficient matrix A, of the system, of equations is diagonally dominant., (b) The method requires an initial approximation to the solution vector u. If no suitable, approximation is available, then u = 0 can be taken as the initial approximation., (c) Using the initial approximations, we update the value of the first unknown u1. Using, this updated value of u1 and the initial approximations to the remaining variables,, we update the value of u2. We continue until all the values are updated. We repeat, the procedure until the required accuracy is obtained., Liebmann iteration We use the above procedure to compute the solution of the difference, equations for the Laplace’s equation or the Poisson equation., The initial approximations are obtained by judiciously using the standard five point, formula (5.25)
Page 275 :
264, , NUMERICAL METHODS, , ui, j =, , 1, (u, + ui–1, j + ui, j+1 + ui, j–1), 4 i+1, j, , or the diagonal five point formula (5.28), ui, j =, , 1, (u, + ui–1, j+1 + ui+1, j–1 + ui–1, j–1), 4 i+1, j+1, , after setting the values of one or two variables as zero., If in some problems, these two formulas cannot be used (see Example 5.14), then we set the, values of required number of variables as zero., For the mesh defined in Fig. 5.12, we write the following Liebmann iteration, , ui(,kj+ 1) =, , e, , 1 ( k + 1), + ui(−k1+, 1j ) + ui(+k1) , j + ui(,kj) + 1, u, 4 i, j − 1, , where the values at the nodes (i, j – 1), (i – 1, j) are already updated (when the numbering of unknowns is from, bottom to top). If the numbering is from top to bottom,, then the iteration becomes, , ui(,kj+ 1), , e, , j, , 1 ( k + 1), =, + ui(−k1+, 1j ) + ui(,kj) −1 + ui(+k1) , j ., u, 4 i, j + 1, , j, , (5.32), i, j + 1, , i, j, i – 1, j, , i + 1, j, , Stopping criteria for iteration, We stop the iterations when the following criterion, is satisfied, ( k + 1), , | ui, , i, j – 1, , Fig. 5.12. Standard five point formula., , − u i( k ) | ≤ given error tolerance for all i., , For example, if we want two decimal places accuracy for the solution, then we iterate until, the condition, ( k + 1), , | ui, , − ui( k ) | ≤ 0.005 for all i, , (5.33), , is satisfied., Similarly, if we want three decimal places accuracy for the solution, then we iterate until, the condition, ( k + 1), , | ui, , − ui( k ) | ≤ 0.0005 for all i, , (5.34), , is satisfied., We illustrate the method through the following problems., Example 5.13 Solve uxx + uyy = 0 numerically, using five point formula and Liebmann iteration,, for the following mesh with uniform spacing and with boundary conditions as shown below in, the figure 5.13. Obtain the results correct to two decimal places., Solution We note that the boundary conditions have no symmetry. Therefore, we need to find, the values of the four unknowns u1, u2, u3 and u4. We use the standard five point formula, ui+1, j + ui–1, j, , + ui, j+1 + ui, j–1 – 4ui, j = 0.
Page 277 :
266, , NUMERICAL METHODS, , u3( 1) = 0.25 (3 + u1(1) + u4(0) ) = 0.25(3 + 1.6875 + 1.1875) = 1.46875,, u4( 1) = 0.25 (2 + u2(1) + u3(1) ) = 0.25(2 + 1.71875 + 1.46875) = 1.29688., Second iteration, , u1( 2) = 0.25 (4 + u2(1) + u3( 1) ) = 0.25(4 + 1.71875 + 1.46875) = 1.79688,, u2(2) = 0.25 (4 + u1(2) + u4(1) ) = 0.25(4 + 1.79688 + 1.29688) = 1.77344,, u3( 2) = 0.25 (3 + u1(2) + u4(1) ) = 0.25 (3 + 1.79688 + 1.29688) = 1.52344,, u4(2) = 0.25 (2 + u2(2) + u3(2) ) = 0.25(2 + 1.77344 + 1.52344) = 1.32422., Third iteration, u1(3) = 0.25 (4 + u2( 2) + u3( 2) ) = 0.25(4 + 1.77344 + 1.52344) = 1.82422,, u2(3) = 0.25 (4 + u1( 3) + u4(2) ) = 0.25(4 + 1.82422 + 1.32422) = 1.78711,, u3(3) = 0.25 (3 + u1(3) + u4(2) ) = 0.25(3 + 1.82422 + 1.32422) = 1.53711,, u4(3) = 0.25 (2 + u2(3) + u3( 3) ) = 0.25(2 + 1.78711 + 1.53711) = 1.33106., , Fourth iteration, , u1( 4) = 0.25 (4 + u2(3) + u3(3) ) = 0.25(4 + 1.78711 + 1.53711) = 1.83106,, u2( 4) = 0.25 (4 + u1(4) + u4(3) ) = 0.25(4 + 1.83106 + 1.33106) = 1.79053,, u3( 4) = 0.25 (3 + u1(4) + u4(3) ) = 0.25(3 + 1.83106 + 1.33106) = 1.54053,, u4( 4) = 0.25 (2 + u2( 4) + u3(4) ) = 0.25(2 + 1.79053 + 1.54053) = 1.33277., Fifth iteration, u1(5) = 0.25 (4 + u2( 4) + u3(4) ) = 0.25(4 + 1.79053 + 1.54053) = 1.83277,, u2(5) = 0.25 (4 + u1(5) + u4(4) ) = 0.25(4 + 1.83277 + 1.33277) = 1.79139,, u3(5) = 0.25 (3 + u1(5) + u4(4) ) = 0.25(3 + 1.83277 + 1.33277) = 1.54139,, u4(5) = 0.25 (2 + u2(5) + u3(5) ) = 0.25(2 + 1.79139 + 1.54139) = 1.33320., , At this stage, the magnitudes of the errors in the successive iterations are, |u1(5) − u1( 4) | = | 1.83277 – 1.83106 | = 0.00171,, |u2(5) − u2( 4) | = | 1.79139 – 1.79053 | = 0.00086,
Page 278 :
267, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , |u3(5) − u3( 4) | = | 1.54139 – 1.54053 | = 0.00086,, |u4(5) − u4( 4) | = | 1.33320 – 1.33277 | = 0.00043., All the errors are < 0.005. Hence, the fifth iteration values are correct to two decimal, places. We take these values as the required solutions., Example 5.14 Solve the boundary value problem, uxx + uyy = x + y + 1, 0 ≤ x ≤ 1, 0 ≤ y ≤ 1,, u = 0 on the boundary, numerically using five point formula and Liebmann iteration, with mesh length h = 1/3., Obtain the results correct to three decimal places., Solution The mesh is given in Fig.5.14. We note that all the boundary values are zero. There, is symmetry with respect the line y = x. Hence, u1 = u4. Therefore, we need to find the values, of the three unknowns u1, u2 and u3. We use the standard five point formula, ui+1, j + ui–1, j + ui, j+1 + ui, j–1 – 4ui, j = h2Gi, j =, , 1, (x + yj + 1)., 9 i, , We obtain the following difference equations., At 1:, , At 2:, , At 3:, , FG, IJ, H, K, 1 F2 2, I 7, 0 + 0 + u + u – 4u = G + + 1J =, K 27, 9 H3 3, 1F1 1, I 5, u + u + 0 + 0 – 4u = GH + + 1JK =, 9 3 3, 27, u2 + 0 + 0 + u3 – 4u1 =, , 1, , 4, , 1, , 4, , 1 1 2, 2, + +1 =, 9 3 3, 9, , 2, , 3, , or, , or, , 2u1 – 4u2 =, , 7, ., 27, , or, , 2u1 – 4u3 =, , 5, ., 27, , Using these equations, we write the difference equations, at the grid points as, u1 = 0.25(u2 + u3 – 0.222222),, , 2, ., 9, , – 4u1 + u2 + u3 =, , 0, , 0, , 0, , u1, , u2, , u3, , u4, , 0, , u2 = 0.25(2u1 – 0.259259),, u3 = 0.25(2u1 – 0.185185),, , 0, , and write the iteration procedure as, , u1( k+ 1) = 0.25 (u2( k) + u3( k) − 0.222222) ,, u2( k+ 1) = 0.25 (2u1( k+ 1) − 0.259259), ., )., u3( k +1) = 0.25 ( 2u1( k +1) − 0185185, , 0, , 0, , Fig. 5.14. Example 5.14., , 0
Page 279 :
268, , NUMERICAL METHODS, , Initial approximations Since the boundary values are all zero, we cannot use the standard or, diagonal five point formulas to obtain the initial approximations. Hence, as in Gauss-Seidel, method, we assume u2(0) = u3( 0) = 0 ., First iteration, u1( 1) = 0.25 (u2(0) + u3(0) − 0.222222) = – 0.05556,, u2( 1) = 0.25 (2u1( 1) − 0.259259) = 0.25(– 0.111112 – 0.259259) = – 0.092593,, u3( 1) = 0.25 (2u1( 1) − 0.185185) = 0.25(– 0.111112 – 0.185185) = – 0.074074., , Second iteration, u1( 2) = 0.25 (u2( 1) + u3( 1) − 0.222222) = 0.25(– 0.092593 – 0.074074 – 0.222222) = – 0.097222, u2( 2) = 0.25 (2u1(2) − 0.259259) = 0.25(– 0.194444 – 0.259259) = – 0.113426,, u3( 2) = 0.25 (2u1(2) − 0.185185) = 0.25(– 0.194444 – 0.185185) = – 0.094907., , Third iteration, u1(3) = 0.25 (u2( 2) + u3( 2) − 0.222222) = 0.25(– 0.113426 – 0.09407 – 0.222222) = – 0.107639,, u2(3) = 0.25 (2u1( 3) − 0.259259) = 0.25(– 0.215278 – 0.259259) = – 0.118634,, , u3(3) = 0.25 (2u1( 3) − 0.185185) = 0.25(– 0.215278 – 0.185185) = – 0.100116., Fourth iteration, u1( 4) = 0.25 (u2(3) + u3(3) − 0.222222) = 0.25(– 0.118634 – 0.100116 – 0.222222) = – 0.110243,, u2( 4) = 0.25 (2u1(4) − 0.259259) = 0.25(– 0.220486 – 0.259259) = – 0.119936,, u3( 4) = 0.25 (2u1(4) − 0.185185) = 0.25(– 0.220486 – 0.185185) = – 0.101418., , Fifth iteration, , u1(5) = 0.25 (u2( 4) + u3( 4) − 0.222222) = 0.25(– 0.119936 – 0.101418 – 0.222222) = – 0.110894,, u2(5) = 0.25 (2u1(5) − 0.259259) = 0.25(– 0.221788 – 0.259259) = – 0.120262,, u3(5) = 0.25 (2u1( 5) − 0.185185) = 0.25(– 0.221788 – 0.185185) = – 0.101740., Sixth iteration, u1(6) = 0.25 (u2(5) + u3( 5) − 0.222222) = 0.25(– 0.120262 – 0.101740 – 0.222222) = – 0.111056,, u2(6) = 0.25 (2u1(6) − 0.259259) = 0.25(– 0.222112 – 0.259259) = – 0.120343,, u3(6) = 0.25 (2u1(6) − 0.185185) = 0.25(– 0.222112 – 0.185185) = – 0.101824.
Page 280 :
269, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , At this stage, the magnitudes of the errors in the successive iterations are, , |u1(6) − u1(5) | = | – 0.111056 + 0.110894 | = 0.000162,, |u2(6) − u2(5) | = | – 0.120343 + 0.120262 | = 0.000081,, |u3(6) − u3(5) | = |– 101824 + 0.101740 | = 0.000084., All the errors are < 0.0005. Hence, the fifth iteration values are correct to three decimal, places. We take these values as the required solutions., Example 5.15 Using the Liebmann method, solve the equation, uxx + uyy = 0 for the following square mesh with boundary values, as shown in figure. Iterate until the maximum difference between, successive values at any point is less than 0.001., , 1, , D, , 1, , Solution The mesh is given in Fig.5.15. Number the nodes as, , u1 , u 2 , u 3 and u 4 . The partial differential equation and the, , 2, , 2, , C, , u1, , u2, , u3, , u4, , 4, , 5, , boundary values are symmetric with respect to line BD. Hence,, u2 = u3. We have three unknowns u1 , u 2 and u 4 . We use the, , A, , standard five point formula, ui+1, j + ui–1, j, , 4, , 5, , B, , Fig. 5.15. Example 5.15., , + ui, j+1 + ui, j–1 – 4ui, j = 0., , We obtain the following difference equations., At 1: u2 + 1 + 1 + u2 – 4u1 = 0,, , or, , – 2u1 + u2 = – 1., , At 2: 4 + 2 + u1 + u4 – 4u2 = 0,, , or, , u1 – 4u2 + u4 = – 6., , At 4: 5 + u2 + u2 + 5 – 4u4 = 0,, , or, , u2 – 2u4 = – 5., , Using these equations, we write the difference equations at the grid points as, u1 = 0.5(1 + u2), u2 = 0.25(6 + u1 + u4),, , u4 = 0.5(5 + u2)., , and write the iteration procedure as, u1( k+ 1) = 0.5(1 + u2( k) ) , u2( k+ 1) = 0.25(6 + u1( k+ 1) + u4( k) ) ,, , u4( k + 1) = 0.5 (5 + u2( k +1) ) ., , Initial approximations, Since the value at the corner point D is not given, we need to use the standard five point, difference formula. Hence, we set u2 = 0 and u3 = 0. We have the following initial approximations., , u1(0) = 0.25(0 + 1 + 1 + 0) = 0.5, u4(0) = 0.25(5 + 0 + 0 + 5) = 2.5 ., We can update u2 also and take the initial approximation as, u2(0) = 0.25(4 + 2 + u1(0) + u4(0) ) = 0.25(6 + 0.5 + 2.5) = 2.25., , Otherwise, u1(1) becomes same as u1(0) .
Page 281 :
270, , NUMERICAL METHODS, , First iteration, u1( 1) = 0.5 (1 + u2(0) ) = 0.5(1 + 2.25) = 1.625., u2(1) = 0.25(6 + u1(1) + u4(0) ) = 0.25(6 + 1.625 + 2.5) = 2.53125., u4(1) = 0.5 ( 5 + u 2(1) ) = 0.5( 5 + 2.53125 ) = 3.76563., , Second iteration, , ., ., u1( 2) = 0.5 (1 + u2( 1) ) = 0.5(1 + 2.53125) = 176563, u2(2) = 0.25(6 + u1( 2) + u4(1) ) = 0.25(6 + 1.76563 + 3.76563) = 2.88282., u4( 2) = 0.5 (5 + u2( 2) ) = 0.5(5 + 2.88282) = 3.94141., Third iteration, u1(3) = 0.5 (1 + u2(2) ) = 0.5(1 + 2.88282) = 1.94141., u2(3) = 0.25(6 + u1( 3) + u4( 2) ) = 0.25(6 + 1.94141 + 3.94141) = 2.97070., u4(3) = 0.5 (5 + u2(3) ) = 0.5(5 + 2.97070) = 3.98535, , Fourth iteration, , u1( 4) = 0.5 (1 + u2(3) ) = 0.5(1 + 2.97070) = 1.98535., u2( 4) = 0.25(6 + u1( 4) + u4(3) ) = 0.25 (6 + 1.98535 + 3.98535) = 2.99268., u4( 4) = 0.5 (5 + u2( 4) ) = 0.5(5 + 2.99268) = 3.99634 ., Fifth iteration, u1(5) = 0.5 (1 + u2(4 ) ) = 0.5(1 + 2.99268) = 1.99634 ., u2(5) = 0.25(6 + u1(5) + u4( 4) ) = 0.25 (6 + 1.99634 + 3.99644) = 2.99817., u4(5) = 0.5 (5 + u2(5) ) = 0.5(5 + 2.99817) = 3.99909 ., , Sixth iteration, , u1(6) = 0.5 (1 + u2(5) ) = 0.5(1 + 2.99817) = 1.99909 ., u2(6) = 0.25(6 + u1(6) + u4(5) ) = 0.25 (6 + 1.99909 + 3.99909) = 2.99955., u4(6) = 0.5 (5 + u2(6) ) = 0.5(5 + 2.99955) = 3.99977 .
Page 282 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 271, , Seventh iteration, u1(7) = 0.5 (1 + u2(6) ) = 0.5(1 + 2.99955) = 1.99978 ., u2(7) = 0.25(6 + u1(7) + u4( 6) ) = 0.25 (6 + 1.99978 + 3.99977) = 2.99989., u4(7) = 0.5 (5 + u2(7) ) = 0.5(5 + 2.99989) = 3.99994 ., , At this stage, the magnitudes of the errors in the successive iterations are, |u1(7) − u1(6) | = | 1.99978 – 1.99909 | = 0.00069,, |u2(7) − u2(6) | = | 2.99989 – 2.99955 | = 0.00034,, |u4(7) − u4(6) | = | 3.99994 – 3.99977 | = 0.00017., , All the errors are < 0.001. Hence, the seventh iteration values are taken as the required, solutions., u1 ≈ 1.99978, u2 = u3 ≈ 2.99989, u4 ≈ 3.99994., , REVIEW QUESTIONS, 1. Write the Laplace equation in two dimensions., Solution, , uxx + uyy = 0., , 2. Write the Poisson equation in two dimensions., Solution, , uxx + uyy = G(x, y)., , 3. Write the general linear second order partial differential equation in two variables., Solution Auxx + 2Buxy + Cuyy + Dux + Euy + Fu + G = 0,, where A, B, C, D, E, F, G are functions of x, y., 4. When is the linear second order partial differential equation, Auxx + 2Buxy + Cuyy + Dux + Euy + Fu + G = 0, called an elliptic or hyperbolic or parabolic equation?, Solution The given linear second order partial differential equation is called (i) an, elliptic equation when B2 – AC < 0, (ii) a hyperbolic equation when B2 – AC > 0, and (iii), a parabolic equation when B2 – AC = 0., 5. Write the standard five point formula for the solution of (i) Laplace’s equation uxx + uyy, = 0, (ii) Poisson equation uxx + uyy = G(x, y), for uniform mesh spacing h., Solution, (i), , ui+1, j + ui–1, j + ui, j+1 + ui, j–1 – 4ui, j = 0., , (ii), , ui+1, j + ui–1, j + ui, j+1 + ui, j–1 – 4ui, j = h2Gi, j., , 6. Write the diagonal five point formula for the solution of (i) Laplace’s equation uxx + uyy, = 0, (ii) Poisson equation uxx + uyy = G(x, y), for uniform mesh spacing h.
Page 283 :
272, , NUMERICAL METHODS, , Solution, (i) ui+1, j+1 + ui–1, j+1 + ui+1, j–1 + ui–1, j–1 – 4ui, j = 0., (ii) ui+1, j+1 + ui–1, j+1 + ui+1, j–1 + ui–1, j–1 – 4ui, j = 2h2Gi, j ., 6. What is the order and truncation error of the standard five point formula for the solution of, Laplace’s equation uxx + uyy = 0, with uniform mesh spacing?, Solution The method is, , ui+1, j + ui–1, j + ui, j+1 + ui, j–1 – 4ui, j = 0., , Order = 2, or O(h2)., T.E =, , F, GH, , h4 ∂ 4 u ∂ 4 u, +, 12 ∂x 4 ∂y 4, , I, JK, , + ..., i, j, , 7. What is the order and truncation error of the diagonal five point formula for the solution of, Laplace’s equation uxx + uyy = 0, with uniform mesh spacing ?, ui+1, j+1 + ui–1, j+1 + ui+1, j–1 + ui–1, j–1 – 4ui, j = 0., , Solution The method is, Order = 2,, T.E =, , h4, 6, , or O(h2)., , F∂ u + 6 ∂ u, GH ∂x ∂x ∂y, 4, , 4, , 4, , 2, , 2, , +, , ∂4u, ∂y 4, , I, JK, , + ..., i, j, , 8. When do we normally use the diagonal five point formula while finding the solution of, Laplace or Poisson equation?, Solution We use the diagonal five point formula to obtain initial approximations for, the solutions to start an iterative procedure like Liebmann iteration., 9. Finite difference methods when applied to Laplace equation or Poisson equation give, rise to a system of algebraic equations Au = d. Name the types of methods that are, available for solving these systems., Solution, (i) Direct methods like Gauss elimination method or Gauss-Jordan method can be used, when the system of equations is small., (ii) Iterative methods like Gauss-Jacobi method or Gauss-Seidel method can be used, when the system of equations is large., 10. When do we use the Liebmann method?, Solution We use the Liebmann method to compute the solution of the difference, equations for the Laplace’s equation or the Poisson equation. The initial approximations, are obtained by judiciously using the standard five point formula, ui, j =, , 1, (u, + ui–1, j + ui, j+1 + ui, j–1), 4 i+1, j, , or the diagonal five point formula, ui, j =, , 1, (u, + ui–1, j+1 + ui+1, j–1 + ui–1, j–1), 4 i+1, j+1
Page 284 :
273, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , after setting the values of one or two variables as zero. If in some problems, these two, formulas cannot be used, then we set the values of required number of variables as zero., 11. What is the condition of convergence for the system of equations obtained, when we, apply finite difference methods for Laplace’s or Poisson equation?, Solution A sufficient condition for convergence of the system of equations is that the, coefficient matrix A of the system of equations Au = d, is diagonally dominant. This, implies that convergence may be obtained even if A is not diagonally dominant., 12. What is the importance of the order of a finite difference method?, Solution When a method converges, it implies that the errors in the numerical solutions, → 0 as h → 0. Suppose that a method is of order O(h2). Then, if we reduce the step, length h by a factor, say 2, and re-compute the numerical solution using the step length, h/2, then the error becomes O[(h/2)2] = [O(h2)]/4. That is, the errors in the numerical, solutions are reduced by a factor of 4. This can easily be checked at the common points, between the two meshes., , EXERCISE 5.3, Find the solution of the Laplace equation uxx + uyy = 0 in the given region R, subject to the given, boundary conditions, using the standard five point formula., 1., , 2., –8/9, , –4/9, , –1/9, , –5/9, , u1, , u2, , u3, , u4, , 1/9, , 0, , 5/9, , –1, , 8/9, , 0, , 2, , u1, , u2, , u3, , u4, , 3, , 4/9, , Fig. 5.16. Problem 1., , 5, , 6, , 5, , Fig. 5.17. Problem 2., , 3., , 4., 400, , 200, , 100, , 500, , u1, , u2, , u3, , u4, , 100, , 200, , Fig. 5.18. Problem 3., , 3, , 500, , 0, , 400, , 0, , 6, , u1, , u2, , u3, , u4, , 0, , 0, , Fig. 5.19. Problem 4., , 6, , 3
Page 285 :
274, , NUMERICAL METHODS, , 5. R is a square of side 3 units. Boundary conditions are u(0, y) = 0, u(3, y) = 3 + y, u(x, 0), = x, u(x, 3) = 2x. Assume step length as h = 1., 6. R is a square of side 1 unit. u(x, y) = x – y on the boundary. Assume h = 1/3., Find the solution of the Poisson’s equation uxx + uyy = G(x, y) in the region R, subject to the, given boundary conditions., 7. R : 0 ≤ x ≤ 1, 0 ≤ y ≤ 1. G(x, y) = 4. u(x, y) = x2 + y2 on the boundary and h = 1/3., 8. R : 0 ≤ x ≤ 1, 0 ≤ y ≤ 1. G(x, y) = 3x + 2y. u(x, y) = x – y on the boundary and h = 1/3., 9. R : 0 ≤ x ≤ 3, 0 ≤ y ≤ 3. G(x, y) = x2 + y2 . u(x, y) = 0 on the boundary and h = 1., 10. In Problems 2, 3, 4, 8, 9, solve the system of equations using the Liebmann iteration. In, Problem 2, take the value at the top left hand point as – 2. In Problem 3, take the value, at the top left hand point as 300. In Problem 4, take the value at the top left hand point, as 0.Perform four iterations in each case., , 5.5 FINITE DIFFERENCE METHOD FOR HEAT CONDUCTION EQUATION, In section 5.3, we have defined the linear second order partial differential equation, Auxx + 2Buxy + Cuyy + Dux + Euy + Fu + G = 0, as a parabolic equation if B2 – AC = 0. A parabolic equation holds in an open domain or in a, semi-open domain. A parabolic equation together with the associated conditions is called an, initial value problem or an initial-boundary value problem. The simplest example of a parabolic equation is the following problem., Consider a thin homogeneous, insulated bar or a wire of length l. Let the bar be located, on the x-axis on the interval [0, l]. Let the rod have a source of heat. For example, the rod may, be heated at one end or at the middle point or has some source of heat. Let u(x, t) denote the, temperature in the rod at any instant of time t. The problem is to study the flow of heat in the, rod. The partial differential equation governing the flow of heat in the rod is given by the, parabolic equation, ut = c2uxx , 0 ≤ x ≤ l, t > 0., , (5.35), , c2, , where, is a constant and depends on the material properties of the rod. In order that the, solution of the problem exists and is unique, we need to prescribe the following conditions., (i) Initial condition At time t = 0, the temperature is prescribed, u(x, 0) = f(x), 0 ≤ x ≤ l., (ii) Boundary conditions Since the bar is of length l, boundary conditions at x = 0 and at, x = l are to be prescribed. These conditions are of the following types:, (a) Temperatures at the ends of the bar is prescribed, u(0, t) = g(t), u(l, t) = h(t), t > 0., (b) One end of the bar, say at x = 0, is insulated. This implies the condition that, ∂u, = 0, at x = 0 for all time t., ∂x, , (5.36)
Page 286 :
275, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , At the other end, the temperature may be prescribed, u(l, t) = h(t), t > 0., Alternatively, we may have the condition that the end of the bar at x = l is insulated., Since both initial and boundary conditions are prescribed, the problem is also called an, initial boundary value problem., For our discussion, we shall consider only the boundary conditions given in (5.36)., Mesh generation Superimpose on the domain 0 ≤ x ≤ l, t > 0, a rectangular network of mesh, lines. Let the interval [0, l] be divided into M equal parts. Then, the mesh length along the, x-axis is h = l/M. The points along the x-axis are xi = ih, i = 0, 1, 2, ..., M. Let the mesh length, along the t-axis be k and define tj = jk. The mesh points are (xi , tj) We call tj as the jth time, level (see Fig.5.20). At any point (xi , tj), we denote the numerical solution by ui, j and the exact, solution by u(xi , tj)., Remark 9 Finite difference methods are, classified into two categories: explicit, methods and implicit methods. In explicit, methods, the solution at each nodal point, on the current time level is obtained by, simple computations (additions, subtractions, multiplications and divisions), using the solutions at the previous one or, more levels. In implicit methods, we solve, a linear system of algebraic equations for, all the unknowns on any mesh line t = tj+1., When a method uses the nodal values on, two time levels tj and tj+1, as in Fig. 5.20,, then it is called a two level formula. When, a method uses the nodal values on three, time levels tj–1, tj and tj+1 then it is called a, three level formula., , t, Level j + 1, Level j, Level j – 1, , x Level 0, O, , Fig. 5.20. Nodes., , Let us derive a few methods., Explicit methods, In Chapter 2, we have derived the relationships between the derivatives and forward differences., Denote ∆t as the forward difference in the t-direction. Then, we can write Eq.(2.31) as, , LM, N, , OP, Q, , 1, 1, ∂u 1, ∆ t − ∆2t + ... u., = [log (1 + ∆ t )] u =, 2, ∂t k, k, Now, use the approximation, , FG ∂uIJ, H ∂t K, , ≈, i, j, , 1, 1, ∆ t ui, j = [ui, j + 1 − ui, j ] ., k, k, , (5.37), , (5.38)
Page 287 :
276, , NUMERICAL METHODS, , Using central differences, we also have the approximation, , F ∂ uI, GH ∂x JK, 2, , ≈, , 2, , i, j, , 1, h, , 2, , δ 2x ui, j =, , 1, h2, , [ui + 1, j − 2ui, j + ui − 1, j ] ., , (5.39), , Therefore, an approximation to the heat conduction equation (5.35) at the point (xi , tj+1), is, 1, c2, [ ui , j +1 − u i , j ] = 2 [ u i +1, j − 2ui , j + u i −1, j ] ., k, h, , ui, j+1 – ui, j = λ [ui+ 1, j − 2ui, j + ui− 1, j ], , or, or, , ui, j+1 = ui, j + λ [ui+ 1, j − 2ui, j + ui− 1, j ], , or, , ui, j+1 = λui–1, j + (1 – 2λ)ui, j + λui+1, j, , (5.40), , where λ = kc2/h2, is called the mesh ratio parameter., Note that the value ui, j+1 at the node, (xi, tj+1) is being obtained explicitly using the, values on the previous time level tj . The nodes, that are used in the computations are given in, Fig.5.21. This method is called the Schmidt, method. It is a two level method., , i, j + 1, Level j + 1, , i – 1, j, , i, j, , i + 1, j, Level j, , Truncation error of the Schmidt method, Fig. 5.21. Schmidt method., , We have the method as, ui, j+1 – ui, j = λ [ u i +1, j − 2u i , j + u i −1, j ] ., , Expanding in Taylor’s series, we obtain the left hand and right hand sides as, u( xi , t j + k) − u( xi , t j ) =, , LMRu + k ∂u + k, MNST ∂t 2, , 2, , ∂ 2u, ∂t, , 2, , OP L, PQ MN, , UV, W, , + ... − u = k, , λ [u(xi+1, tj ) – 2u(xi , tj ) + u(xi–1, tj )], =, , =, , kc 2, h2, , kc 2, h2, , OP, Q, , ∂u k 2 ∂ 2 u, +, + ..., 2 ∂t 2, ∂t, , LMRu + h ∂u + h ∂ u + h ∂ u + ...U − 2u + Ru − h ∂u + h, ST ∂x 2, MNST ∂x 2 ∂x 6 ∂x VW, LMh ∂ u + h ∂ u + ...OP = kc LM ∂ u + h ∂ u + ...OP, N ∂x 12 ∂x Q, N ∂x 12 ∂x Q, 2, , 2, , 3, , 3, , 2, , 2, , 2, , 4, , 2, , 2, , 3, , 2, , 4, , 2, , 4, , 2, , 2, , ∂ 2u, ∂x 2, , −, , UVOP, WPQ, , h3 ∂3u, + ..., 6 ∂x 3, , 4, , 4, , where all the terms on the right hand sides are evaluated at (xi , tj). The truncation error is given, by, T.E = u(xi , tj + k) – u(xi , tj) – λ[u(xi+1, tj) – 2u(xi, tj) + u(xi–1, tj)], , LM, N, , = k, , OP, Q, , LM, N, , OP, Q, , ∂u k2 ∂ 2 u, ∂ 2u h2 ∂ 4u, +, + ... − kc 2, +, + ..., 2, 2 ∂t, ∂t, ∂x 2 12 ∂x 4
Page 288 :
277, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , = k, , F ∂u − c, GH ∂t, , 2, , I, JK, , ∂2u, k 2 ∂ 2 u kh 2 c 2 ∂ 4 u, −, +, + ..., 2, ∂x, 2 ∂t 2, 12 ∂x 4, , Now, using the differential equation, , FG IJ, H K, , F I, GH JK, , F ∂ uI = c, GH ∂x JK, , F, GH, , I, JK, , ∂ ∂ 2u, ∂2, ∂ 2 u ∂ ∂u, ∂u, ∂ 2u, 4, , and 2 =, = c2, =, c, = c2, ∂t ∂x 2, ∂t ∂t, ∂x 2, ∂t, ∂t, ∂x 2, , 2, , 2, , 4, , ∂ 4u, ∂x 4, , ,, , we obtain, T.E =, , ∂ 4u, k 2 c 4 ∂ 4 u kh 2 c 2 ∂ 4u, kh 2 c 2, 6, 1, ..., (, ), −, +, =, λ, −, + ..., 2 ∂x 4, 12 ∂x 4, 12, ∂x 4, , (5.41), , The order of the method is given by, order =, , 1, (T.E) = O(h2 + k)., k, , (5.42), , Remark 10 For a fixed value of λ, that is, λ = kc 2/h 2 = fixed, we have k = λ h2/c 2 or, k = O(h2). Hence, from (5.42), for a fixed value of λ, the method is of order O(h2). That is, the, values of h and k are reduced such that the value of λ is always same., Remark 11 For λ = 1/2, Schmidt method simplifies to, ui, j+1 =, , 1, (u, + ui+1, j)., 2 i–1, j, , (5.43), , This method is also called Bender-Schmidt method. This method is also of order O(h2) for, a fixed λ., Remark 12 For λ = 1/6, the leading term in the error expression given in (5.41) vanishes. Hence,, the truncation error of the method is of the order O (k 3 + kh 4 ) . The order of the method is O(k2 +, h4). Therefore, for a fixed value of λ = 1/6, the method is of order O(h4) (see Remark 10). The, higher order method is given by, ui, j+1 =, , 1, [u, + 4ui, j + ui+1, j]., 6 i–1, j, , (5.44), , Remark 13 For the solution of a boundary value problem (for Laplace or Poisson equations),, convergence of the system of equations is important. We have noted that a sufficient condition for, the convergence of the iteration methods is that the coefficient matrix is diagonally dominant. In, the solution of an initial value problem, time t plays an important role. Theoretically, since t > 0,, we are performing infinite cycles of computation. Hence, stability of the numerical computations, plays the important role. Stability means that the cumulative effect of all errors (round-off and, other numerical errors) → 0 as computation progresses along t-axis. Analysis of the Schmidt, method gives that the method is stable if, λ=, , kc 2, h2, , ≤, , 1, ., 2, , (5.45)
Page 289 :
278, , NUMERICAL METHODS, , Note that the Bender-Schmidt method uses the value λ = 1/2. From the condition (5.45), we, find that the higher order method (5.44), which uses the value λ = 1/6, is also stable., Computational procedure, The initial condition u(x, 0) = f(x) gives the solution at all the nodal points on the initial line, (level 0). The boundary conditions u(0, t) = g(t), u(l, t) = h(t), t > 0 give the solutions at all the nodal, points on the boundary lines x = 0 and x = l , (called boundary points), for all time levels. We choose, a value for λ and h. This gives the value of the time step length k. Alternately, we may choose the, values for h and k. The solutions at all nodal points, (called interior points), on level 1 are obtained, using the explicit method. The computations are repeated for the required number of steps. If we, perform m steps of computation, then we have computed the solutions up to time tm = mk., Let us illustrate the method through some problems., Example 5.16 Solve the heat conduction equation, ut = uxx , 0 ≤ x ≤ 1, with u(x, 0) = sin (π x), 0 ≤ x ≤ 1, u(0, t) = u(1, t) = 0, using the Schmidt method. Assume h = 1/3. Compute with (i) λ = 1/2 for two time steps,, (ii) λ = 1/4 for four time steps, (iii) λ = 1/6 for six time steps. If the exact solution is, u(x, t) = exp(– π2 t) sin (π x), compare the solutions at time t = 1/9., Solution The Schmidt method is given by, ui, j+1 = λui–1, j + (1 – 2λ)ui, j + λui+1, j, We are given h = 1/3. Hence, we have four nodes on each mesh line (see Fig.5.22). We have, to find the solution at the two interior points., t, The initial condition gives the values, , FG 1 , 0IJ = u, H3 K, F2 I, u G , 0J = u, H3 K, , u, , 1, 0, , 2 ,0, , FG π IJ = 3 ,, H 3K 2, F 2π I 3 = 0.866025., = sin G J =, H3K 2, = sin, , The boundary conditions give the values u0, j = 0, u3, j = 0,, for all j., (i) We have λ = 1/2, h = 1/3, k = λh 2 = 1/18. The, computations are to be done for two time steps, that is,, upto t = 1/9. For λ = 1/2, we get the method, ui, j+1 =, , 0, , 1/3, , 2/3, , 1, , Fig. 5.22. Example. 5.16., , 1, (u, + ui+1, j ), j = 0, 1 ; i = 1, 2., 2 i–1, j, , We have the following values., For j = 0: i = 1:, , u1, 1 = 0.5(u0,0 + u2, 0) = 0.5(0 + 0.866025) = 0.433013., , i = 2:, , u2, 1 = 0.5(u1,0 + u3, 0) = 0.5(0.866025 + 0) = 0.433013., , x
Page 290 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , For j = 1: i = 1:, , u1, 2 = 0.5(u0, 1 + u2,1) = 0.5(0 + 0.433013) = 0.216507., , i = 2:, , u2, 2 = 0.5(u1,1 + u3,1) = 0.5(0.433013 + 0) = 0.216507., , 279, , After two steps t = 2k = 1/9. Hence,, u, , FG 1 , 1IJ = u FG 2 , 1IJ ≈ 0.216507., H 3 9K H 3 9K, , (ii) We have λ = 1/4, h = 1/3, k = λh2 = 1/36. The computations are to be done for four time steps,, that is, upto t = 1/9. For λ = 1/4, we get the method, ui, j+1 =, , 1, (u, + 2ui, j + ui+1, j), j = 0, 1, 2, 3 ; i = 1, 2., 4 i–1, j, , We have the following values., For j = 0: i = 1:, , u1,1 = 0.25(u0,0 + 2u1,0 + u2,0) = 0.25[0 + 3(0.866025)] = 0.649519., , i = 2:, , u2,1 = 0.25(u1,0 + 2u2,0 + u3,0) = 0.25[3(0.866025) + 0] = 0.649519., , For j = 1: i = 1:, , u1,2 = 0.25(u0,1 + 2u1,1 + u2,1) = 0.25[0 + 3(0.649519)] = 0.487139., , i = 2:, , u2,2 = 0.25(u1,1 + 2u2,1 + u3,1) = 0.25[3(0.649519) + 0] = 0.487139., , For j = 2: i = 1:, , u1,3 = 0.25(u0,2 + 2u1,2 + u2,2) = 0.25[0 + 3(0.487139)] = 0.365354., , i = 2:, , u2,3 = 0.25(u1,2 + 2u2,2 + u3,2) = 0.25[3(0.487139) + 0] = 0.365354., , For j = 3: i = 1:, , u1,4 = 0.25(u0,3 + 2u1,3 + u2,3) = 0.25[0 + 3(0.365354)] = 0.274016., , i = 2:, , u2,4 = 0.25(u1,3 + 2u2,3 + u3,3) = 0.25[3(0.365354) + 0] = 0.274016., , After four steps t = 4k = 1/9. Hence,, u, , FG 1 , 1IJ = u FG 2 , 1IJ ≈ 0.274016 ,, H 3 9K H 3 9K, , (iii) We have λ = 1/6, h = 1/3, k = λh2 = 1/54. The computations are to be done for six time steps,, that is, upto t = 1/9. For λ = 1/6, we get the method, ui, j+1 =, , 1, (u, + 4ui, j + ui+1, j ), j = 0, 1, 2, 3, 4, 5 ; i = 1, 2., 6 i–1, j, , We have the following values., For j = 0: i = 1:, , u1,1 =, , 1, 1, (u + 4u1,0 + u2,0) = [0 + 5(0.866025)] = 0.721688., 6 0,0, 6, , i = 2:, , u2,1 =, , 1, 1, (u + 4u2,0 + u3,0) = [5(0.866025) + 0] = 0.721688., 6 1,0, 6, , For j = 1: i = 1:, , u1,2 =, , 1, 1, (u0,1 + 4u1,1 + u2,1) = [0 + 5(0.721688)] = 0.601407., 6, 6, , u2,2 =, , 1, 1, (u1,1 + 4u2,1 + u3,1) = [5(0.721688) + 0] = 0.601407., 6, 6, , i = 2:
Page 291 :
280, , NUMERICAL METHODS, , For j = 2: i = 1:, , u1,3 =, , 1, 1, (u0,2 + 4u1,2 + u2,2) = [0 + 5(0.601407)] = 0.501173., 6, 6, , i = 2:, , u2,3 =, , 1, 1, (u1,2 + 4u2,2 + u3,2) = [5(0.601407) + 0] = 0.501173., 6, 6, , For j = 3: i = 1:, , u1,4 =, , 1, 1, (u0,3 + 4u1,3 + u2,3) = [0 + 5(0.501173)] = 0.417644., 6, 6, , i = 2:, , u2,4 =, , 1, 1, (u + 4u2,3 + u3,3) = [5(0.501173) + 0] = 0.417644., 6 1,3, 6, , For j = 4: i = 1:, , u1,5 =, , 1, 1, (u + 4u1,4 + u2,4) = [0 + 5(0.417644)] = 0.348037., 6 0,4, 6, , i = 2:, , u2,5 =, , 1, 1, (u + 4u2,4 + u3,4) = [5(0.417644) + 0] = 0.348037., 6 1,4, 6, , For j = 5: i = 1:, , u1,6 =, , 1, 1, (u + 4u1,5 + u2,5) = [0 + 5(0.348037)] = 0.290031., 6 0,5, 6, , i = 2:, , u2,6 =, , 1, 1, (u + 4u2,5 + u3,5) = [5(0.348037) + 0] = 0.290031., 6 1,5, 6, , After six steps t = 6k = 1/9. Hence,, u, , FG 1 , 1IJ = u FG 2 , 1IJ ≈ 0.290031., H 3 9K H 3 9K, , The magnitudes of errors at x = 1/3 and at x = 2/3 are same. The exact solution at t = 1/9 is, , u, , FG 1 , 1IJ = u FG 2 , 1IJ = exp FG − π IJ sin FG π IJ ≈ 0.289250., H 3 9 K H 3 9K H 9 K H 3 K, 2, , The magnitudes of errors are the following:, λ = 1/2 :, , | 0.216507 – 0.289250 | = 0.072743., , λ = 1/4 :, , | 0.274016 – 0.289250 | = 0.015234., , λ = 1/6 :, , | 0.290031 – 0.289250 | = 0.000781., , We note that the higher order method produced better results., Example 5.17 Solve uxx = 32 ut , 0 ≤ x ≤ 1, taking h = 0.5 and, u(x, 0) = 0, 0 ≤ x ≤ 1, u(0, t) = 0, u(1, t) = t, t > 0., Use an explicit method with λ = 1/2. Compute for four time steps., Solution The given partial differential equation is, ut =, , FG 1 IJ u, H 32 K, , xx, , and c 2 =, , 1, ., 32
Page 292 :
281, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , The step length is h = 0.25. We have five nodal, points on each mesh line (see Fig.5.23). We are to find, the solutions at three internal points., , t, , The Schmidt method is given by, ui, j+1 = λ ui–1, j + (1– 2λ)ui, j + λui+1, j., For λ = 1/2, the method becomes, ui, j+1 = 0.5 (ui–1, j + ui+1, j),, , 0, , j = 0, 1, 2, 3 ; i = 1, 2, 3., We have, , k=, , 0.25, , 0.5, , 0.75, , 1, , x, , Fig. 5.23. Example 5.17., , FG IJ, H K, , λh 2 1 1, (32) = 1., =, 2 16, c2, , The initial condition gives the values u0, 0 = u1,0 = u2,0 = u3,0 = u4,0 = 0., The boundary conditions give the values u0, j = 0, u4, j = tj = jk = j, for all j., We obtain the following solutions., For j = 0: i = 1:, , u1,1 = 0.5(u0,0 + u2,0) = 0., , i = 2:, , u2,1 = 0.5(u1,0 + u3,0) = 0., , i = 3:, , u3,1 = 0.5(u2,0 + u4,0) = 0., , For j = 1: i = 1:, , u1,2 = 0.5(u0,1 + u2,1) = 0.5(0 + 0) = 0., , i = 2:, , u2,2 = 0.5(u1,1 + u3,1) = 0.5(0 + 0) = 0., , i = 3:, , u3,2 = 0.5(u2,1 + u4,1) = 0.5(0 + 1) = 0.5., , For j = 2: i = 1:, , u1,3 = 0.5(u0,2 + u2,2) = 0.5(0 + 0) = 0., , i = 2:, , u2,3 = 0.5(u1,2 + u3,2) = 0.5(0 + 0.5) = 0.25., , i = 3:, , u3,3 = 0.5(u2,2 + u4,2) = 0.5(0 + 2) = 1.0., , For j = 3: i = 1:, , u1,4 = 0.5(u0,3 + u2,3) = 0.5(0 + 0.25) = 0.125., , i = 2:, , u2,4 = 0.5(u1,3 + u3,3) = 0.5(0 + 1.0) = 0.5., , i = 3:, , u3,4 = 0.5(u2,3 + u4,3) = 0.5(0.25 + 3) = 1.625., , The approximate solutions are u(0.25, 4) ≈ 0.125, u (0.5, 4) ≈ 0.5, u(0.75, 4) ≈ 1.625., Implicit methods, Explicit methods have the disadvantage that they have a stability condition on the mesh ratio, parameter λ. We have seen that the Schmidt method is stable for λ ≤ 0.5. This condition severely, restricts the values that can be used for the step lengths h and k. In most practical problems,, where the computation is to be done up to large value of t, these methods are not useful because, the time taken is too high. In such cases, we use the implicit methods. We shall discuss the most
Page 293 :
282, , NUMERICAL METHODS, , popular and useful method called the Crank-Nicolson method. There are a number of ways of, deriving this method. We describe one of the simple ways. Denote ∇t as the backward difference in, the time direction. From Eq.(2.32), we write the relation, k, Now, approximate k, , LM, N, , LM, N, , OP, Q, , 1, 1, ∂u, = − log (1 − ∇ t )u = ∇ t + ∇ t2 + ∇ 3t + ... u., 2, 3, ∂t, , OP LM, Q N, , ∇t, 1, ∂u, ≈ ∇ t + ∇ 2t u ≈, 2, 1 − (1/2) ∇ t, ∂t, , OP u., Q, , (5.46), (5.47), , If we expand the operator on the right hand side, we get, , LM, N, , ∇t, 1, = ∇ t 1 − ∇t, 1 − (1/2) ∇ t, 2, , OP, Q, , −1, , LM, N, , = ∇t 1 +, , OP, Q, , 1, 1, ∇ t + ∇ t2 + ..., 2, 4, , which agrees with the first two terms on the right hand side of (5.46). Applying the differential, equation at the nodal point (i, j +1), (see Fig.5.24), we obtain, , FG ∂uIJ, H ∂t K, , i, j + 1, , = c2, , F ∂ uI, GH ∂x JK, 2, , ., , 2, , (5.48), , i, j + 1, , Using the approximation given in (5.47) to left hand side and the central difference approximation (5.39) to the right hand side, we obtain, , LM, N, , OP, Q, , ∇t, 1, c2, ui, j + 1 = 2 δ 2x ui, j + 1, k 1 − (1/2) ∇ t, h, , or, or, , ∇t ui, j+1 =, , kc 2, h, , 2, , FG, H, F, = λ Gδ, H, F, = λ Gδ, H, F, = λ Gδ, H, , FG 1 − 1 ∇ IJ δ, H 2 K, t, , 2, ∇tui,j+1 = λ δ x ui, j + 1 −, , 2, x, , ui, j + 1 ,, , IJ, K, IJ ., K, , 1, ∇ t δ 2x ui, j + 1 ,, 2, , 2, x, , ui, j + 1 −, , 1 2, δ x ∇ t ui, j + 1, 2, , 2, x, , ui , j +1 −, , 1 2, δ x u i , j +1 − u i , j, 2, , 2, x, , ui, j + 1 −, , 1 2, {δ x ui, j + 1 − δ 2x, 2, , or, , ∇ t ui, j + 1, , or, , ∇t ui , j +1, , or, , ∇ t ui, j + 1, , or, , ∇ t ui, j + 1 =, , λ 2, (δ x ui, j + 1 + δ 2x ui, j ) ,, 2, , or, , ui, j + 1 − ui, j =, , λ 2, (δ x ui, j + 1 + δ 2x ui, j ) ,, 2, , or, , ui, j + 1 −, , n, , λ 2, λ, δ x ui, j +1 = ui, j + δ 2x ui, j, 2, 2, , sIJK ,, I, u }J ,, K, i, j, , (5.49)
Page 294 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , or, , ui, j + 1 −, , or, , −, , 283, , λ, λ, (ui + 1, j + 1 − 2ui, j + 1 + ui − 1, j + 1 ) = ui, j + (ui+ 1, j − 2ui, j + ui− 1, j ) ,, 2, 2, , λ, λ, ui − 1, j + 1 + (1 + λ)ui, j +1 − ui + 1,, 2, 2, , j +1, , =, , λ, λ, ui − 1, j + (1 − λ)ui, j + ui + 1, j ,, 2, 2, , (5.50), , where λ = kc2/h2. This method is called the Crank-Nicolson method., The nodal points that are used in the method are given in Fig.5.24., , l– 1, j + 1, , l, j + 1, , l + 1, j + 1, Level j + 1, , l – 1, j, , l, j, , l + 1, j, , Level j, , Fig. 5.24. Nodes in Crank-Nicolson method., , Remark 14 From the right hand side of Eq.(5.49), we note that it is the mean of the central, difference approximations, δ 2x u , to the right hand side of the differential equation on the levels j, and j + 1. This concept of taking the mean of the central difference approximations to the right, hand side of a given differential equation is often generalized to more complicated differential, equations., Remark 15 The order of the Crank-Nicolson method is O(k2 + h2)., Remark 16 Implicit methods often have very strong stability properties. Stability analysis of the, Crank-Nicolson method shows that the method is stable for all values of the mesh ratio parameter λ. This implies that there is no restriction on the values of the mesh lengths h and k., Depending on the particular problem that is being solved, we may use sufficiently large values of, the step lengths. Such methods are called unconditionally stable methods., Computational procedure The initial condition u(x, 0) = f(x) gives the solution at all the nodal, points on the initial line (level 0). The boundary conditions u(0, t) = g(t), u(l, t) = h(t), t > 0 give the, solutions at all the nodal points on the lines x = 0 and x = l for all time levels. We choose a value, for λ and h. This gives the value of the time step length k. Alternately, we may choose the values, for h and k. The difference equations at all nodal points on the first time level are written. This, system of equations is solved to obtain the values at all the nodal points on this time level. The, computations are repeated for the required number of steps. If we perform m steps of computation, then we have computed the solutions up to time tm = mk., Remark 17 Do you recognize the system of equations that is obtained if we apply the CrankNicolson method? Again, it is a tri-diagonal system of equations. It uses the three consecutive, unknowns ui–1, j+1 , ui, j+1 and ui+1, j+1 on the current time level. This is the advantage of the, method., Let us illustrate the application of the method.
Page 295 :
284, , NUMERICAL METHODS, , Example 5.18 Solve the equation ut = uxx subject to the conditions, u(x, 0) = sin (π x), 0 ≤ x ≤ 1, u(0, t) = u(1, t) = 0, using the Crank-Nicolson method with, h = 1/3, k = 1/36. Do one time step., (A.U. Nov/Dec. 2006), Solution We have, , 1, 1, 1, kc 2, 1, ,k=, ,λ= 2 =, (9) = ., 3, 36, 4, 36, h, Crank-Nicolson method is given by, c2 = 1, h =, , −, , λ, λ, ui − 1, j + 1 + (1 + λ)ui, j +1 − ui + 1,, 2, 2, , j +1, , =, , (Fig.5.25)., , λ, λ, ui − 1, j + (1 − λ)ui, j + ui + 1, j, 2, 2, , For λ = 1 / 4, we have the method as, , −, or, , 1, 5, ui −1, j + 1 + ui,, 8, 4, , − ui− 1, j + 1 + 10ui,, , j +1, , j +1, , −, , 1, 1, 3, 1, ui +1, j +1 = ui −1, j + ui, j + ui +1, j, 8, 8, 4, 8, , − ui+ 1, j + 1 = ui− 1, j + 6ui, j + ui+ 1, j ,, , j = 0 ; i = 1, 2., , The initial condition gives the values, u0,0 = 0, u1,0 = sin (π/3) = ( 3 /2) = u2,0, u3,0 = 0., The boundary conditions give the values u0, j = 0 = u3, j for all j,, We have the following equations., For j = 0, i = 1 :, , – u0,1 + 10 u1,1 – u2,1 = u0,0 + 6u1,0 + u2,0, or, , i = 2:, , 10u1,1 – u2,1 =, , 6 3, 3 7 3, = 6.06218., +, =, 2, 2, 2, , – u1,1 + 10u2,1 – u3,1 = u1,0 + 6u2,0 + u3,0, or, , Subtracting the two equations, we get 11u1,1 – 11u2,1, = 0. Hence, u1,1 = u2,1. The solution is given by, u1,1 = u2,1 =, , 3 6 3 7 3, +, =, = 6.06218., 2, 2, 2, , – u1,1 + 10u2,1 = u1,0 + 6u2,0 =, , 6.06218, = 0.67358., 9, , t, , 0, , 1/3, , 2/3, , 1, , x, , Fig. 5.25. Example 5.18., , Example 5.19 Solve uxx = ut in 0 < x < 2, t > 0,, u(0, t) = u(2, t) = 0, t > 0 and u(x, 0) = sin (π x/ 2), 0 ≤ x ≤ 2,, using ∆x = 0.5, ∆t = 0.25 for one time step by Crank-Nicolson implicit finite difference method., (A.U Apr/May 2003)
Page 296 :
285, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , c2 = 1, ∆x = 0.5, ∆t = 0.25, λ =, , Solution We have, , c 2 ∆t, ∆x, , 2, , =, , 0.25, = 1., 0.25, , Crank-Nicolson implicit finite difference method is given by, , −, , λ, λ, ui − 1, j + 1 + (1 + λ)ui, j +1 − ui + 1,, 2, 2, , j +1, , =, , λ, λ, ui − 1, j + (1 − λ)ui, j + ui + 1, j ., 2, 2, , For λ = 1, we have the method as, , −, , 1, 1, ui −1, j + 1 + 2ui, j + 1 − ui +1,, 2, 2, , j +1, , =, , 1, 1, ui −1, j + ui + 1, j, 2, 2, , − u i −1, j +1 + 4u i , j +1 − ui +1, j +1 = ui −1, j + u i + i , j , j = 0 ; i = 1, 2, 3,, , or, , The initial condition gives the values, u0,0 = 0, u1,0 = sin(π/4) = (1/ 2 ) = 0.70711,, u2,0 = sin (π/2) = 1, u3, 0 = sin (3π/4) = (1/ 2 ) = 0.70711., The boundary conditions give the values u0, j = 0 = u4, j for all j., t, , 0, , 0.5, , 1.0, , 1.5, , 2.0, , x, , Fig. 5.26. Example 5.19., , We have the following equations., For j = 0, i = 1 :, , – u0,1 + 4u1,1 – u2,1 = u0,0 + u2,0, , or, , i = 2:, , – u1,1 + 4u2,1 – u3,1 = u1,0 + u3,0, , or – u1,1 + 4u2,1 – u3,1 = 1.41421,, , i = 3:, , – u2,1 + 4u3,1 – u4,1 = u2,0 + u4,0, , or, , 4u1,1 – u2,1 = 1,, , – u2,1 + 4u3,1 = 1., , Subtracting the first and third equations, we get 4u1,1 – 4u3,1 = 0. Hence, u1,1 = u3,1. We, have the system of equations as, 4u1,1 – u2,1 = 1, and – 2u1,1 + 4u2,1 = 1.41421., Using determinants, the solution is obtained as, , 5.41421, 7.65684, = 0.38673, u2,1 =, = 0.54692., 14, 14, Example 5.20 Solve by Crank-Nicolson method the equation uxx = ut subject to, u1,1 =, , u(x, 0) = 0, u(0, t) = 0 and u(1, t) = t,, for two time steps., , (A.U Nov/Dec. 2003, Nov/Dec. 2006)
Page 297 :
286, , NUMERICAL METHODS, , Solution Since the values of the step lengths h and k are not given, let us assume h = 0.25 and, λ = 1. Hence, k = λh2 = 0.0625. (Fig. 5.27)., Crank-Nicolson implicit finite difference method is given by, , −, , λ, λ, ui − 1, j + 1 + (1 + λ)ui, j + 1 − ui + 1, j +1, 2, 2, =, , t, , λ, λ, ui − 1, j + (1 − λ)ui, j + ui + 1, j ., 2, 2, , For λ = 1, we have the method as, , −, , 1, 1, ui −1, j + 1 + 2ui, j + 1 − ui +1,, 2, 2, , 0, j +1, , =, , 0.25, , 1, 1, ui −1, j + ui + 1, j, 2, 2, , 0.5, , 0.75, , 1, , x, , Fig. 5.27. Example 5.20., , − ui −1, j +1 + 4ui , j +1 − ui +1, j +1 = ui −1, j + ui +1, j , j = 0 ; i = 1, 2, 3.., , or, , The initial condition gives the values ui, 0 = 0 for all i., The boundary conditions give the values u0, j = 0, for all j and u4, j = tj = jk = 0.0625 j., We have the following equations., For j = 0,, , i = 1 : – u0,1 + 4u1,1 – u2,1 = u0,0 + u2,0 or, , 4u1,1 – u2,1 = 0,, , i = 2 : – u1,1 + 4u2,1 – u3,1 = u1,0 + u3,0 or, , – u1,1 + 4u2,1 – u3,1 = 0,, , i = 3 : – u2,1 + 4u3,1 – u4,1 = u2,0 + u4,0 or, The system of equations is given by, , LM 4, MN− 01, , OP LM, PQ MMN, , Perform, , OP LM, PQ MN, , LM, MN, , OP, PQ, , 0, 0 u1,1, −1, 0, 4 − 1 u2,1 =, ., 0.0625, 4 u3,1, −1, , We solve this system by Gauss elimination., , LM 4, MN− 01, , OP, PP, Q, , – u2,1 + 4u3,1 = 0.0625., , OP, PQ, , LM, MN, , OP, PQ, , −1, 0, 0, 1 − 1/4, 0, 0, R, 4 −1, 0, 0, , Perform 1 , then R2 + R1. 0 15/4 − 1, ,, 4, −1, 4 0.0625, 0 −1, 4 0.0625, , LM, MN, , OP, PQ, , 1 − 1/4, 0, 0, R2, , then R3 + R2. 0, ,, 1 − 4/15, 0, (15/4), 0, 0 56/15 0.0625, , FG 15 IJ = 0.01674., H 56 K, F4I F4I, The second equation gives u = G J u = G J 0.01674 = 0.00446 ., H 15 K H 15 K, F 1I, F 1I, The first equation gives u = G J u = G J 0.00446 = 0.00112 ., H 4K, H 4K, The last equation gives u3,1 = 0.0625, , 3, 1, , 2,1, , 1,1, , 2,1
Page 298 :
287, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , For, , j = 1,, , i=1:, , – u0,2 + 4u1,2 – u2,2 = u0,1 + u2,1 = 0 + 0.00446,, 4u1,2 – u2,2 = 0.00446., , or, i = 2:, , – u1,2 + 4u2,2 – u3,2 = u1,1 + u3,1 = 0.00112 + 0.01674 = 0.01786., , i = 3:, , – u2,2 + 4u3,2 – u4,2 = u2,1 + u4,1 = 0.00446 + 0,, – u2,2 + 4u3,2 = 0.00446 + 0.125 = 0.12946., , or, , The system of equations is given by, , LM 4, MN− 01, , OP LMu, PQ MMNuu, , 0, −1, 4 −1, 4, −1, , 1, 2, , 2, 2, 3, 2, , We solve this system by Gauss elimination., , LM 4, MN− 01, , Perform, , OP, PQ, , OP L0.00446O, PP ., PP = MMN00..01786, Q 12946Q, LM, MN, 0.001115O, 0.00506P ., 0.13452PQ, , −1, 0 0.00446, 1 − 1/4, R1, 4 − 1 0.01786 . Perform, , then R2 + R1. 0 15 /4, 4, 0 −1, −1, 4 0.12946, , LM, MN, , 1 − 1/4, R2, , then R3 + R2. 0, 1, (15/4), 0, 0, , 0, − 4/15, 56/15, , OP, PQ, , 0 0.001115, − 1 0.018975 ., 4 0.12946, , FG 15 IJ 0.13452 = 0.036032., H 56 K, F4I, F 4I, The second equation gives u = G J u = G J 0.036032 = 0.014669 ., H 15 K, H 15 K, F 1I, F 1I, The first equation gives, u = G J u = G J 0.014669 = 0.004782., H 4K, H 4K, The last equation gives u3, 2 =, , 2, 2, , 1, 2, , 3,2, , 2,2, , REVIEW QUESTIONS, 1. Write the one dimensional heat conduction equation and the associated conditions., Solution The heat conduction equation is given by, ut = c2uxx, 0 ≤ x ≤ l, t > 0., The associated conditions are the following., Initial condition At time t = 0, the temperature is prescribed, u(x, 0) = f(x), 0 ≤ x ≤ l., Boundary conditions Since the bar is of length l, boundary conditions at x = 0 and at, x = l are to be prescribed., u(0, t) = g(t), u(l, t) = h(t),, , t > 0.
Page 299 :
288, , NUMERICAL METHODS, , 2. What is an explicit method for solving the heat conduction equation?, Solution In explicit methods, the solution at each nodal point on the current time level is, obtained by simple computations (additions, subtractions, multiplications and divisions), using the solutions at the previous one or more levels., 3. Write the Schmidt method for solving the one dimensional heat conduction equation., Solution The Schmidt method for solving the heat conduction equation, ut = c2uxx, 0 ≤ x ≤ l, t > 0, is given by ui, j+1 = λui–1, j + (1 – 2λ)ui, j + λui+1, j ; j = 0, 1, .... ; i = 1, 2, ..., where λ = kc2/h2, is the mesh ratio parameter and h and k are the step lengths in the x, and t directions respectively., 4. What is the order and truncation error of the Schmidt method?, Solution The order of the method is O(k + h2). For a fixed value of λ, the method behaves, like an O(h2) method. The truncation error of the method is given by, T.E =, , LM, N, , OP, Q, , ∂4u, kh 2 c 2, (6λ − 1) 4 + ..., 12, ∂x, , 5. Write the Bender-Schmidt method for solving the one dimensional heat conduction equation., Solution The Bender-Schmidt method for solving the heat conduction equation, ut = c2uxx, 0 ≤ x ≤ l, t > 0, , 1, (u, + ui+1, j). This method is a particular case of the Schmidt, 2 i–1, j, method in which we use the value λ = 1/2., is given by ui, j+1 =, , 6. Write the particular case of the Schmidt method which is of order O(k2 + h4)., Solution The higher order O(k2 + h4) method is obtained by setting λ = 1/6 in the Schmidt, method. The method is given by, , 1, [u, + 4ui, j + ui+1, j]., 6 i–1, j, For a fixed value of λ, the method behaves like an O(h4) method., ui, j+1 =, , 7. When do we call a numerical method as stable?, Solution A numerical method is said to be stable when the cumulative effect of all errors, tend to zero as the computation progresses., 8. What is the condition of stability for the Schmidt method?, Solution Schmidt method is stable when the mesh ratio parameter λ satisfies the condition λ ≤ 1/2., 9. Is the Bender-Schmidt method for solving the heat conduction equation stable?, Solution The Bender-Schmidt method is obtained from the Schmidt method by setting, λ = 1/2. Schmidt method is stable when the mesh ratio parameter λ satisfies the condition, λ ≤ 1/2. Hence, Bender-Schmidt method is also stable.
Page 300 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 289, , 10. Define an implicit method for solving the heat conduction equation., Solution In implicit methods, we solve a linear system of algebraic equations for all the, unknowns on any mesh line t = tj+1., 11. Define two level and three level methods., Solution When a method uses the nodal values on two time levels tj and tj+1, then it is, called a two level formula. When a method uses the nodal values on three time levels, tj–1, tj and tj+1, then it is called a three level formula., 12. Write the Crank-Nicolson method for solving the one dimensional heat conduction, equation., Solution The Crank-Nicolson method for solving the one dimensional heat conduction, equation ut = c2uxx, 0 ≤ x ≤ l, t > 0, is given by, ui, j+1 –, or, , −, , λ 2, λ, δ x ui, j + 1 = ui, j + δ 2x ui, j, 2, 2, , λ, λ, ui − 1, j + 1 + (1 + λ)ui, j +1 − ui + 1,, 2, 2, , j +1, , =, , λ, λ, ui − 1, j + (1 − λ)ui, j + ui + 1, j, 2, 2, , where λ = kc2/h2, is the mesh ratio parameter and h and k are the step lengths in the x, and t directions respectively., 13. What is the order of the Crank-Nicolson method for solving the heat conduction equation?, Solution The order of the Crank-Nicolson method is O(k2 + h2)., 14. What is the condition of stability for the Crank-Nicolson method?, Solution The Crank-Nicolson method is stable for all values of the mesh ratio parameter, λ. The method is also called an unconditionally stable method., 15. What type of system of equations do we get when we apply the Crank-Nicolson method to, solve the one dimensional heat conduction equation?, Solution We obtain a linear tridiagonal system of algebraic equations., , EXERCISE 5.4, 1. Solve ut = uxx, 0 ≤ x ≤ 1,with u(x, 0) = x(1 – x), 0 ≤ x ≤ 1 and u(0, t) = u(1, t) = 0 for all, t > 0. Use explicit method with h = 0.25 and λ = 0.25. Compute for four time steps., 2. Solve uxx = 16ut , 0 ≤ x ≤ 1,with u(x, 0) = x(1 – x), 0 ≤ x ≤ 1 and u(0, t) = u(1, t) = 0 for all, t > 0. Use Schmidt method with h = 0.25 and λ = 1/6. Compute for four time steps., 3. Solve uxx = 4ut , 0 ≤ x ≤ 1, with u(x, 0) = 2x for x ∈ [0, 1/2] and 2(1 – x) for x ∈ [1/2, 1]; and, u(0, t) = u(1, t) = 0 for all t > 0. Use Schmidt method with h = 0.25 and λ = 0.5. Compute for, four time steps., 4. Solve the heat conduction equation ut = uxx, 0 ≤ x ≤ 1, with u(x, 0) = sin(2π x), 0 ≤ x ≤ 1, and, u(0, t) = u(1, t) = 0 using the Schmidt method. Assume h = 0.25. Compute with, (i) λ = 1/2 for two time steps, (ii) λ = 1/4 for four time steps, (iii) λ = 1/6 for six time steps.
Page 301 :
290, , NUMERICAL METHODS, , 5. Solve ut = uxx, 0 ≤ x ≤ 5, t ≥ 0, given that u(x, 0) = 20, u(0, t) = 0, u(5, t) = 100. Compute u, for one time step with h = 1, by Crank-Nicolson method., (A.U Apr/May 2005), 6. Solve the heat equation ut = uxx, 0 ≤ x ≤ 1, subject to the initial and boundary conditions, u(x, 0) = sin (π x), 0 ≤ x ≤ 1, u(0, t) = u(1, t) = 0, using the Crank-Nicolson method with, h = 1/3, λ = 1/6. Integrate for one time step. Find, the maximum absolute error if the exact solution is u(x, t) = exp(– π2 t) sin (πx)., 7. Find the solution of the equation ut = uxx, subject to the conditions, u(x, 0) = 6x, for x ∈ [0, 1] and 6(2 – x), x ∈ [1, 2], u(0, t) = 0 = u(2, t), using the Crank-Nicolson method with h = 0.4, λ = 1/2. Integrate for one time step., 8. Solve the heat equation ut = uxx, 0 ≤ x ≤ 1, subject to the initial and boundary conditions, u(x, 0) = sin (2π x), 0 ≤ x ≤ 1, u(0, t) = u(1, t) = 0, using the Crank-Nicolson method with, h = 0.25, λ = 0.8. Integrate for two time steps., If the exact solution of the problem is u(x, t) = exp(– 4π2 t) sin (2πx), find the magnitudes of, the errors on the second time step., 9. Find the solution of the equation 16uxx = ut, 0 ≤ x ≤ 1 subject to the conditions, u(x, 0) = 1 – x, for 0 ≤ x ≤ 1, u(0, t) = 1 – t, u(1, t) = 0, using the Crank-Nicolson method with h = 0.25, λ = 1/2. Integrate for two time steps., 10. Find the solution of the equation 4ut = uxx, 0 ≤ x ≤ 1 subject to the conditions, u(x, 0) = 3x, for x ∈ [0, 1/2] and 3(1 – x), x∈ [1/2, 1], u(0, t) = 0 = u(1, t), using the Crank-Nicolson method with h = 0.25, k = 1/32. Integrate for two time steps., , 5.6, , FINITE DIFFERENCE METHOD FOR WAVE EQUATION, , In section 5.3, we have defined the linear second order partial differential equation, Auxx + 2Buxy + Cuyy + Dux + Euy + Fu + G = 0, as an hyperbolic equation if B2 – AC > 0. An hyperbolic equation holds in an open domain or in a, semi-open domain. The simplest example of an hyperbolic equation is the one dimensional wave, equation., Study of the behavior of waves is one of the important areas in engineering. All vibration, problems are governed by wave equations., Consider the problem of a vibrating elastic string of length l, located on the x-axis on the, interval [0, l]. Let u ( x, t ) denote the displacement of the string in the vertical plane. Then, the, vibrations of the elastic string is governed by the one dimensional wave equation, (5.51), utt = c2uxx, 0 ≤ x ≤ l, t > 0., 2, where c is a constant and depends on the material properties of the string, the tension T in the, string and the mass per unit length of the string., In order that the solution of the problem exists and is unique, we need to prescribe the, following conditions.
Page 302 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 291, , (i) Initial condition Displacement at time t = 0 or initial displacement is given by, u(x, 0) = f(x), 0 ≤ x ≤ l., Initial velocity:, ut(x, 0) = g(x), 0 ≤ x ≤ l., , (5.52 a), (5.53 b), , (ii) Boundary conditions We consider the case when the ends of the string are fixed. Since, the ends are fixed, we have the boundary conditions as, u(0, t) = 0, u(l, t) = 0, t > 0., (5.53), Since both the initial and boundary conditions are prescribed, the problem is called an initial, boundary value problem., Mesh generation The mesh is generated as in the case of the heat conduction equation. Superimpose on the region 0 ≤ x ≤ l, t > 0, a rectangular network of mesh lines. Let the interval [0, l] be, divided into M parts. Then, the mesh length along the x-axis is h = l/M. The points along the xaxis are xi = ih, i = 0, 1, 2, ..., M. Let the mesh length along the t-axis be k and define tj = jk. The, mesh points are (xi , tj) as given in Fig. 5.20. We call tj as the jth time level. At any point (x i , tj),, we denote the numerical solution by u i , j and the exact solution by u(xi , tj)., As in the case of the heat conduction equation, we can derive explicit and implicit methods, for the solution of the wave equation., Let us derive a few methods., Explicit methods, Using central differences, we write the approximations, , F ∂ uI, GH ∂x JK, F ∂ uI, GH ∂t JK, 2, , ≈, , 2, , i, j, , 2, , ≈, , 2, , i, j, , 1, h, , 2, , 1, k, , 2, , δ 2x ui , j =, δ t2 ui , j =, , 1, , [u i +1, j − 2u i , j + u i −1, j ] ., , (5.54), , [u i , j +1 − 2u i , j + u i , j −1 ], , (5.55), , h2, 1, k2, , Applying the differential equation (5.51) at the nodal point (xi , tj), and using the central, difference approximations, (5.54), (5.55), we get, 1, k, , 2, , [ui, j + 1 − 2ui, j + ui, j −1 ] =, , c2, h2, , [ui + 1, j − 2ui, j + ui − 1, j ], , or, , ui, j + 1 − 2ui, j + ui, j − 1 = r 2 [ui + 1, j − 2ui, j + ui − 1, j ], , or, , ui , j +1 = 2ui , j − ui , j −1 + r 2 [ui +1, j − 2u i , j + u i −1, j ], , or, , ui, j + 1 = 2(1 − r 2 )ui, j + r 2 [ui + 1, j + ui − 1, j ] − ui, j − 1, , where r = kc/h, is called the mesh ratio parameter., The nodes that are used in the computations are given in Fig.5.28., , (5.56)
Page 303 :
292, , NUMERICAL METHODS, , i, j + 1, Level j + 1, i – 1, j, , i, j, , i + 1, j, Level j, Level j – 1, , i, j – 1, , Fig. 5.28. Nodes in explicit method., , Remark 18 We note that the minimum number of levels required for any method (explicit or, implicit) is three. Therefore, the method is always a three level method. The value ui, j+1 at the, node (xi , tj+1) is being obtained by the formula in Eq. (5.56), explicitly using the values on the, previous time levels tj and tj–1., Truncation error of the explicit method, We have the method as, ui, j + 1 − 2ui, j + ui, j − 1 = r 2 [ui + 1, j − 2ui, j + ui − 1, j ] ., , Expanding in Taylor’s series, we obtain, u(xi , tj + k) – 2u(xi, tj) + u(xi , tj – k), , LMRu + k ∂u + k ∂ u + k ∂ u + k ∂ u + ...U, MNST ∂t 2 ∂t 6 ∂t 24 ∂t VW, R ∂u + k ∂ u − k ∂ u + k ∂ u − ...UVOP, − 2u + S u − k, T ∂t 2 ∂t 6 ∂t 24 ∂t WPQ, L ∂ u + k ∂ u + ...OP, = Mk, N ∂t 12 ∂t Q, 2, , 2, , =, , 3, , 3, , 2, , 4, , 3, , 2, , 2, , 4, , 3, , 3, , 2, , 2, , 2, , 4, , 2, , 4, , 4, , 3, , 4, , 4, , 4, , 4, , r2 [u(xi+1 , tj) – 2u(xi , tj) + u(xi–1 , tj)], , LMRu + h ∂u + h ∂ u + h ∂ u + h ∂ u + ...U, S ∂x 2 ∂x 6 ∂x 24 ∂x VW, h MNT, R ∂u + h ∂ u − h ∂ u + h ∂ u − ...UVOP, − 2u + Su − h, T ∂x 2 ∂x 6 ∂x 24 ∂x WPQ, L ∂ u + h ∂ u + ...OP, O, k c L ∂ u h ∂ u, h, +, + ...P = k c M, =, M, 12 ∂x, h N ∂x, MN ∂x 12 ∂x PQ, Q, =, , k2 c2, , 2, , 2, , 2, , 3, , 2, , 2, , 2, , 2 2, 2, , 2, , 2, , 4, , 2, , 4, , 3, , 3, , 2, , 3, , 4, , 3, , 4, , 3, , 4, , 2 2, , 4, , 4, , 2, , 4, , 4, , 2, , 2, , 4, , 4, , where all the terms on the right hand sides are evaluated at (xi , tj). The truncation error is given, by
Page 304 :
293, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , T.E = [u(xi , tj + k) – 2u(xi , tj) + u(xi , tj – k)] – r2 [u(xi+1 , tj) – 2u(xi , tj) + u(xi–1 , tj)], , LM, N, , = k2, , F∂ u − c, GH ∂t, 2, , = k2, , OP, Q, , LM, N, , OP, Q, , 2, h2 ∂ 4u, ∂ 2u k4 ∂ 4u, 2 2, 2 ∂ u, ..., k, c, h, −, +, + ..., +, +, ∂t 2 12 ∂t 4, ∂x 2 12 ∂x 4, , 2, , 2, , I, JK, , k4 ∂ 4 u k2 h 2 c 2 ∂ 4 u, ∂2u, +, −, + ..., 2, 12 ∂t 4, 12 ∂x 4, ∂x, , Now, using the differential equation, ∂ 2u, ∂t 2, , = c2, , ∂ 2u, ∂x 2, , and, , ∂ 4u, ∂t 4, , = c2, , we obtain, T.E. =, , ∂2, ∂t 2, , F ∂ uI = c, GH ∂x JK, 2, , 2, , 4, , ∂2, ∂x 2, , F ∂ uI = c, GH ∂x JK, 2, , 2, , F, GH, , 4, , ∂4u, ∂x 4, , I, JK, , k 4 c 4 ∂ 4 u k2 h 2 c 2 ∂ 4 u, k2 h 2 c 2, ∂4u, (r 2 − 1) 4 + ..., −, + ... =, 4, 4, 12 ∂x, 12 ∂x, 12, ∂x, , since k = (hr)/c., , (5.57), , The order of the method is given by, order =, , 1, k2, , (T.E) = O(h2 + k2)., , (5.58), , Remark 19 For a fixed value of r, that is, r = kc/h = fixed, we have k = rh/c or k = O(h). Hence, for, a fixed value of r, the method is of order O(h2). That is, the values of h and k are reduced such that, the value of r is always same., Remark 20 For r = 1, the leading term in the error expression given in (5.57) vanishes. Hence,, the truncation error of the method is of the order O(k6 + k2h4). The order of the method is, O(k4 + h4). Therefore, for the fixed value of r = 1, the method is of order O(h4). The higher order, method obtained when r = 1 is given by, , ui, j + 1 − 2ui, j + ui, j − 1 = ui+ 1, j − 2ui, j + ui− 1, j, or, , ui, j + 1 = 2ui, j − ui, j − 1 + [ui+ 1, j − 2ui, j + ui− 1, j ], = ui+ 1, j + ui−1, j − ui, j − 1 ., , (5.59), , The nodes that are used in computations are given in Fig. 5.29., , i, j + 1, Level j + 1, i – 1, j, , i + 1, j, , Level j, , Level j – 1, i, j – 1, , Fig. 5.59. Nodes in explicit method for r = 1.
Page 305 :
294, , NUMERICAL METHODS, , When the values of h and k are not prescribed in any particular problem, we may choose, these values such that r = 1., Remark 21 In the case of the wave equation also, stability of the numerical computations, plays an important role. Analysis of the method gives that the method is stable if, r=, , kc, ≤ 1., h, , (5.60), , Note that the higher order method (5.59) uses the value r = 1. Hence, the higher order, method is also stable., Computational procedure, Since the explicit method (5.56) or (5.59) is of three levels, we need data on two time levels t =, 0 and t = k, to start computations., The boundary conditions u(0, t) = g(t), u(l, t) = h(t), t > 0 give the solutions at all the, nodal points on the lines x = 0 and x = l for all time levels. We choose a value for k and h. This, gives the value of r. Alternately, we may choose the values for h and r. For r = 1, and c = 1, we, have h = k., The initial condition u(x, 0) = f(x) gives the solution at all the nodal points on the initial, line (level 0). The values required on the level t = k is obtained by writing a suitable approximation to the initial condition, , ∂u, ( x, 0) = g( x) ., ∂t, If we write the central difference approximation, we obtain, ∂u, 1, ( x, 0) ≈, [ui,1 − ui,−1 ] = g ( xi ) ., (5.61), 2k, ∂t, This approximation introduces the external points ui ,–1. Solving for ui , –1 from (5.61), we get, ui ,–1 = ui,1 – 2kg(xi)., , (5.62), , Now, we use the method (5.56) or (5.59) at the nodes on the level t = k, that is, for j = 0., We get, ui,1 = 2(1 − r 2 )ui,0 + r 2 [ui +1,0 + ui −1,0 ] − ui −1 ., , (5.63 a), , The external points u i ,−1 , that are introduced in this equation are eliminated by using, the relation in (5.62)., ui,1 = 2(1 – r2)ui,0 + r2 [ui+1,0 + ui−1,0 ] − [ui,1 − 2kg ( xi )], or, , 2ui,1 = 2(1 – r2)ui,0 + r2 [ui+ 1,0 + ui− 1,0 ] + 2kg( xi ) ., , (5.63 b), , This gives the values at all nodal points on the level t = k., For example, if the initial condition is prescribed as, (5.62), ui, –1 = ui,1. The formula (5.63b) becomes, , ∂u, ( x, 0) = 0 , then we get from, ∂t
Page 306 :
295, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 2ui,1 = 2(1 – r2)ui,0 + r2 [ui+1,0 + ui–1,0], ui,1 = (1 – r2)ui,0 +, , or, , r2, [ui+1,0 + ui–1,0]., 2, , (5.64), , For r = 1, the method simplifies to, ui,1 =, , 1, [u, + ui–1,0]., 2 i+1,0, , (5.65), , Thus, the solutions at all nodal points on level 1 are obtained. For t > k, that is for j ≥ 1,, we use the method (5.56) or (5.59). The computations are repeated for the required number of, steps. If we perform m steps of computation, then we have computed the solutions up to time, tm = mk., Let us illustrate the method through some problems., Example 5.21 Solve the wave equation, utt = uxx , 0 ≤ x ≤ 1, subject to the conditions, u(x, 0) = sin (π x), ut (x, 0) = 0, 0 ≤ x ≤ 1, u(0, t) = u(1, t) = 0, t > 0, using the explicit method with h = 1/4 and (i) k = 1/8, (ii) k = 1/4. Compute for four time steps for, (i), and two time steps for (ii). If the exact solution is u(x, t) = cos (π t) sin (π x), compare the, solutions at times t = 1/4 and t = 1/2., Solution The explicit method is given by, , ui, j +1 = 2(1 – r2)ui,j + r2 [ui+1,j + ui–1, j] – ui, j–1., We are given c = 1 and h = 1/4. Hence, we have five nodes on each time level (see, Fig.5.30). We have to find the solution at three interior points., The initial conditions give the values, (a) ui,0 = sin (i π /4), i = 0, 1, 2, 3, 4, u0, 0 = 0, u1, 0 = sin (π/4) = (1/ 2 ) = 0.70711, u2,0 = sin (π /2) = 1,, u3,0 = sin (3π /4) = (1/ 2 ) = 0.70711, u4,0 = sin (π) = 0., (b) ut(x, 0) = 0 gives ui,–1 = ui, 1., The boundary conditions give the values u0, j = 0, u4, j = 0, for all j., (i) When k = 1/8, we get r =, becomes, , FG, H, , ui, j+1 = 2 1 −, , k 1, 1, = (4) = . The method, h 8, 2, , t, , IJ, K, , 1, 1, ui, j + [ui + 1, j + ui − 1, j ] − ui, j − 1, 4, 4, , = 1.5ui, j + 0.25[ui+1, j + ui–1, j] – ui, j–1 ,, j = 0, 1, 2, 3 ; i = 1, 2, 3., , (5.66), , The computations are to be done for four time, steps, that is, up to t = 1/2 or j = 0, 1, 2, 3., , 0, , 0.25, , 0.5, , 0.75, , 1.0, , Fig. 5.30. Example. 5.21., , x
Page 307 :
296, , NUMERICAL METHODS, , We have the following values., For, , j = 0 : Since ut(x, 0) = 0 we obtain ui, –1 = ui, 1. The method simplifies to, ui,1 = 0.75ui,0 + 0.125[ui+1,0 + ui–1,0]., i=1:, , u1,1 = 0.75u1,0 + 0.125(u2,0 + u0,0), = 0.75(0.70711) + 0.125(1 + 0) = 0.65533., , i=2:, , u2,1 = 0.75u2,0 + 0.125(u3,0 + u1,0), = 0.75 + 0.125(0.70711 + 0.70711) = 0.92678., , i=3:, , u3,1 = 0.75u3,0 + 0.125(u4,0 + u2,0), = 0.75(0.70711) + 0.125(0 + 1) = 0.65533., , For, , j = 1: We use the formula (5.66)., i=1:, , u1,2 = 1.5u1,1 + 0.25[u2,1 + u0,1] – u1,0, = 1.5(0.65533) + 0.25(0.92678 + 0) – 0.70711 = 0.50758., , i=2:, , u2,2 = 1.5 u2,1 + 0.25[u3,1 + u1,1] – u2,0, = 1.5(0.92678) + 0.25(0.65533 + 0.65533) – 1.0 = 0.71784., , i=3:, , u3,2 = 1.5u3,1 + 0.25[u4,1 + u2,1] – u3,0, = 1.5(0.65533) + 0.25(0 + 0.92678) – 0.70711 = 0.50758., , For, , j=2:, i=1:, , u1,3 = 1.5u1,2 + 0.25[u2,2 + u0,2] – u1,1, = 1.5(0.50758) + 0.25(0.71784 + 0) – 0.65533 = 0.28550., , i=2:, , u2,3 = 1.5u2,2 + 0.25[u3,2 + u1,2] – u2,1, = 1.5(0.71784) + 0.25(0.50788 + 0.50788) – 0.92678 = 0.40377., , i=3:, , u3,3 = 1.5u3,2 + 0.25[u4,2 + u2,2] – u3,1, = 1.5(0.50758) + 0.25(0 + 0.717835) – 0.65538 = 0.28550., , For, , j=3:, i=1:, , u1,4 = 1.5u1,3 + 0.25[u2,3 + u0,3] – u1,2, = 1.5(0.285499) + 0.25(0.403765 + 0) – 0.50758 = 0.02161., , i=2:, , u2,4 = 1.5u2,3 + 0.25[u3,3 + u1,3] – u2,2, = 1.5(0.4037625) + 0.25(2)(0.285499) – 0.717835 = 0.03056., , i=3:, , u3,4 = 1.5u3,3 + 0.25[u4,3 + u2,3] – u3,2, = 1.5(0.285499) + 0.25(0 + 0.40377) – 0.50758 = 0.02161.
Page 308 :
297, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , k 1, = (4) = 1. The computations are to be done for two time, h 4, steps, that is, up to t = 1/2 or j = 0, 1. For r = 1, we get the method as, (ii) When k = 1/4, h = 1/4, we get r =, , ui , j +1 = u i −1, j + ui +1, j − ui , j −1 ,, , j = 0, 1 ; i = 1, 2, 3., , (5.67), , We have the following values., For, , j = 0 : ui,–1 = ui, 1, simplifies the method as, ui,1 = ui–1,0 + ui+1,0 – ui,1, or ui, 1 = 0.5(ui–1,0 + ui+1,0)., , For, , i=1:, , u1,1 = 0.5(u0,0 + u2,0) = 0.5[0 + 1] = 0.5., , i=2:, , u2,1 = 0.5(u1,0 + u3,0) = 0.5(2)(0.70711) = 0.70711., , i=3:, , u3,1 = 0.5(u2,0 + u4,0) = 0.5(1 + 0) = 0.5., , j = 1 : We use the formula (5.67)., i=1:, , u1, 2 = u0, 1 + u2,1 – u1,0 = 0 + 0.70711 – 0.70711 = 0.0, , i=2:, , u2,2 = u1,1 + u3,1 – u2,0 = 0.5 + 0.5 – 1.0 = 0.0., , i=3:, , u3,2 = u2,1 + u4,1 – u3,0 = 0.70711 + 0 – 0.70711 = 0.0., , The exact solution and the magnitudes of errors are as follows:, At t = 0.25 : u(0.25, 0.25) = u(0.75, 0.25) = 0.5, u(0.5, 0.25) = 0.70711., For r = 1/2: The magnitudes of errors are the following:, | u(0.25, 0.25) – u1,2| = | 0.50758 – 0.5 | = 0.00758,, | u(0.5, 0.25) – u2,2 | = | 0.717835 – 0.70711 | = 0.0107,, | u(0.75, 0.25) – u3,2 | = | 0.50758 – 0.5 | = 0.00758., For r = 1, we obtain the exact solution., At t = 0.5 : u(0.25, 0.5) = u(0.75, 0.5) = u(0.5, 0.5) = 0.0., For r = 1/2 : The magnitudes of errors are 0.02161, 0.03056, and 0.02161., For r = 1, we obtain the exact solution., Example 5.22 Solve utt = 4uxx , with boundary conditions u(0, t) = 0 = u(4, t), t > 0 and the, initial conditions ut(x, 0) = 0, u(x, 0) = x(4 – x)., t, (A.U., Nov/Dec 2006), Solution We have c2 = 4. The values of the step, lengths h and k are not prescribed. The number of, time steps up to which the computations are to be, performed is not prescribed. Therefore, let us assume, that we use an explicit method with h = 1 and, k = 0.5. Let the number of time steps up to which, the computations are to be performed be 4. Then,, we have, , x, 0, , 1.0, , 2.0, , 3.0, , 4.0, , Fig. 5.31. Example 5.22.
Page 309 :
298, , NUMERICAL METHODS, , ck 2(0.5), = 1., =, h, 1, The explicit formula is given by (see (5.59)), r=, , ui, j + 1 = ui+ 1, j + ui− 1, j − ui, j −1. , j = 0, 1, 2, 3 ; i = 1, 2, 3., , (5.68), , The boundary conditions give the values u0, j = 0, u4, j = 0, for all j (see Fig. 5.31)., The initial conditions give the following values., u(x, 0) = x(4 – x), gives u0,0 = 0, u1,0 = u(1, 0) = 3,, u2,0 = u(2, 0) = 4, u3,0 = u(3, 0) = 3, u4,0 = u(4, 0) = 0., Central difference approximation to ut(x, 0) = 0 gives ui,–1 = ui,1., We have the following results., For, , j = 0: Since, ui,–1 = ui,1, the formula simplifies to ui,1 = 0.5(ui+1,0 + ui–1,0)., i=1:, , u1,1 = 0.5(u2,0 + u0,0) = 0.5(4 + 0) = 2,, , i=2:, , u2,1 = 0.5(u3,0 + u1,0) = 0.5(3 + 3) = 3,, , i = 3:, , u3,1 = 0.5(u4,0 + u2,0) = 0.5(0 + 4) = 2., , These are the solutions at the interior points on the time level t = 0.5., For j = 1: We use the formula (5.68), to give ui,2 = ui+1,1 + ui–1,1 – ui, 0., i = 1:, , u1,2 = u2,1 + u0,1 – u1,0 = 3 + 0 – 3 = 0,, , i = 2:, , u2,2 = u3,1 + u1,1 – u2,0 = 2 +2 – 4 = 0,, , i = 3:, , u3,2 = u4,1 + u2,1 – u3,0 = 0 + 3 – 3 = 0., , These are the solutions at the interior points on the time level t = 1.0., For j = 2: We use the formula (5.68), to give ui,3 = ui+1,2 + ui–1,2 – ui,1., i = 1:, , u1,3 = u2,2 + u0,2 – u1,1 = 0 + 0 – 2 = – 2,, , i = 2:, , u2,3 = u3,2 + u1,2 – u2,1 = 0 + 0 – 3 = – 3,, , i = 3:, , u3,3 = u4,2 + u2,2 – u3,1 = 0 + 0 – 2 = – 2., , These are the solutions at the interior points on the time level t = 1.5., For j = 3: We use the formula (5.68), to give ui,4 = ui+1,3 + ui–1,3 – ui,2., i = 1:, , u1,4 = u2,3 + u0,3 – u1,2 = – 3 + 0 – 0 = – 3,, , i = 2:, , u2,4 = u3,3 + u1,3 – u2,2 = – 2 – 2 – 0 = – 4,, , i = 3:, , u3,4 = u4,3 + u2,3 – u3,2 = 0 – 3 – 0 = – 3., , These are the solutions at the interior points on the required fourth time level t = 2.0., Example 5.23 Solve uxx = utt , 0 < x < 1, t > 0, given u(x, 0) = 0, ut(x, 0) = 0, u(0, t) = 0 and, u(1, t) = 100 sin (π t). Compute for four time steps with h = 0.25., (A.U. Nov/Dec. 2003)
Page 310 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 299, , Solution We have c = 1 and h = 0.25, (see Fig. 5.30). The value of the step length k is not, prescribed. Since the method is not specified, we use an explicit method., We assume k = 0.25 so that r = 1. The method is given by, , ui , j +1 = u i +1, j + u i −1, j − ui , j −1 , j = 0, 1, 2, 3; i = 1, 2, 3., The boundary conditions give the values, u0, j = 0, for all j, and u4, j = 100 sin (π jk) = 100 sin (π j/4)., That is,, , u4,0 = 0, u4, 1 = 100 sin (π /4) = (100/ 2 ) = 50 2 ,, u4,2 = 100 sin (π/2) = 100,, u4,3 = 100 sin (3π /4) = (100/ 2 ) = 50 2 , u4,4 = 100 sin (π) = 0., , For, , j = 0: Since, u i ,–1 = u i, 1, the formula simplifies to ui,1 = 0.5(ui+1,0 + ui–1,0)., i = 1:, , u1,1 = 0.5(u2,0 + u0,0) = 0.5(0 + 0) = 0,, , i = 2:, , u2,1 = 0.5(u3,0 + u1,0) = 0.5(0 + 0) = 0, , i = 3:, , u3,1 = 0.5(u4,0 + u2,0) = 0.5(0 + 0) = 0., , These are the solutions at the interior points on the time level t = 0.25., For, , j = 1: We use the formula (5.68), to give ui,2 = ui+1,1 + ui–1,1 – ui,0., i = 1:, , u1,2 = u2,1 + u0,1 – u1,0 = 0,, , i = 2:, , u2,2 = u3,1 + u1,1 – u2,0 = 0,, , i = 3:, , u3,2 = u4,1 + u2,1 – u3,0 = 50 2 + 0 – 0 = 50 2 ., , These are the solutions at the interior points on the time level t = 0.5., For, , j = 2: We use the formula (5.68), to give ui,3 = ui+1,2 + ui–1,2 – ui,1., i = 1:, , u1,3 = u2,2 + u0,2 – u1,1 = 0 + 0 + 0 = 0,, , i = 2:, , u2,3 = u3,2 + u1,2 – u2,1 = 50 2 + 0 – 0 = 50 2 ,, , i = 3:, , u3,3 = u4,2 + u2,2 – u3,1 = 100 + 0 – 0 = 100., , These are the solutions at the interior points on the time level t = 0.75., For, , j = 3: We use the formula (5.68), to give ui,4 = ui+1,3 + ui–1,3 – ui,2., i = 1:, , u1,4 = u2,3 + u0,3 – u1,2 = 50 2 + 0 – 0 = 50 2 ,, , i = 2:, , u2,4 = u3,3 + u1,3 – u2,2 = 100 + 0 – 0 = 100,, , i = 3:, , u3,4 = u4,3 + u2,3 – u3,2 = 50 2 + 50 2 – 50 2 = 50 2 ., , These are the solutions at the interior points on the required fourth time level t = 1.0.
Page 311 :
300, , NUMERICAL METHODS, , Implicit methods, Explicit methods have the disadvantage that they have a stability condition on the mesh ratio, parameter r = (ck)/h. Explicit methods are stable for r ≤ 1.0. This condition restricts the values, that can be used for the step lengths h and k. In most practical problems, where the computation is to be done up to a large value of t, these methods are not useful because the time, consumed is too high. In such cases, we use the implicit methods. We derive the following two, implicit methods., (i) We write the following approximations at (xi , tj)., , F ∂ uI, GH ∂t JK, F ∂ uI, GH ∂x JK, 2, , =, , 2, , i, j, , 2, , =, , 2, , i, j, , 1, k2, 1, 2h 2, , δ t2 ui, j ., , (5.69), , δ 2x [u i , j +1 + ui , j −1 ]., , (5.70), , Hence, the difference approximation to the wave equation at the node (xi , tj ) is given by, 1, k2, , δ 2t ui, j =, , c2, 2h 2, , δ 2x [ui, j + 1 + ui, j − 1 ],, , ui, j + 1 − 2ui, j + ui, j −1 =, , or, or, , ui , j +1 −, , or, , δ 2t ui, j =, , r2 2, δ x [ui, j + 1 + ui, j − 1 ], 2, , (5.71), , r2 2, [ δ x ui , j +1 + δ 2x u i , j −1 ], 2, , r2 2, r2 2, δ x u i , j +1 = 2u i , j −1 − ui , j −1 +, δ x ui , j −1 ., 2, 2, , (5.72), , where r = (kc/h). We can expand the central differences and write, δ 2x ui , j +1 = ui +1, j +1 − 2u i , j +1 + ui −1, j +1 ,, , δ 2x ui , j −1 = ui +1, j −1 − 2ui , j −1 + ui −1, j −1 ., We get, –, , r2, r2, r2, r2, ui + 1, j + 1 + (1 + r 2 )ui, j + 1 −, ui − 1, j + 1 = 2ui, j +, ui + 1, j − 1 − (1 + r 2 )ui, j − 1 +, ui −1,, 2, 2, 2, 2, , The nodal points that are used in the method are given in Fig.5.32., , i – 1, j + 1, , i, j + 1, , i + 1, j + 1, , Level j + 1, , i, j, Level j, , Level j – 1, i – 1, j – 1, , i, j – 1, , i + 1, j – 1, , Fig. 5.32. Nodes in implicit method (5.72)., , j −1 .
Page 312 :
301, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , Remark 22 Using Taylor series expansions, we can show that the truncation error of the, method given in Eq.(5.72) is O(k4 + k2h2). Hence, the order of the method is O(k2 + h2)., (ii) We use the approximation (5.69) for, , F ∂ uI, GH ∂x JK, 2, , =, , 2, , i, j, , 1, h2, , ∂ 2u, ∂t 2, , , and the following approximation for, , ∂ 2u, ∂x 2, , ., , δ 2x [ui, j + 1 − ui, j + ui, j − 1 ] ., , The difference approximation to the wave equation at the node (xi , tj) is given by, 1, k, , or, or, or, , 2, , δ 2t ui, j =, , c2, h, , 2, , δ 2x [ui, j + 1 − ui, j + ui, j −1 ], , δ 2t ui, j = r 2 δ 2x [ui, j + 1 − ui, j + ui, j − 1 ], , (5.73), , ui , j +1 − 2ui , j + u i, j −1 = r 2 [ δ 2x ui , j +1 − δ 2x u i, j + δ 2x u i, j −1 ], ui , j +1 − r 2 δ 2x ui , j +1 = 2ui , j − ui , j −1 − r 2 δ 2x u i, j + r 2 δ 2x ui , j −1, , (5.74), , where r = (kc/h). We can expand the central differences and write, , δ 2x ui , j +1 = ui +1, j +1 − 2u i, j +1 + ui −1, j +1 , δ 2x ui , j −1 = ui +1, j −1 − 2u i, j −1 + u i −1, j −1 ., The nodal points that are used in the method are given in Fig.5.33., Remark 23 Using Taylor series expansions, we can show that the truncation error of the, method given in Eq.(5.73) is again of order O(k4 + k2h2). Hence, the order of the method is, O(k2 + h2)., Remark 24 Implicit methods often have very strong stability properties. Stability analysis of, the above implicit methods (5.72) and (5.74) shows that the methods are stable for all values, of the mesh ratio parameter r . Hence, the methods are unconditionally stable. This implies, that there is no restriction on the values of the mesh lengths h and k. Depending on the, particular problem that is being solved, we may use sufficiently large values of the step lengths., , i – 1, j + 1, , i – 1, j, , i, j + 1, , i + 1, j + 1, , i, j, , i + 1, j, , i, j – 1, , i + 1, j – 1, , Level j + 1, , Level j, Level j – 1, , i – 1, j – 1, , Fig. 5.33. Nodes in implicit method (5.74).
Page 313 :
302, , NUMERICAL METHODS, , Computational procedure, The initial condition u(x, 0) = f(x) gives the solution at all the nodal points on the initial line, (level 0). The boundary conditions u(0, t) = g(t), u(l, t) = h(t), t > 0 give the solutions at all the, nodal points on the lines x = 0 and x = l for all time levels. We choose the values for k and h., This gives the value of the mesh ratio parameter r. Alternately, we may choose the values for, r and h., On level 1, we use the same approximation as in the case of the explicit method, that is, we, approximate, ui,–1 = ui,1 – 2kg(xi)., Now, we apply the finite difference method (5.72) or (5.74) on level 1., For example, consider the method given in (5.72). We obtain for j = 0,, , or, or, , ui ,1 −, , r2 2, r2 2, δ x u i ,1 = 2u i ,0 − ui ,−1 +, δ x u i ,−1, 2, 2, , ui,1 –, , r2 2, r2 2, δ x u i ,1 = 2ui ,0 − ( ui ,1 − 2kg i ) +, δ x ( u i ,1 − 2kg i ), 2, 2, , 2ui,1 − r 2 (ui + 1,1 − 2ui,1 + ui − 1,1 ) = 2ui,0 + 2 kgi − kr 2 ( gi + 1 − 2 gi + gi − 1 )., , (5.75), , If the initial condition is, ut(x, 0) = 0, then the method simplifies as, – r 2 ui − 1,1 + 2(1 + r 2 )ui,1 − r 2 ui + 1,1 = 2ui,0 ., , (5.76), , The right hand side in (5.75) or (5.76) is computed. For i = 1, 2,…, M – 1, we obtain a, system of equations for u1,1, u2,1, ..., uM–1, 1. This system of equations is solved to obtain the, values at all the nodal points on the time level 1. For j > 0, we use the method (5.72) or (5.74), and solve a system of equations on each mesh line. The computations are repeated for the, required number of steps. If we perform m steps of computation, then we have computed the, solutions up to time tm = mk., Remark 25 Do you recognize the system of equations that is obtained on each time level?, Again, it is a tri-diagonal system of equations. It uses the three consecutive unknowns ui–1,j+1,, ui, j+1 and ui+1, j+1 on the current time level j + 1., Let us illustrate the application of the methods., Example 5.24 Solve the wave equation, utt = uxx, 0 ≤ x ≤ 1, subject to the conditions, u(x, 0) = sin(π x), ut(x, 0) = 0, 0 ≤ x ≤ 1, u(0, t) = u(1, t) = 0, t > 0., Use an implicit method with h = 1/4 and k = 1/4. Compute for two time levels., Solution We have, c = 1, h =, , kc 1, 1, 1, = (4) = 1., ,k= ,r=, h h, 4, 4, , (Fig.5.34).
Page 315 :
304, , NUMERICAL METHODS, , For j > 0, we use the method (5.72)., , ui , j +1 −, , r2 2, r2 2, δ x u i , j +1 = 2u i , j − u i , j −1 +, δ x ui , j −1, 2, 2, , or, , ui, j + 1 −, , r2, (ui + 1, j + 1 − 2ui, j + 1 + ui −1,, 2, , = 2ui, j − ui, j − 1 +, For, , j +1), , r2, (ui +1, j − 1 − 2ui, j − 1 + ui − 1,, 2, , j −1 ) ., , j = 1, we get (with r = 1), i = 1:, , – 0.5u0,2 + 2u1,2 – 0.5u2,2 = 2u1,1 – 2u1,0 + 0.5(u2,0 + u0,0), 2u1,2 – 0.5u2,2 = 2(0.54692) – 2(0.70711) + 0.5(1.0 + 0) + 0.5(0) = 0.17962., , or, i = 2:, , – 0.5u1,2 + 2u2,2 – 0.5u3,2 = 2u2,1 – 2u2,0 + 0.5(u3,0 + u1,0), = 2(0.77364) – 2(1) + 0.5(2)(0.70711) = 0.25403., , i = 3:, or, , – 0.5u2,2 + 2u3,2 – 0.5u4,2 = 2u3,1 – 2u3,0 + 0.5(u4,0 + u2,0), – 0.5u2,2 + 2u3,2 = 2(0.54692) – 2(0.70711) + 0.5(0 + 1.0) + 0.5(0) = 0.17962., , Subtracting the first and third equations, we get 2u1,2 – 2u3,2 = 0. Hence, u1,2 = u3,2., Therefore, we have the equations, 2u1,2 – 0.5u2,2 = 0.17962, and, , – u1,2 + 2u2,2 = 0.25403., , The solution is given by, u1,2 =, , 0.486255, 0.68768, = 013893, = u3,2 , u2,2 =, ., = 0.19648., 3.5, 3.5, , REVIEW QUESTIONS, 1. Write the one dimensional wave equation governing the vibrations of an elastic string., Solution The one dimensional wave equation governing the vibrations of an elastic, string is given by, utt = c2uxx , 0 ≤ x ≤ l, t > 0., where c2 depends on the material properties of the string, the tension T in the string, and the mass per unit length of the string., 2. Write an explicit method for solving the one dimensional wave equation, utt = c2uxx , 0 ≤ x ≤ l, t > 0., Solution An explicit method for solving the one dimensional wave equation is given, by, ui , j +1 = 2(1 − r 2 )u i , j + r 2 [ u i +1, j + ui −1, j ] − u i , j −1 , j = 0, 1, 2,..., i = 1, 2, 3,...
Page 316 :
305, , BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , where r = (kc)/h, and h and k are step lengths in the x direction and t directions, respectively., 3. What is the order and truncation error of the method given in Problem 2?, Solution The order of the method is O(k2 + h2). The truncation error is given by, T.E. =, , LM, N, , OP, Q, , k2 h2 c 2, ∂4u, (r 2 − 1) 4 + ... ., 12, ∂x, , 4. Write an explicit method for solving the one dimensional wave equation, utt = c2uxx , 0 ≤ x ≤ l, t > 0, when, , r = [(kc)/h] = 1., , Solution The method is given by, , ui, j + 1 = ui+ 1, j + ui− 1, j − ui, j − 1 ., 5. For what values of r = [(kc)/h] is the explicit method for the one dimensional wave, equation stable?, Solution The explicit method is stable for r ≤ 1., 6. For what values of λ, the explicit method for solving the hyperbolic equation, ∂ 2u, ∂x, , 2, , =, , c∆t, 1 ∂ 2u, is stable, where λ =, ?, ∆x, c 2 ∂t 2, , (A.U. Apr/May 2003), , Solution For λ ≤ 1., 7. What do you mean by error in error analysis?, , (A.U. Nov/Dec. 2003), , Solution In error analysis, error means the truncation error of the method. We write, the Taylor series expansions of all the terms in the method and simplify. The leading, term of this series (the first non-vanishing term) is called the truncation error., 8. Write an implicit method for solving the one dimensional wave equation, utt = c2uxx, 0 ≤ x ≤ l, t > 0., Solution An implicit method is given by, , ui, j + 1 −, or, , –, , r2 2, r2 2, δ x ui, j + 1 = 2ui, j − ui, j −1 +, δ x ui, j −1, 2, 2, , r2, r2, ui +1, j +1 + (1 + r 2 )ui, j + 1 −, ui − 1, j + 1, 2, 2, , r2, r2, ui + 1, j − 1 − (1 + r 2 )ui, j − 1 +, ui − 1, j − 1, 2, 2, j = 0, 1, 2, ...; i = 1, 2, 3, ..., = 2ui, j +, , 9. For what values of r = [(kc)/h] is the implicit method for the one dimensional wave, equation stable?
Page 317 :
306, , NUMERICAL METHODS, , Solution The implicit method is stable for all value of r, that is, the method is unconditionally stable., 10. What type of system of equations do we get when we apply the implicit method to solve, the one dimensional wave equation?, Solution We obtain a linear tridiagonal system of algebraic equations. It uses the, three consecutive unknowns ui–1,j+1, ui, j+1 and ui+1,j+1 on the current time level j + 1., , EXERCISE 5.5, 1. Solve the wave equation utt = uxx , 0 < x < 1, t > 0 with u (0, t ) = u (1, t ) = 0 and u(x, 0) = sin, (π x), and ut(x, 0) = 0, 0 ≤ x ≤ 1, with ∆x = 0.25, and ∆t = 0.25 for three time steps., 2. Solve ytt = yxx, up to t = 0.5 with a spacing of 0.1, subject to y (0, t ) = 0, y (1, t ) = 0,, , y t ( x,0) = 0, and y(x, 0) = 10 + x(1 – x)., , (A.U. Nov/Dec. 2004), , 3. Approximate the solution of the wave equation utt = uxx, 0 < x < 1, t > 0, u(0, t) = u(1, t) = 0 and u(x, 0) = sin (2π x), and ut (x, 0) = 0, 0 ≤ x ≤ 1,, with ∆x = 0.25, and ∆t = 0.25 for three time steps., (A.U. Apr/May 2003, Nov/Dec. 2004), 4. Solve uxx = utt, 0 < x < 1, t > 0, given, u(x, 0) = 100(x – x2), ut(x, 0) = 0, u(0, t) = u(1, t) = 0, t > 0,, by finite difference method for one time step with h = 0.25., , (A.U. Apr/May 2000), , 5. Solve utt = uxx, 0 < x < 1, t > 0, u(0, t) = u(1, t) = 0, t > 0, u(x, 0) = x – x2, ut(x, 0) = 0, taking, h = 0.2 up to one half of the period of vibration by taking appropriate time step., (A.U. Nov/Dec. 1999), 6. Solve utt = uxx, 0 < x < 1, t > 0, given, u(x, 0) = ut(x, 0) = u(0, t) = 0, and u(1, t) = 100 sin (π t)., Compute u for four time steps with h = 0.25., , (A.U. Nov/Dec. 2003), , 7. Approximate the solution to the equation uxx – utt = 0, 0 < x < 1, t > 0,, u(0, t) = u(1, t) = 0, t > 0, u(x, 0) = 1, 0 ≤ x ≤ (1/2), and u(x, 0) = – 1, (1/2) < x ≤ 1, and, ut(x, 0) = 0,, using h = k = 0.1 for three time steps., , (A.U. Nov/Dec. 2005), , 8. Solve utt = uxx, subject to the following conditions, u(0, t) = u(1, t) = 0, t > 0, and ut(x, 0) = 0, u(x, 0) = sin3 (π x), 0 ≤ x ≤ 1,, taking h = 1/4. Compute u for four time steps., , (A.U. Apr/May 2006), , 9. Approximate the solution of the wave equation utt = uxx, 0 < x < 1, t > 0,, u(0, t) = u(1, t) = 0 and u(x, 0) = sin (2π x), and ut(x, 0) = 0, 0 ≤ x ≤ 1,
Page 318 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 307, , using the implicit method given in Eq.(5.72), with ∆x = 0.25, and ∆t = 0.25 for two time, steps., 10. Using the implicit method given in Eq.(5.74), solve utt = uxx, 0 < x < 1, t > 0, given, u(x, 0) = 100(x – x2), ut(x, 0) = 0, u(0, t) = u(1, t) = 0, t > 0, with k = 0.25, h = 0.25., Compute for two time steps., , 5.7, , ANSWERS AND HINTS, , Exercise 5.1, In all problems, the resulting equations are solved by the Gauss elimination procedure., 1. y1 = 0.23159, y2 = 0.46681, y3 = 0.71661., 2. y1 = 0.39707, y2 = 0.94938, | ε1 | = 0.00146, | ε2 | = 0.00165., 3. y1 = 0.13319, y2 = 0.28408, y3 = 0.45503., 4. y1 = 1.45488, y2 = 2.22502, | ε1 | = 0.00301, | ε2 | = 0.00378., 5. y1 = 0.44811, y2 = 0.84397, y3 = 1.08650., 6. y1 = – 0.04400, y2 = – 0.04217., 7. y1 = 0.21767, y2 = – 0.00218., 8. y1 = 2.16811, y2 = 2.10435, y3 = 1.54319., 9. y1 = 0.04400, y2 = 0.04217., 10. (i) y1 = – 0.00152, y2 = 0.01220, y3 = – 0.11128. (Oscillatory solutions). Errors in magnitude: 0.00203, 0.00551, 0.19332., (ii) y1 = 0.01677, y2 = 0.07547, y3 = 0.28092. Errors in magnitude: 0.01626, 0.06878,, 0.19888., (iii) y1 = 2.07692, y2 = 0.69231, y3 = 1.61538. Errors in magnitude: 2.07641, 0.68562,, 1.53334., Exercise 5.2, 1. Elliptic for all (x, y)., 3. Elliptic for, , x2, , +, , y2, , < 0.25, parabolic for, , 2. Hyperbolic for all (x, y)., x2, , + y2 = 0.25, hyperbolic for x2 + y2 > 0.25., , 4. Hyperbolic for all (x, y)., 5. Elliptic for x2 + 4y2 > 4, parabolic for x2 + 4y2 = 4, hyperbolic for x2 + 4y2 < 4., Exercise 5.3, In all the problems, we obtain the mesh as given in Fig.5.35., Using the standard five point formula, we obtain the system of equations as Au = b, where
Page 319 :
308, , NUMERICAL METHODS, , LM− 4, 1, A=M 1, MN 0, and, , OP, PP, Q, , 1, 1, 0, 0, 1, −4, ,u=, 0 −4, 1, 1, 1 −4, , LMu OP, MMuu PP, Nu Q, 1, , 2, , u1, , u2, , u3, , u4, , 3, 4, , bi , i = 1, 2, 3, 4 are obtained from boundary conditions. In, , Problems 1 to 9, we have solved the systems by Gauss elimination method., , Fig. 5.35. Example 5.3., , 1. b = [4/3, 0, 0, – 4/3]T, u1 = – 1/3, u2 = 0, u3 = 0, u4 = 1/3., 2. b = [1, – 7, – 3, – 11]T, u1 = 1, u2 = 3, u3 = 2, u4 = 4., 3. b = [– 600, – 1000, – 200, – 600]T, u1 = 300, u2 = 400, u3 = 200, u4 = 300. (By symmetry, we can start by setting u1 = u4)., 4. b = [– 3, – 12, 0, – 3]T, u1 = 2, u2 = 4, u3 = 1, u4 = 2. (By symmetry we can start by setting, u1 = u4)., 5. b = [– 2, – 9, – 1, – 6]T, u1 = 5/3, u2 = 10/3, u3 = 4/3, u4 = 8/3., 6. b = [4/3, 0, 0, – 4/3]T, u1 = – 1/3, u2 = 0, u3 = 0, u4 = 1/3. (By symmetry we can start by, setting u2 = u3)., 7. b = [– 10/9, – 22/9, 2/9, – 10/9]T, u1 = 5/9, u2 = 8/9, u3 = 2/9, u4 = 5/9., 8. b = [43/27, 10/27, 5/27, – 28/27]T, u1 = – 101/216, u2 = – 35/216, u3 = – 25/216, u4 = 41/, 216., 9. b = [5, 8, 2, 5]T, u1 = – 5/2, u2 = – 13/4, u3 = – 7/4, u4 = – 5/2. (By symmetry we can start, by setting u1 = u4)., 10. We obtain the initial approximation u1(0) using the five point diagonal formula and u 4 = 0,, whereas u2( 0) , u3(0) , u4(0) are obtained by the standard five point formula, unless stated, other wise., (i) 0, 1.75, 1.1875, 3.48438; 0.48438, 2.74219, 1.74219, 3.87110; 0.87110, 2.93555,, 1.93555, 3.96778; 0.96778, 2.98389, 1.98389, 3.99195; 0.99195, 2.99598, 1.99598,, 3.99799., (ii) 225.0, 306.25, 106.25, 253.125; 253.125, 376.5625, 176.5625, 288.28125; 288.28125,, 394.14063, 194.14063, 297.70315; 297.70315, 398.69337, 198.85158, 299.38624;, 299.38624, 399.69312, 199.69312, 299.84656., (iii) 1.5, 3.375, 0.375, 1.6875; 1.6875, 3.84375, 0.84375, 0.42188; 1.92188, 3.58594, 0.58594,, 0.29297; 1.79297, 3.52149, 0.52149, 0.26074; 1.76075, 3.50537, 0.50537, 0.25269., (iv) – 0.41667, – 0.10417, – 0.10417, 0.28125; – 0.45023, – 0.13484, – 0.08854, 0.20341;, – 0.45399, – 0.15524, – 0.10894, 0.19321; – 0.46419, – 0.16034, – 0.11404, 0.19066;, – 0.46674, – 0.16161, – 0.11532, 0.19003., (v) Set all initial approximations as zeros. – 1.25, – 2.3125, – 0.8125, – 2.03125; – 2.03125,, – 3.01563, – 1.51563, – 2.38282; – 2.38282, – 3.19141, – 1.69141, – 2.47071; – 2.47071,, – 3.23535, – 1.73537, – 2.49268. (If we use symmetry, that is, u1 = u4, we get the, fourth iteration as – 2.48047, – 3.24024, – 1.74024).
Page 320 :
BOUNDARY VALUE PROBLEMS IN ORDINARY DIFFERENTIAL EQUATIONS..., , 309, , Exercise 5.4, 1. 0.09668, 0.13672, 0.09668., , 2. 0.12095, 0.17053, 0.12095., , 3. 0.125, 0.25, 0.125., 4. (i) 0, 0, 0; (ii) 0.0625, 0, – 0.0625; (iii) 0.08779, 0, – 0.08779., 5. The given data is discontinuous. The effect of the singularities at (0, 0), (5, 0) is propagated, into the interior when we use finite difference methods. Such problems require special, techniques to deal with singularities. In the present problem, if we take the initial, conditions valid at (0, 0) and (5, 0), that is, u0, 0 = 20, u5,0 = 20, we obtain the solutions as, 15.0239, 20.0957, 25.3588, 41.3397., 6. 0.7328, | ε | = 0.0114., , 7. 2.2345, 3.8069., , 8. 1/9, 0, – 1/9; 1/81, 0, – 1/81; | ε1 | = | ε3 | = 0.00695, | ε2 | = 0., 9. 0.749665, 0.499943, 0.24999; 0.748856, 0.499723, 0.249941., 10. 0.740683, 1.332299, 0.740683; 0.716668, 1.198160, 0.716668., Exercise 5.5, 1. 0.5, 0.70711, 0.5; 0, 0, 0; – 0.5, – 0.70711, – 0.5., 2. Use explicit method. Assume h = 0.25. 10.1775, 10.24, 10.1775; 8.5491, 10.21, 8.5491;, 5.8186, 9.6485, 5.8186; 2.7699, 7.8614, 2.7699; 0.0927, 4.4450, 0.0927., 3. Use explicit method. 0, 0, 0; – 1, 0, 1; 0, 0, 0., 4. Use explicit method. Since k is not prescribed, choose k = h such that r = 1. 12.5, 18.75,, 12.5., 5. Use explicit method. Period of vibration = [(2l /c)] = 2. Computations are to be done up, to t = 1. Since k is not prescribed, choose k = 0.2 such that r = (k/h) = 1., 0.12, 0.20, 0.20, 0.12; 0.04, 0.08, 0.08, 0.04; – 0.04, – 0.08, – 0.08, – 0.04; – 0.12, – 0.20,, – 0.20, – 0.12; – 0.16, – 0.24, – 0.24, – 0.16., 6. Use explicit method. Since k is not prescribed, choose k such that r = (k/h) = 1., 0, 0, 0; 0, 0, 50 2 ; 0, 50 2 , 100; 50 2 , 100, 50 2 ., 7. The given data is discontinuous. The effect of the singularity at x = 1/2 is propagated, into the interior when we use finite difference methods. Such problems require special, techniques to deal with singularities. Use explicit method. Since k is not prescribed,, choose k such that r = (k/h) = 1; 1, 1, 1, 1, 0, 0, – 1, – 1, – 1; 0, 1, 1, 0, 0, 0, 0, – 1, 0; 0, 0,, 0, 0, 0, 0, 0, 1, 0., 8. Use explicit method. Since k is not prescribed, choose k such that r = (k/h) = 1., 0.5, 1 /( 2 2 ) , 0.5; 0, 0, 0; – 0.5, – 1 /(2 2 ) , – 0.5; – 1 /(2 2 ) , – 1, – 1 /( 2 2 ) ., 9. 0.5, 0, – 0.5; – 0.5, 0, 0.5., 10. 15.17857, 20.53571, 15.17857; 5.86734, 8.67346, 5.86734.
Page 321 :
This page, intentionally left, blank
Page 322 :
Bibliography, The following is a brief list of texts on numerical methods. There are various other texts which, are not reported here., 1. Atkinson, K., Elementary Numerical Analysis, Wiley, New York, 1985., 2. Burden, R.L., and J.D. Faires, Numerical Analysis, 4th edition, PWS-Kent, 1989., 3. Butcher, J.C., The Numerical Analysis of Ordinary Differential Equations: Runge-Kutta, and General Linear Methods, Wiley, New York, 1987., 4. Collatz. L., Numerical Treatment of Differential Equations, 3rd edition, Springer Verlag,, Berlin, 1966., 5. Conte, S.D., and C. deBoor, Elementary Numerical Analysis: An Algorithmic Approach,, 3rd edition, McGraw-Hill, New York, 1980., 6. Dahlquist, G., and A. Bjorck, Numerical Methods, Prentice Hall, Englewood Cliffs, N.J,, 1974., 7. David Kincaid and W. Cheney, Numerical Analysis, Brooks/ Cole, Calif., 1991., 8. Ferziger, J.H., Numerical Methods for Engineering Application, John Wiley, New York,, 1981., 9. Fox, L., Numerical Solution of Ordinary and Partial Differential Equations, Pergamon,, London, 1962., 10. Froberg, C.E., Introduction to Numerical Analysis, Addison-Wesley, Reading, Mass.,, 1969., 11. Gear, C.W., Numerical Initial Value Problems in Ordinary Differential Equations,, Prentice-Hall, Englewood Cliffs, N.J., 1971., 12. Gerald, C.F., and P.O. Wheatley, Applied Numerical Analysis, 4th Ed., Addison-Wesley,, Reading, Mass., 1989., 13. Henrici, P., Elements of Numerical Analysis, John Wiley, New York, 1964., 14. Householder, A.S., Principles of Numerical Analysis, McGraw-Hill, New York, 1953., 15. Issacson, E., and H.B. Keller, Analysis of Numerical Methods, John Wiley, New York,, 1966., 16. Jain, M.K., Numerical Solution of Differential Equations, 2nd ed., Wiley Eastern Ltd.,, New Delhi, 1984., 17. Jain, M.K., S.R.K. Iyengar., and R.K. Jain, Numerical Methods for Scientific and, Engineering Computation, Sixth Edition, New Age International Publishers, (Formerly, Wiley Eastern Limited), New Delhi, 2008., , 311
Page 323 :
312, , NUMERICAL METHODS, , 18. Johnson, L.W., and R.D. Riess., Numerical Analysis, 2nd ed., Addison-Wesley, Reading, Mass., 1982., 19. Lambert, J.D., Computational Methods in Ordinary Differential Equations, John Wiley,, New York, 1973., 20. Lapidus, L., and J. Seinfeld, Numerical Solution of Ordinary Differential Equations,, Academic Press, New York, 1971., 21. Ralston, A., and P. Rabinowitz, A first course in Numerical Analysis, 2nd ed., McGrawHill, New York, 1978., 22. Scheid, F., Numerical Analysis, McGraw-Hill, New York, 1988., 23. Todd, J., Survey of Numerical Analysis, McGraw-Hill, New York, 1962.
Page 324 :
Index, Crank-Nicolson method, 283, , A, , cubic splines, 99, , abscissas, 128, Adams-Bashforth methods, 217, Adams-Bashforth predictor corrector methods, 227, , D, , Adams-Moulton methods, 221, , Descarte’s rule of signs, 4, , algebraic equation, 1, , diagonal system of equations, 26, , amplification factor, 238, , diagonally dominant, 42, 47, , agumented matrix, 25, , diagonal five point formula, 256, 257, direct methods, 2, 26, Dirichlet boundary value problem, 252, , B, back substitution method, 27, backward Euler method, 193, Bender-Schmidt method, 277, , discretization, 253, divided differences, 70, double integration, 169, , boundary conditions, Dirichlet, 252, , E, , first kind, 242, , eigen value problem, 52, , mixed kind, 242, , eigen vector, 53, , second kind, 242, , elementary column transformation, 27, , third kind, 242, , elementary row transformation, 27, error of approximation, 63, , C, characteristic equation, 52, chord method, 6, 11, complete pivoting, 29, condition of convergence, 16, , error tolerance, 3, 41, Euler method, 185, Euler-Cauchy method, 194, explicit methods, 183, 276, 291, extrapolation, 186, , consistent system of equations, 26, convergence of iteration methods, 19, , F, , corrector methods, 221, , finite differences, 80, , Cotes numbers, 129, , backward difference operator, 81, , 313
Page 325 :
314, , NUMERICAL METHODS, , central difference operator, 83, derivative operator, 87, forward difference operator, 80, mean operator, 85, shift operator, 80, finite difference method, 242, 252, , L, Lagrange fundamental polynomials, 65, Lagrange interpolating polynomial, 65, Laplace equation, 252, Liebmann iteration, 263, , fixed point iteration method, 15, , linear interpolation method, 6, , G, , M, , Gauss elimination method, 28, , mesh points, 182, , Gauss-Jacobi iteration method, 41, Gauss-Jordan method, 35, Gauss-Seidel iteration method, 46, general iteration method, 15, grid points, 182, , mesh ratio parameter, 276, 292, method of false position, 6, method of simultaneous displacement, 42, method of successive approximation, 15, mid-point method, 193, Milne’s predictor-corrector method, 227, Milne-Simpson method, 225, , H, , modified Euler method, 193, , heat equation, 275, , multi step methods, 183, 216, , Heun’s method, 194, , multiple root, 2, , I, , N, , implicit methods, 183, 275, 282, 301, , natural spline, 100, , inconsistent system of equations, 26, , Newton-Cotes integration rules, 129, , initial approximation, 3, , Newton-Raphson method, 11, , initial boundary value problem, 251, 275, , Newton’s interpolating polynomial using, , initial conditions, 180, 275, , backward differences, 92, , initial point, 180, , divided differences, 72, , initial value problem, 180, , forward differences, 90, , intermediate value theorem, 4, , nodes, 63, 242, 253, , interpolating conditions, 63, , numerical differentiation using, , interpolating polynomial, 63, , backward differences, 117, , inverse interpolation, 76, , divided differences, 122, , iteration function, 3, 15, iterative methods, 3, 26, 41, 263, , forward differences, 109, numerical integration, 128, composite Simpson’s 1/3 rule, 139, composite Simpson’s 3/8 rule, 144, , J, Jacobi method, 41, , composite trapezium rule, 131
Page 326 :
315, , INDEX, , Gauss-Legendre methods, 160, Romberg integration, 147, Simpson’s 1/3 rule, 136, Simpson’s 3/8 rule, 144, trapezium rule, 129, , S, Schmidt method, 276, simple root, 2, single step methods, 183, spline, 99, spline function, 99, , O, , stability, 237, , operation count, 2, 26, , standard five point formula, 253, 257, , order, 19, 128, 183, , step length, 242, , P, , T, , partial differential equations,, , tabular points, 63, , elliptic, 251, , tangent method, 11, , hyperbolic, 251, , Taylor series method, 184, 208, , parabolic, 251, , transcendental equation, 1, , partial pivoting, 29, , trapezium method 194, 223, , permanence property, 70, , truncation error, 183, 255, , Poisson equation, 252, , two point boundary value problem, 241, , power method, 53, predictor-corrector methods, 216, 225, , U, unconditionally stable methods, 237, , Q, , upper triangular system of equations, 27, , quadrature formula, 128, , W, R, , wave equation, 291, , rate of convergence, 19, , weight function, 128, , regula-falsi method, 6, root, 1, Runge-Kutta methods, 200, second order, 200, fourth order, 202
