Page 1 : IWAICIS-LIM/E ©) ms 7, , PAPER-I, SEMESTER-1, (MORNING SESSION), , (10 PASS TWO YEAR TRADES), , , , PART-B (ENGINEERING DRAWING) (Marks : 75), , Choose the correct answers: . ——————, , With the help of ruler and compass it is NOT possible to construct angel of ~, a) 37,5" b) 40" c) 22.5" d) 67.5°, , Which one of the following compass is used to draw very large circles?, &) Beam b) Large c) Bow d) Drop, , Lettering of drawing sheet should have —, , a) In a sentence only first alphabet in capital letters, b) All alphabets in small letters, , ©) In a sentence only abbreviations in capital letters, , d) All alphabets in capital letters, , During operation of drafter, the two arms of the drafter remains at ~, , a) 45° b) 90" c) 180° 4) 270°, Which one of the following compass is used to draw SMALL size circles?, a) Beam b) Large c) Bow d) Drop, Which one of the following pencil leads is the hardest’?, , a) HB b)H )B dF, To lay off an angle from a given line, what marks on the protractor should your align for, higher accuracy —, , a) Centre mark and 0 marks only b) 0° and 180° marks only, , c) 0°, 180° and Centre marks d) 0°, 90° and 180° marks, Parallel lines can be drawn with the help of —, , 8) Mini drafter b) T square, , c) Pair of set squares d) All of these, , To draw a perpendicular from a given point P on line XY, name the point where the, needle of the compass should be placed first —, , a) At point P b) Any convenient point along Xy, ¢) At point X or Y d) A point near the mid point of PX and PY, cast with, nitro™ profession:, , ent ee tet ae eee

Page 2 : 18/A/C/S-1/4/E 2 ign,, , 10,, , aR, , 5., , 14,, , 15., , 17., , 19,, , 20., , - A title block contains all of the following, a) Name and address of the company b) Parts list, , A drawing instrument set usually contains all of the following except —, 2) Bow compass b) Scale ¢) Dividers d) Extra leads, , In engineering system of paper sizes, which of the following is A2 size ~, a) 841 mm x 1189 mm b) 594 mm x 841 mm, c) 420 mm x 594 mm d) 210 mm x 297 mm, , c) Drawing sheet size letter designation d) Drawing number, , Which of the following pairs of orthographic views both show the height dimension?, a) Left side and front b) Top and Front, , ¢) Top and Rear : d) Bottom and Right side, , Centre line are drawn as —, , 4) Continuous narrow lines b) Dashed narrow lines, , c) Long dashed dotted narrow lines d) Long dashed double dotted narrow lines, Projection of an object shown by three views is known as —, , 8) Perspective b) Isometric ¢) Oblique d) Orthographic, ‘The type of pictorial projection generally used by the architect is —, , 8) Orthography b) Oblique ¢) Perspective d) Isometric, , fe fecommended symbol for indicating the angle of projection shows two views of the, frustum of a—, , a) Square pyramid b) Triangular pyramid, , ¢) Cone d) Any of these, , ‘The projection in isometric view are, , 4) Converging b) Parallel to the plane of projection, , c) Diverging d) Perpendicular to the plane of projection, , Which of the following purpose is NOT served by a divider?, , a) Divide lines or curves into a number of equal parts, , b) Transfer measurements from one part of the drawing to another part, ©) Make full size, reduced size of enlarged size drawing, , 4) Set off a series of equal distances on the drawing, , The inclination of letters as recommended by BIS is —, a) 75° b) 70° c) 65° d) 60°, , created with, , ee ee eee rome ce ee

Page 3 : 18/A/C/S-1/4/E a, , 21,, , 23,, , 24., , 25., , Ce) oe, , , , Two point perspective are drawn by —, , a) Single vanishing point method b) Double vanishing point method, , ¢) Triple vanishing point method d) All of these, , If a line intersects a circle at two points and does not pass through the centre this line, segment is called as —, , a) Diameter _ b) Chord c) Radial line 4) Quadrant, , Methods of arrangement of dimensions includes —, , 2) Parallel, continuous and combined, , b) Perpendicular, parallel and combined, ©) Perpendicular, continuous and combined, d) Perpendicular, parallel and continuous, , Select the correct isometric view corresponding to the orthographic views shown ~, , 7 DOGS, , The thickness of the line of a letter with 14mm height in B type lettering is —, a) 1 mm b) 1.5mm ¢) 1.25 mm d) 2mm, , , , , , , , , , Heeererreee, , created with, , atelier a te meee